EN ISO 15883-2:2009

SLOVENSKI STANDARD
01-september-2009
1DGRPHãþD
SIST EN ISO 15883-2:2006
ýLVWLOQRGH]LQIHNFLMVNHQDSUDYHGHO=DKWHYHLQSUHVNXVL]DþLVWLOQR
GH]LQIHNFLMVNHQDSUDYHVWRSORWQRGH]LQIHNFLMR]DNLUXUãNHLQVWUXPHQWH
DQHVWH]LMVNRRSUHPRSRVRGHLGU,62
Washer-disinfectors - Part 2: Requirements and tests for washer-disinfectors employing
thermal disinfection for surgical instruments, anaesthetic equipment, bowls, dishes,
receivers, utensils, glassware, etc. (ISO 15883-2:2006)
Reinigungs-Desinfektionsgeräte - Teil 2: Anforderungen und Prüfverfahren von
Reinigungs-Desinfektionsgeräten mit thermischer Desinfektion für chirurgische
Instrumente, Anästhesiegeräte, Gefäße, Utensilien, Glasgeräte usw. (ISO 15883-2:2006)
Laveurs désinfecteurs - Partie 2: Exigences et essais pour laveurs désinfecteurs
destinés à la désinfection thermique des instruments chirurgicaux, du matériel
d'anesthésie, des bacs, plats, récipients, ustensiles, de la verrerie, etc. (ISO 15883-
2:2006)
Ta slovenski standard je istoveten z: EN ISO 15883-2:2009
ICS:
11.080.10 Sterilizacijska oprema Sterilizing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15883-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2009
ICS 11.080.10 Supersedes EN ISO 15883-2:2006
English Version
Washer-disinfectors - Part 2: Requirements and tests for
washer-disinfectors employing thermal disinfection for surgical
instruments, anaesthetic equipment, bowls, dishes, receivers,
utensils, glassware, etc. (ISO 15883-2:2006)
Laveurs désinfecteurs - Partie 2: Exigences et essais pour Reinigungs-Desinfektionsgeräte - Teil 2: Anforderungen
laveurs désinfecteurs destinés à la désinfection thermique und Prüfverfahren von Reinigungs-Desinfektionsgeräten
des instruments chirurgicaux, du matériel d'anesthésie, des mit thermischer Desinfektion für chirurgische Instrumente,
bacs, plats, récipients, ustensiles, de la verrerie, etc. (ISO Anästhesiegeräte, Gefäße, Utensilien, Glasgeräte usw.
15883-2:2006) (ISO 15883-2:2006)
This European Standard was approved by CEN on 16 May 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15883-2:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 93/42/EEC .4

Foreword
The text of ISO 15883-2:2006 has been prepared by Technical Committee ISO/TC 198 “Sterilization of health
care products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
15883-2:2009 by Technical Committee CEN/TC 102 “Sterilizers for medical purposes” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2009, and conflicting national standards shall be withdrawn
at the latest by March 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15883-2:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive.
For relationship with EC Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15883-2:2006 has been approved by CEN as a EN ISO 15883-2:2009 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 93/42/EEC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 93/42/EEC on medical devices.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the clauses of this
standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 93/42/EEC on medical
devices
Clauses/subclauses of this Essential requirements (ERs) of EU Qualifying remarks/Notes
International Standard Directive 93/42/EEC
4.1.1 1, 2, 3, 4, 5, 6, 7.1, 7.2, 7.3, 7.5, 7.6, 8.1, 9.1, The WD shall comply with the
9.2, 9.3, 12.1, 12.5, 12.6, 12.7.1, 12.7.2, 12.7.3, requirements of ISO 15883-1:—
12.7.5, 13.1, 13.3, 13.4
4.1.2 1, 3, 4, 6, 7.1, 8.1, 9.1
4.1.3 1, 3, 4, 6, 7.1, 8.1, 9.1
4.1.5 3, 7.1
4.1.6 7.3, 8.1
4.2 3, 8.1
4.3 3, 8.1
4.4 3, 8.1
5.1 3, 8.1
5.2 3, 8.1
5.3 3, 8.1
6.1 1, 2, 3, 4, 7.1, 8.1 Testing for conformity according
to ISO 15883-1:—
6.2 3, 8.1
6.3 3, 8.1
7 9.1, 13.6
8 1, 3, 7.1, 7.2, 8.1
7.4, 8.2, 8.3, 8.4, 8.5, 8.6, 8.7, 10.1, 10.2, 10.3, not applicable
Clause 11, 12.2, 12.3, 12.4, 12.7.4, 12.8, 13.5,
- 12.1a) This relevant Essential
Requirement is not addressed in
this European Standard
4.1.1 13.3 a) This relevant Essential
Requirement is partly addressed
in this European Standard
- 13.6 q) This relevant Essential
Requirement is not addressed in
this European Standard
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the
scope of this standard.
For devices which are also machinery within the meaning of Article 2(a) of Directive 2006/42/EC on Machinery,
in accordance with Article 3 of Directive 93/42/EEC the following table ZA.2 details the relevant essential
requirements of Directive 2006/42/EC on Machinery to the extent to which they are more specific than those
of Directive 93/42/EEC along with the corresponding clauses of this European Standard. Table ZA.2,
however, does not imply any citation in the OJEU under the machinery directive and thus does not provide
presumption of conformity for the machinery directive.
Table ZA.2 – Relevant Essential Health and Safety Requirements from Directive 2006/42/EC on
machinery that are addressed by this European Standard
(according to article 3 of amended Directive 93/42/EEC)
Clause(s)/sub-clause(s) of this Essential Health and Safety Qualifying remarks/Notes
EN Requirements (EHSRs) of
Directive 2006/42/EC
4.1.1 1.1.7, 1.2.2, 1.2.3, 1.2.4, 1.2.5, This relevant EHSR are
1.3.2, 1.3.3, 1.3.4, 1.5.1, 1.5.2, addressed in this Standard
1.5.3, 1.5.5, 1.5.6, 1.5.8, 1.5.13,
1.5.14, 1.6.2, 1.6.3, 1.6.4, 1.6.5
4.1.1 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.6, This relevant EHSR are
1.3.1, 1.3.7, 1.3.8.1, 1.3.8.2, 1.5.4, partly addressed in this
1.6.1, 1.7.1, 1.7.2, ,1.7.3, 1.7.4 Standard
1.3.9, 1.4.1, 1.4.2, 1.4.3, 1.5.9, 4 This relevant EHSR are not
addressed in this Standard
INTERNATIONAL ISO
STANDARD 15883-2
First edition
2006-04-15
Washer-disinfectors —
Part 2:
Requirements and tests for washer-
disinfectors employing thermal
disinfection for surgical instruments,
anaesthetic equipment, bowls, dishes,
receivers, utensils, glassware, etc.
Laveurs désinfecteurs —
Partie 2: Exigences et essais pour laveurs désinfecteurs destinés à la
désinfection thermale des instruments chirurgicaux, du matériel
d'anesthésie, des récipients, des ustensiles et de la verrerie, etc.

Reference number
ISO 15883-2:2006(E)
©
ISO 2006
ISO 15883-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved

ISO 15883-2:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Performance requirements . 2
4.1 General. 2
4.2 Cleaning. 3
4.3 Disinfecting. 3
4.4 Temperature of internal surfaces of processed devices. 4
5 Mechanical and control requirements. 4
5.1 Load connectors . 4
5.2 Control systems. 5
5.3 Process verification. 5
6 Testing for conformity. 5
6.1 General. 5
6.2 Tests for soil removal from chamber walls, load carrier and load . 5
6.3 Thermometric tests.
...