EN ISO 11296-2:2018
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
ISO 11296-2:2018, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground non-pressure drainage and sewerage networks. It is applicable to polyethylene (PE) pipes of three different types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 11296-2:2018 covers:
- jointing of pipe lengths by means of butt fusion;
- fabricated and injection-moulded fittings made of PE.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO 11296-2:2018)
Diese Internationale Norm legt in Verbindung mit Teil 1 die Anforderungen und Prüfverfahren für Rohre und Formstücke fest, die Teil eines Kunststoff-Rohrleitungssystems sind und die als Rohrstrang-Lining bei der Renovierung erdverlegter druckloser Entwässerungsnetze eingebaut werden. Drei verschiedenen Arten von PE-Rohren können dafür angewendet werden:
einschichtige PE-Vollwandrohre (Nenn-Außendurchmesser, dn), mit Kennzeichnungsstreifen;
PE-Rohre mit koextrudierten Schichten auf der Innen- oder Außenseite des Rohres oder beides (Gesamt-Außendurchmesser, dn), wie in Anhang A festgelegt, worin alle Schichten den gleichen MRS-Wert haben;
beschichtete PE-Rohre (Außendurchmesser, dn) mit einer abziehbaren, zusammenhängenden, thermoplastischen Zusatzschicht auf der Rohr-Außenseite („beschichtetes Rohr“), siehe Anhang A.
Zusätzlich wird betrachtet:
Verbindung von Rohrlängen durch Stumpfschweißen;
vorgefertigte und Spritzguss-Formstücke aus PE.
Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO 11296-2:2018)
ISO 11296-2:2018, lu conjointement avec l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai pour des tuyaux et raccords intégrés aux systèmes de canalisations en plastique installés sous forme de tuyaux continus et utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression. Il s'applique aux tuyaux en PE de trois types différents:
- tuyaux en PE monocouches à paroi compacte (diamètre extérieur nominal, dn), y compris les bandes d'identification éventuelles;
- tuyaux en PE avec des couches co-extrudées à l'extérieur et/ou à l'intérieur du tuyau (diamètre extérieur total, dn), tels que spécifiés dans l'Annexe A, toutes les couches ayant la même classification MRS;
- tuyaux revêtus de PE (diamètre extérieur, dn) comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau («tuyau revêtu»), voir l'Annexe A.
ISO 11296-2:2018 couvre également:
- l'assemblage des longueurs de tuyau par soudage bout à bout;
- les raccords en PE façonnés et moulés par injection.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11296-2:2018)
Ta 2. del standarda EN 13566, bran v povezavi s 1. delom, določa zahteve in preskusne metode za cevi in fitinge, ki so del plastičnih cevnih sistemov, nameščenih kot neprekinjene cevi pri obnovi omrežij za odvodnjavanje in kanalizacijo, ki obratujejo brez tlaka. Zajema:
– homogene stenske cevi (HW), izdelane iz polietilena (PE) ali polipropilena (PP);
– konstrukcijske stenske cevi (SW) valovitega dvojno-stenskega tipa konstrukcije, kot je določen v dodatku B, katerih konstrukcijske plasti so izdelane iz PE ali PP;
– spajanje dolžin cevi s soležnim taljenjem (HW) ali elektrofuzijo (SW);
– oblikovane in brizgano lite fitinge iz PE, PP in poli(vinilklorida) (PVC-U).
OPOMBA: Postopek nanašanja malte ne spada na področje uporabe tega standarda.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2018
1DGRPHãþD
SIST EN 13566-2:2006
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 2.
del: Oblaganje z neprekinjenimi cevmi (ISO 11296-2:2018)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
Kunststoff-Rohrleitungssysteme zur Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO 11296-
2:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 2:
Tubage par tuyau continu avec espace annulaire (ISO 11296-2:2018)
Ta slovenski standard je istoveten z: EN ISO 11296-2:2018
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11296-2
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 23.040.45; 23.040.20; 91.140.80; 93.030 Supersedes EN 13566-2:2005
English Version
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 2:
Lining with continuous pipes (ISO 11296-2:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme zur Renovierung von
rénovation des réseaux de branchements et de erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO
Partie 2: Tubage par tuyau continu avec espace 11296-2:2018)
annulaire (ISO 11296-2:2018)
This European Standard was approved by CEN on 10 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11296-2:2018) has been prepared by Technical Committee ISO/TC 138
“Rehabilitation of pipeline systems” in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13566-2:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11296-2:2018 has been approved by CEN as EN ISO 11296-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-2
First edition
2018-02
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 2:
Lining with continuous pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 2: Tubage par tuyau continu avec espace annulaire
Reference number
ISO 11296-2:2018(E)
©
ISO 2018
ISO 11296-2:2018(E)
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2018 – All rights reserved
ISO 11296-2:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 2
4.1 Symbols . 2
4.2 Abbreviated terms . 2
5 Pipes at the “M” stage . 2
5.1 Material . 2
5.2 General characteristics . 2
5.3 Material characteristics . 3
5.4 Geometrical characteristics . 3
5.5 Mechanical characteristics. 3
5.6 Physical characteristics . 3
5.7 Jointing . 3
5.8 Marking . 3
5.9 Regional requirements for pipes . 3
6 Fittings at the “M” stage . 3
6.1 Requirements . 3
6.2 Marking . 3
6.3 Regional requirements for fittings . 3
7 Ancillary components . 3
8 Fitness for purpose of the system for pipes and fittings at the “I” stage .4
9 Installation practice . 4
9.1 Preparatory work . 4
9.2 Storage, handling and transport . 4
9.3 Equipment . 4
9.3.1 Butt fusion equipment and de-beading equipment. 4
9.3.2 Pipe rollers . 5
9.3.3 Winching and rod-pulling equipment . 5
9.3.4 Pipe entry guides . 5
9.3.5 Electrofusion equipment . 5
9.3.6 Inspection equipment . 5
9.3.7 Lifting equipment . 5
9.4 Installation . 5
9.5 Process-related inspection and testing . 6
9.6 Lining termination . 6
9.7 Reconnection to the existing pipeline system . 6
9.8 Final inspection and testing . 6
9.9 Documentation .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.