CEN/TS 15427-1-3:2023
(Main)Railway applications - Wheel/rail friction management - Part 1-3: Equipment and application - Adhesion materials
Railway applications - Wheel/rail friction management - Part 1-3: Equipment and application - Adhesion materials
This document is limited to specifying the requirements when applying adhesion material to the interface between the wheel tread and the crown of the rail and includes both trainborne and trackside solutions.
This document only covers the equipment and application of adhesion material to the active interface.
This document defines:
- the characteristics that systems for the application of adhesion materials of the wheel-rail interface shall achieve, together with applicable inspection and test methods to be carried out for verification;
- all relevant terminology which is specific to the adhesion materials of the wheel-rail interface.
This document applies to the mainline railway.
NOTE 1 This document can also be used for other railways, e.g. urban rail.
NOTE 2 Where technologies are used to influence the wheel/rail interface, other than the application of an adhesion material, this document is out of scope but can be used as guidance.
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 1-3: Vorrichtungen und Anwendung - Kraftschlusserhöhende Materialien
Dieses Dokument beschränkt sich darauf, die Anforderungen bei der Anwendung von kraftschlusserhöhenden Materialien auf die Kontaktfläche zwischen Radlauffläche und Fahrfläche der Schiene festzulegen, und umfasst sowohl fahrzeugseitige als auch gleisseitige Lösungen.
Dieses Dokument deckt nur die Vorrichtungen und Anwendung von kraftschlusserhöhenden Materialien auf die aktive Kontaktfläche ab.
Dieses Dokument definiert
die Eigenschaften, die Systeme bei der Applikation von kraftschlusserhöhenden Materialien an der Kontaktfläche zwischen Rad und Schiene erfüllen müssen, zusammen mit geeigneten Inspektions- und Prüfverfahren, die zur Verifikation durchzuführen sind und
alle relevanten Begriffe, die spezifisch für kraftschlusserhöhenden Materialien für die Kontaktfläche zwischen Rad und Schiene sind.
Dieses Dokument ist für Vollbahnen anwendbar.
ANMERKUNG 1 Dieses Dokument kann auch für andere Schienennetze verwendet werden, z. B. städtische Schienenbahnen.
ANMERKUNG 2 Wo andere Technologien als die Anwendung eines kraftschlusserhöhenden Materials zur Beeinflussung der Kontaktfläche zwischen Rad und Schiene verwendet werden, liegen diese nicht im Anwendungsbereich dieses Dokuments, es kann jedoch als Leitlinie verwendet werden.
Applications ferroviaries - Gestion du frottement roue/rail - Partie 1-3 : Équipement et application - Matériau d'adhésion
Železniške naprave - Trenje na stiku kolo-tirnica - 1-3. del: Oprema in uporaba - Lepilni materiali
Ta dokument je omejen na določanje zahtev pri nanašanju lepilnih materialov na vmesnik med kolesnim obročem in zgornjim robom tirnice ter vključuje opremo tako na vlaku kot ob progi.
Dokument zajema le opremo in uporabo lepilnega materiala na aktivnem vmesniku.
Ta dokument določa:
– značilnosti, ki jih morajo doseči sistemi za nanašanje lepilnih materialov vmesnika med kolesom in tirnico, ter ustrezne metode za pregled in preskušanje, ki jih je treba izvesti za preverjanje;
– vso ustrezno terminologijo v zvezi z lepilnimi materiali vmesnika med kolesom in tirnico.
Ta dokument se uporablja za glavne železniške proge.
OPOMBA 1: Ta dokument je mogoče uporabiti tudi za druge železniške proge (npr. mestna železnica).
OPOMBA 2: Ta dokument ne zajema uporabe tehnologij, ki vplivajo na vmesnik med kolesom in tirnico (razen nanosa lepilnega materiala), vendar ga je mogoče uporabiti kot vodilo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2023
Nadomešča:
SIST-TS CEN/TS 15427-1-3:2021
Železniške naprave - Trenje na stiku kolo-tirnica - 1-3. del: Oprema in uporaba -
Lepilni materiali
Railway applications - Wheel/rail friction management - Part 1-3: Equipment and
application - Adhesion materials
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 1-3:
Vorrichtungen und Anwendung - Kraftschlusserhöhende Materialien
Applications ferroviaries - Gestion du frottement roue/rail - Partie 1-3 : Équipement et
application - Matériau d'adhésion
Ta slovenski standard je istoveten z: CEN/TS 15427-1-3:2023
ICS:
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 15427-1-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
October 2023
TECHNISCHE SPEZIFIKATION
ICS 45.040 Supersedes CEN/TS 15427-1-3:2021
English Version
Railway applications - Wheel/Rail Friction Management -
Part 1-3: Equipment and Application - Adhesion Materials
Applications ferroviaries - Gestion du frottement Bahnanwendungen - Reibungsmanagement zwischen
roue/rail - Partie 1-3 : Équipement et application - Rad und Schiene - Teil 1-3: Vorrichtungen und
Matériau d'adhésion Anwendung - Kraftschlusserhöhende Materialien
This Technical Specification (CEN/TS) was approved by CEN on 30 August 2023 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15427-1-3:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General . 8
4.1 Purpose . 8
4.2 Application . 9
5 Requirements for trainborne equipment . 9
5.1 General . 9
5.2 Design of trainborne equipment . 10
5.3 Installation of trainborne equipment . 10
5.4 Operations, inspection and maintenance . 11
5.5 Application . 11
5.6 Verification . 12
6 Requirements for trackside equipment . 12
6.1 General . 12
6.2 Design of trackside equipment . 13
6.3 Installation of trackside equipment . 14
6.4 Operation, inspection and maintenance . 14
6.5 Application . 14
6.6 Verification . 15
Annex A (informative) Types of trainborne equipment. 16
A.1 Introduction . 16
A.2 Trainborne equipment - Sand application to the active interface . 16
A.3 Trackside equipment - applicator for traction gels . 18
Annex B (informative) Guidance on approvals testing and verification . 19
B.1 General . 19
B.2 Trials . 20
B.2.1 General . 20
B.2.2 Monitoring . 20
B.2.3 Outcome of trial . 20
Annex C (informative) Guideline braking tests for adhesion materials (trainborne and
trackside equipment) . 21
C.1 General . 21
C.2 Choosing the right test vehicle: . 21
C.3 Trainborne equipment . 21
C.4 Test track . 22
C.5 Test conditions . 22
C.6 Conducted tests . 22
C.7 Testing proactive adhesion material . 22
C.7.1 Test purpose . 22
C.7.2 Test procedure . 22
C.7.3 Test cases . 22
C.7.4 Application adhesion material . 23
C.7.5 Assessment criterion . 23
C.8 Testing reactive adhesion material: . 23
C.8.1 Test purpose . 23
C.8.2 Reference braking distance . 23
C.8.3 Application adhesion material . 23
C.8.4 Point of braking . 23
C.8.5 Assessment criterion . 23
C.9 Effect on brake blocks and magnetic track brakes . 23
C.10 Application efficiency of adhesion material . 24
C.10.1 General . 24
C.10.2 Purpose . 24
C.10.3 Angle of nozzle for adhesion materials without adhesive properties . 24
Bibliography . 26
European foreword
This document (CEN/TS 15427-1-3:2023) has been prepared by Technical Committee CEN/TC 256
“Railway applications”, the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 15427-1-3:2021.
CEN/TS 15427-1-3:2021:
— document has been editorially updated based on the feedback received on the previous edition;
— corrections and clarifications have been introduced based on the feedback received on the previous
edition;
— consistency with the other parts of the series has been improved.
This document is part of the following series:
— EN 15427-1-1, Railway applications - Wheel/Rail friction management - Part 1-1: Equipment and
Application – Flange lubrication;
— CEN/TS 15427-1-2, Railway applications - Wheel/rail friction management - Part 1-2: Equipment and
application – Top of rail materials;
— CEN/TS 15427-1-3, Railway applications - Wheel/rail friction management - Part 1-3: Equipment and
application – Adhesion materials;
— EN 15427-2-1, Railway applications - Wheel/Rail friction management - Part 2-1: Properties and
Characteristics – Flange lubricants;
— CEN/TS 15427-2-2, Railway applications - Wheel/rail friction management - Part 2-2: Properties and
characteristics – Top of rail materials;
— CEN/TS 15427-2-3, Railway applications - Wheel/Rail friction management - Part 2-3: Properties and
Characteristics – Adhesion materials;
— CEN/prTR 15427-3, Railway applications – Wheel/Rail friction management – Part 3: Rationale for
requirements and further background information.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.