EN 17020-3:2022

SLOVENSKI STANDARD
01-april-2023
Razširjena uporaba rezultatov preskusov trajnosti samozapiranja za požarno
odporna in/ali dimotesna vrata in okna, ki se odpirajo - 3. del: Trajnost
samozapiranja jeklenih drsnih vrat
Extended application of test results on durability of self-closing for fire resistance and/or
smoke control doorsets and openable windows - Part 3: Durability of self-closing of steel
sliding doorsets
Erweiterter Anwendungsbereich von Prüfergebnissen zur Dauerhaftigkeit der
Selbstschließung für Feuerschutz- und/oder Rauchschutztüren und zu öffnende Fenster
- Teil 3: Dauerhaftigkeit der Selbstschließung von Schiebetoren aus Stahl
Application étendue des résultats d’essais de durabilité de la fermeture automatique des
blocs-portes et fenêtres ouvrantes résistants au feu et/ou étanches à la fumée - Partie 3
: Durabilité de la fermeture automatique des blocs-portes coulissants en acier
Ta slovenski standard je istoveten z: EN 17020-3:2022
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
91.060.50 Vrata in okna Doors and windows
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17020-3
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 13.220.50; 91.060.50
English Version
Extended application of test results on durability of self-
closing for fire resistance and/or smoke control doorsets
and openable windows - Part 3: Durability of self-closing
of steel sliding doorsets
Application étendue des résultats d'essais de durabilité Erweiterter Anwendungsbereich von Prüfergebnissen
de la fermeture automatique des blocs-portes et zur Dauerhaftigkeit der Selbstschließung für
fenêtres ouvrantes résistants au feu et/ou étanches à la Feuerschutz- und/oder Rauchschutztüren und zu
fumée - Partie 3 : Durabilité de la fermeture öffnende Fenster - Teil 3: Dauerhaftigkeit der
automatique des blocs-portes coulissants en acier Selbstschließung von Schiebetoren aus Stahl
This European Standard was approved by CEN on 24 July 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17020-3:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Determination of the field of extended application . 8
4.1 General . 8
4.2 Procedure for evaluation . 8
4.3 Procedure for maximum field of extended application . 9
4.4 Interpretation of test results . 9
5 Extended application report . 10
6 Classification report . 10
Annex A (normative) Construction parameter variations . 11
Annex B (normative) Construction parameter variation simulation by applying additional
weights . 59
Bibliography . 60

European foreword
This document (EN 17020-3:2022) has been prepared by Technical Committee CEN/TC 127 “Fire safety
in buildings”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association.
A list of all parts in the EN 17020 series and the EN 15269 series can be found on the CEN website.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
The EN 15269 series of standards covering extended application of test results for fire resistance and/or
smoke control for doorsets, shutter assemblies and openable window, including their items of building
hardware, does not yet include the durability of self-closing following an extended application process.
This document is one of the EN 17020 series of standards intended to be used for the purpose of
producing an extended application report based on the evaluation of one or more durability of self-
closing tests. These European Standards may also be used to identify the best selection of test specimens
required to cover a wide range of product variations.
1 Scope
This document is applicable to the following types of steel based doorsets: horizontally sliding single and
double leaf doorsets, horizontally sliding single and double leaf telescopic doorsets, vertically sliding
single leaf doorsets and vertically sliding single leaf telescopic doorsets as covered by EN 15269-7 or
EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from
durability of self-closing test(s) conducted in accordance with EN 12605:2000 and/or EN 1191.
Subject to the completion of the appropriate durability of self-closing test or tests, the extended
application can cover all or some of the following non-exhaustive list:
— door leaf (of the sliding doorset and its pass door);
— integrated pass doors;
— wall or ceiling fixed parts or items of the doorset, e.g. frame or suspension systems;
— ventilation grilles and/or louvres;
— glazing for door leaf;
— items of building hardware;
— decorative finishes;
— intumescent, smoke, draught or acoustic seals;
— alternative supporting construction(s).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 179, Building hardware - Emergency exit devices operated by a lever handle or push pad, for use on
escape routes - Requirements and test methods
EN 1125, Building hardware - Panic exit devices operated by a horizontal bar, for use on escape routes -
Requirements and test methods
EN 1154, Building hardware - Controlled door closing devices - Requirements and test methods
EN 1155, Building hardware - Electrically powered hold-open devices for swing doors - Requirements and
test methods
EN 1191, Windows and doors - Resistance to repeated opening and closing - Test method
EN 1363-1, Fire resistance tests - Part 1: General requirements
EN 1363-2, Fire resistance tests - Part 2: Alternative and additional procedures
EN 14637, Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies -
Requirements, test methods, application and maintenance
EN 1634-1, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 1: Fire resistance test for door and shutter assemblies and openable
windows
EN 1634-3, Fire resistance and smoke control tests for door and shutter assemblies, openable windows and
elements of building hardware - Part 3: Smoke control test for door and shutter assemblies
EN 1906, Building hardware - Lever handles and knob furniture - Requirements and test methods
EN 1935:2002 , Building hardware - Single-axis hinges - Requirements and test methods
EN 12209, Building hardware - Mechanically operated locks and locking plates - Requirements and test
methods
EN 12433-1, Industrial, commercial and garage doors and gates - Terminology - Part 1: Types of doors
EN 12433-2, Industrial, commercial and garage doors and gates - Terminology - Part 2: Parts of doors
EN 12605:2000, Industrial, commercial and garage doors and gates - Mechanical aspects - Test methods
EN 13501-1, Fire classification of construction products and building elements - Part 1: Classification using
data from reaction to fire tests
EN 13501-2, Fire classification of construction products and building elements - Part 2: Classification using
data from fire resistance tests, excluding ventilation services
EN 14846, Building hardware - Locks and latches - Electromechanically operated locks and striking plates -
Requirements and test methods
EN 15269-1, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 1: General
requirements
EN 15269-7, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 7: Fire resistance for
steel sliding doorsets
EN 15269-20, Extended application of test results for fire resistance and/or smoke control for door, shutter
and openable window assemblies, including their elements of building hardware - Part 20: Smoke control
for doors, shutters, operable fabric curtains and openable windows
, Building hardware - Requirements and test methods - Multipoint locks, latches and locking
EN 15685
plates - Characteristics and test methods
EN ISO 13943, Fire safety - Vocabulary (ISO 13943)

As impacted by EN 1935:2002/AC:2003.
Under preparation. Stage at the time of publication: prEN 15685:2022.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1191, EN 1363-1, EN 1363-2,
EN 1634-1, EN 1634-3, EN 15269-1, EN 15269-7, EN 15269-20, EN 12433-1, EN 12433-2 and
EN ISO 13943 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
full scale test
test of a full size doorset in accordance with EN 12605:2000 and/or EN 1191
3.2
panel
part of a leaf or element of a doorset as indicated as 1 in Figures 1 and 2

Key
1 panel
2 leaf
3 element
Figure 1 — Double leaf telescopic sliding doorset

Key
1 panel
2 leaf
Figure 2 — Double leaf sliding doorset
3.3
leaf
movable part of a doorset indicated as 2 in Figures 1 and 2
...