EN 10263-2:2001

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SUHGHODYLWalzdraht, Stäbe und Draht aus Kaltstauch- und Kaltfließpressstählen - Teil 2: Technische Lieferbedingungen für nicht für eine Wärmebehandlung nach der Kaltverarbeitung vorgesehene StähleBarres, fil machine et fils en acier pour transformation a froid et extrusion a froid - Partie 2: Conditions techniques de livraison des aciers n'étant pas destinés a un traitement thermique apres travail a froidSteel rod, bars and wire for cold heading and cold extrusion - Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains77.140.60Jeklene palice in drogoviSteel bars and rodsICS:Ta slovenski standard je istoveten z:EN 10263-2:2001SIST EN 10263-2:2002en01-september-2002SIST EN 10263-2:2002SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10263-2June 2001ICS 77.140.60; 77.140.65English versionSteel rod, bars and wire for cold heading and cold extrusion -Part 2: Technical delivery conditions for steels not intended forheat treatment after cold workingBarres, fil machine et fils en acier pour transformation àfroid et extrusion à froid - Partie 2: Conditions techniquesde livraison des aciers n'étant pas destinés à un traitementthermique après travail à froidWalzdraht, Stäbe und Draht aus Kaltstauch- undKaltfließpreßstählen - Teil 2: Technische Lieferbedingungenfür nicht für eine Wärmebehandlung nach derKaltverarbeitung vorgesehene StähleThis European Standard was approved by CEN on 19 April 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10263-2:2001 ESIST EN 10263-2:2002

Page 2EN 10263-2:2001C O N T E N T SFOREWORD.31Scope.32Normative references.33Terms and definitions.34Classification and designation.44.1Classification.44.2Designation.45Production process.45.1General.45.2Deoxidation.46Requirements.46.1Delivery condition.46.2Chemical composition.46.3Mechanical properties.46.4Surface quality.46.5Supplementary or special requirements.4SIST EN 10263-2:2002

Page 3EN 10263-2:2001FOREWORDThis European Standard has been prepared by Technical Committee ECISS/TC 15 "Wire-rod- Qualities, dimensions, tolerances and specific tests", the secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publicationof an identical text or by endorsement, at the latest by December 2001, and conflictingnational standards shall be withdrawn at the latest by December 2001.This European Standard EN 10263 is subdivided as follows:- Part 1:General technical delivery conditions;- Part 2:Technical delivery conditions for steels not intended for heat treatment after coldworking;- Part 3:Technical delivery conditions for case hardening steels;- Part 4:Technical delivery conditions for steels for quenching and tempering- Part 5:Technical delivery conditions for stainless steels.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.1Scope1.1This Part of EN 10263 is applicable to round rod and bars and wire with a diameter upto and including 100 mm, of non-alloy and alloy steel, intended for cold heading and coldextrusion without subsequent heat treatment on the final components.1.2This Part of EN 10263 is complemented by EN 10263-1.2Normative referencesThis European Standard inco
...