prEN 10340-2
(Main)Steel castings for structural uses - Part 2: Technical delivery conditions
Steel castings for structural uses - Part 2: Technical delivery conditions
This Part of prEN 10340, in addition to Part 1, specifies technical delivery conditions for steel castings for structural uses in buildings and civil engineering works.
In cases where castings are joined by welding by the founder, this Part of prEN 10340 applies.
This Part does not apply in cases where castings are welded:
- to wrought products (plates, tubes, forgings...); or
- by non-founders.
Stahlguss für das Bauwesen - Teil 2: Technische Lieferbedingungen
prEN 10340-2 regelt neben prEN 10340-1 auch die technischen Lieferbedingungen für Stahlgussteile für den Hoch- und Tiefbau.
In Fällen, in denen Gussteile durch Schweißen durch den Gießer zusammengefügt werden, gilt prEN 10340-2.
prEN 10340-2 gilt nicht in Fällen, in denen Gussstücke geschweißt werden:
- zusammen mit umformbaren Erzeugnissen (Bleche, Rohre, Schmiedestücke, usw.); oder
- von anderen als Gießern.
Aciers moulés de construction - Partie 2 : Conditions techniques de livraison
Le prEN 10340-2, en complément au prEN 10340-1, spécifie les conditions techniques de livraison des pièces moulées en acier destinées à des utilisations structurales dans le bâtiment et le génie civil.
Dans le cas où les pièces moulées sont assemblées par soudage par le fondeur, le prEN 10340-2 s’applique.
Le prEN 10340-2 ne s'applique pas dans les cas où les pièces moulées sont soudées :
- à des produits corroyés (plaques, tubes, pièces forgées, etc.) ; ou
- par des non-fondeurs.
Jekleni ulitki za uporabo v gradbeništvu - 2. del: Tehnični dobavni pogoji
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 10340-2:2017
01-april-2017
-HNOHQLXOLWNL]DXSRUDERYJUDGEHQLãWYXGHO 7HKQLþQLGREDYQLSRJRML
Steel castings for structural uses - Part 2: Technical delivery conditions
Stahlguss für das Bauwesen - Teil 2: Technische Lieferbedingungen
Aciers moulés de construction - Partie 2: Conditions techniques de livraison
Ta slovenski standard je istoveten z: prEN 10340-2
ICS:
77.140.80 Železni in jekleni ulitki Iron and steel castings
oSIST prEN 10340-2:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10340-2:2017
---------------------- Page: 2 ----------------------
oSIST prEN 10340-2:2017
DRAFT
EUROPEAN STANDARD
prEN 10340-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2017
ICS 77.140.80 Will supersede EN 10340:2007
English Version
Steel castings for structural uses - Part 2: Technical
delivery conditions
Aciers moulés de construction - Partie 2: Conditions Stahlguss für das Bauwesen - Teil 2: Technische
techniques de livraison Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
ECISS/TC 111.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10340-2:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10340-2:2017
prEN 10340-2:2017 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Information to be supplied by the purchaser . 4
4.1 Mandatory information . 4
4.2 Optional information . 5
5 Designation. 5
6 Manufacture . 5
6.1 Manufacturing process . 5
6.2 Welding operations . 5
7 Requirements .
...
SLOVENSKI STANDARD
oSIST prEN 10340-2:2019
01-julij-2019
Jekleni ulitki za uporabo v gradbeništvu - 2. del: Tehnični dobavni pogoji
Steel castings for structural uses - Part 2: Technical delivery conditions
Stahlguss für das Bauwesen - Teil 2: Technische Lieferbedingungen
Aciers moulés de construction - Partie 2: Conditions techniques de livraison
Ta slovenski standard je istoveten z: prEN 10340-2
ICS:
77.140.80 Železni in jekleni ulitki Iron and steel castings
oSIST prEN 10340-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10340-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN 10340-2:2019
DRAFT
EUROPEAN STANDARD
prEN 10340-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2019
ICS 77.140.80 Will supersede EN 10340:2007
English Version
Steel castings for structural uses - Part 2: Technical
delivery conditions
Aciers moulés de construction - Partie 2: Conditions Stahlguss für das Bauwesen - Teil 2: Technische
techniques de livraison Lieferbedingungen
This draft European Standard is submitted to CEN members for second enquiry. It has been drawn up by the Technical
Committee CEN/TC 459/SC 11.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10340-2:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10340-2:2019
prEN 10340-2:2019 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Information to be supplied by the purchaser . 6
4.1 Mandatory information . 6
4.2 Optional information . 6
5 Designation. 6
6 Manufacture . 6
6.1 Manufacturing process . 6
6.1.1 Melting . 6
6.1.2 Heat treatment .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.