EN 16867:2020

SLOVENSKI STANDARD
01-maj-2020
Stavbno okovje - Mehatronsko okovje za vrata - Zahteve in preskusne metode
Building hardware - Mechatronic door furniture - Requirements and test methods
Schlösser und Baubeschläge - Mechatronische Türbeschläge - Anforderungen und
Prüfverfahren
Quincaillerie pour le bâtiment - Ensemble plaques béquilles mécatroniques - Exigences
et méthodes d'essai
Ta slovenski standard je istoveten z: EN 16867:2020
ICS:
91.190 Stavbna oprema Building accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16867
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 91.190
English Version
Building hardware - Mechatronic door furniture -
Requirements and test methods
Quincaillerie pour le bâtiment - Poignée de porte Schlösser und Baubeschläge - Mechatronische
mécatronique - Exigences et méthodes d'essai Türbeschläge - Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 27 January 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16867:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 10
5 Test — general and test apparatus . 27
6 Test methods — procedures . 27
7 Classification system . 54
8 Marking . 56
Annex A (normative) MDF suitable for use on fire resistant / smoke control doors . 57
Annex B (normative) Tool sets for attack resistance tests . 58
Annex C (informative) Table of test procedures . 60
Annex D (informative) Manufacturer’s declaration of compliance . 62
Annex E (informative) Examples of calculation of effective code variations for ICC . 64
Bibliography . 66

European foreword
This document (EN 16867:2020) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards shall
be withdrawn at the latest by September 2020.
This document is one of a series of European standards dedicated to building hardware products.
European standards for mechanically operated lever handles and knob furniture (EN 1906) are also
available.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these products throughout CEN
Member.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
The development of building hardware to include electrically and electronic operations and control has
introduced a large number of products on the market.
For locks and door furniture, the range of electrical or electronic components to be fitted to existing
mechanical locks or door furniture to a complete Mechatronic Door Furniture (MDF) has increased.
Also, complete units with lock and door furniture in unique combination to MDF occur frequently.
Typically, MDF is installed directly on the door leaf and includes all functions like operating the follower
of the lock, reading and decoding the credential and power.
Following components and units are covered by this document.
Type A: Handle or knob operated door furniture with electrically operated actuator, reading unit for
credential and power supply to be combined with a mechanical operated lock where the lock meets
EN 12209 or EN 15685.
Type B: Handle or knob operated door furniture with reading unit for credential and power supply to be
combined with electrically operated locks where the lock meets EN 14846.
This document does not cover electrically operated locks or striking plates in combination with an access
control system not fitted on the door.
This document provides the MDF with requirements for:
— category of use to ensure the performance during its normal use;
— durability to ensure good performance during lifetime;
— specification for system management;
— suitability for use on fire resistant/smoke controlled doors;
— environmental resistance for good performance during lifetime in different environmental
conditions;
— security for different types of credentials;
— attack resistance to ensure use on Burglary resistant doors;
— product information to give summary of the performance.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these devices throughout CEN
Member States.
It is assumed that MDF will conform to the legal regulations i.e. RED – Radio Equipment Directive
2014/53/EU.
On occasion, there could be a need for additional functions within the design of the MDF. Purchasers
should convince themselves that the products are suitable for their intended use. This is particularly
important when the operation of such additional functions is safety-related. Accordingly, this document
includes assessment of such features when they are included in the MDF design.
1 Scope
1.1 General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the
possibility to control the locking and/or release part through an electronic authorization means. This can
be operable by credentials (i.e. card, code, biometric).
The MDF, according to this document, is combined with locks according to EN 12209, EN 14846,
EN 15685 or can be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF can be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use,
durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests
conducted in addition to the performance testing specified by this document.
1.2 Exclusions
This document does not cover:
— mechatronic cylinders according to EN 15684;
— electromechanical operated locks and striking plates according to EN 14846.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 636:2012+A1:2015, Plywood — Specifications
EN 1303, Building hardware — Cylinders for locks - Requirements and test methods
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-2, Fire resistance and smoke control tests for door, shutter and openable window assemblies and
elements of building hardware — Part 2: Fire resistance characterisation test for elements of building
hardware
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware — Part 3: Smoke control test for door and shutter assemblies
EN 1670:2007, Building hardware — Corrosion resistance — Requirements and test methods
EN 1906:2012, Building hardware — Lever handles and knob furniture — Requirements and test methods
EN 14846, Building hardware — Locks and latches — Electromechanically operated locks and striking
plates - Requirements and test methods
EN 15684, Building hardware — Mechatronic cylinders — Requirements and test methods
EN 15685, Building hardware — Requirements and test methods — Multipoint locks, latches and locking
plates — Characteristics and test methods
EN 60068-2-1, Environmental testing — Part 2-1: Tests — Test A: Cold
EN 60068-2-2, Environmental testing — Part 2-2: Tests — Test B: Dry heat
EN 60068-2-6, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal)
EN 60068-2-27, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock
EN 60068-2-30, Environmental testing — Part 2-30: Tests — Test Db and guidance: Damp heat, cyclic (12
+ 12 hour cycle)
EN 60529, Degrees of protection provided by enclosures (IP Code)
EN 61000-4-2, Electromagnetic compatibility (EMC) — Part 4-2: Testing and measurement techniques -
Electrostatic discharge immunity test
EN 61000-4-3, Electromagnetic compatibility (EMC) — Part 4-3: Testing and measurement techniques —
Radiated, radio-frequency, electromagnetic field immunity test
EN 61000-4-4, Electromagnetic compatibility (EMC) — Part 4-4: Testing and measurement techniques —
Electrical fast transient/burst immunity test
EN 61000-4-5, Electromagnetic compatibility (EMC) — Part 4-5: Testing and measurement techniques —
Surge immunity test
EN 61000-4-11, Electromagnetic compatibility (EMC) — Part 4-11: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations immunity tests
EN 61000-4-29, Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques -
Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
EN ISO 10666, Drilling screws with tapping screw thread — Mechanical and functional properties
(ISO 10666)
EN ISO 15480, Fasteners — Hexagon washer head drilling screws with tapping screw thread (ISO 15480)
EN ISO 15481, Cross recessed pan head drilling screws with tapping screw thread (ISO 15481)
EN ISO 15482, Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482)
EN ISO 15483, Cross recessed raised countersunk head drilling screws with tapping screw thread
(ISO 15483)
ISO/IEC 18033-3, Information technology — Security techniques — Encryption algorithms — Part 3: Block
ciphers
ISO 10899, High-speed steel two-flute twist drills - Technical specifications
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
access card
card or tag, read only or read write, without integrated circuit, does not provide encryption
Note 1 to entry: Can be used with contact or contactless
EXAMPLE magnetic stripe, barcode
3.2
actuator
electrically operated means to affect or
...