iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1917:2002

(Main)

Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

This European Standard specifies performance requirements as defined in table 1 and describes test methods for precast concrete units, including joints (elastomeric, plastomeric or other sealing materials, either integrated in the unit or supplied separately), for inspection chambers designed to be used for inverts not exceeding 2 metres deep and manholes, of circular, rectangular (with or without chamfered or rounded corners) or elliptical internal shape, unreinforced, steel fibre and reinforced, with nominal sizes not exceeding DN 1250 for units with a circular bore or LN 1250 for units with a rectangular or elliptical shape.

Einsteig- und Kontrollschächte aus Beton, Stahlfaserbeton und Stahlbeton

Diese Europäische Norm legt Leistungsanforderungen, wie in Tabelle 1 angegeben, fest und beschreibt Prüfverfahren für vorgefertigte Bauteile, für Kontrollschächte, die nicht tiefer als 2 m sind, und für Einsteigschächte mit kreisrundem, rechteckigem (mit oder ohne abgeschrägte oder abgerundete Ecken) oder elliptischem Querschnitt aus unbewehrtem Beton, Stahlfaser- und Stahlbeton, mit Nennweiten und Nennlängen nicht über DN 1250 (rund) oder LN 1250 (rechteckig oder elliptisch). Die Schächte sollen den Zugang und die Luftzufuhr zu Entwässerungssystemen ermöglichen, die für den Transport von Abwasser, Regenwasser und Oberflächenwasser als Freispiegelleitungen oder gelegentlich unter geringem Überdruck verwendet werden und hauptsächlich in Gebieten mit Fahrzeug- und/oder Fußgängerverkehr eingebaut werden. Anforderungen an Verbindungen (elastomere, plastomere oder andere Dichtmittel, entweder im Bauteil eingebaut oder getrennt mitgeliefert) werden ebenfalls festgelegt.
Festlegungen für die Beurteilung der Konformität und für die Kennzeichnung von Bauteilen nach dieser Europäischen Norm sind enthalten.

Regards de visite et boîtes de branchement ou d'inspection en béton non armé, béton fibré acier et béton armé

La présente Norme européenne spécifie les exigences de performance définies au Tableau 1 et décrit les méthodes d'essai relatives aux éléments préfabriqués en béton pour les boîtes de branchement ou d'inspection conçues pour avoir un fil d'eau qui ne soit pas à plus de 2 m de profondeur et les regards de visite de section intérieure circulaire, rectangulaire (comportant ou non des angles chanfreinés ou arrondis) ou encore elliptique, en béton non armé, béton acier fibré et béton armé, dont les dimensions nominales et les longueurs nominales ne dépassent pas DN 1 250 (dans le cas des éléments de section intérieure circulaire), ou LN 1 250 (dans le cas des éléments de section intérieure rectangulaire ou elliptique). Ces éléments sont principalement destinés à permettre, outre leur aération, l'accès aux réseaux d'évacuation ou d'assainissement véhiculant des eaux usées, des eaux pluviales et des eaux de surface par écoulement gravitaire ou, occasionnellement, sous faible pression, installés dans des zones soumises à une circulation routière et/ou piétonne. Des exigences relatives aux garnitures d'étanchéité (en élastomères, plastomères ou autres matériaux d'étanchéité, soit intégrées à l'élément, soit fournies séparément) sont également spécifiées.
Elle précise les modalités d'évaluation de la conformité des éléments à la présente Norme européenne.
Les conditions de marquage sont incluses.
Tableau 1 - Caractéristiques spécifiées et exclusions
Caractéristique   Exclusions
Matériaux   -   spécifications de référence dans le cas où les normes européennes correspondantes n'ont pas encore été publiées ;
-   toute classification des échelons pour deux pieds.
Béton   Nature et valeur(s) du dosage minimal en ciment plus additions pouzzolaniques ou hydrauliques, quelles qu'elles soient, selon les conditions d'emploi du produit.
Aspect de surface   Limitation de la taille des irrégularités de surface.
Caractéristiques géométriques   -   dimensions nominales ;
-   dimensions intérieures

Betonski vstopni in revizijski jaški, nearmirani, z jeklenimi vlakni in armirani

General Information

Status
Published
Publication Date
22-Oct-2002
ICS
93.030 - External sewage systems
Technical Committee
CEN/TC 165 - Waste water engineering
Drafting Committee
CEN/TC 165/WG 9 - Concrete pipes
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
09-Jun-2022
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/118 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on waste water engineering products
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 1917:2003 - Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

Relations

Corrected By
EN 1917:2002/AC:2008 - Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced
Effective Date
22-Dec-2008
Corrected By
EN 1917:2002/AC:2003 - Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced
Effective Date
22-Dec-2008
Corrected By
EN 1917:2002/AC:2006 - Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced
Effective Date
22-Dec-2008

Buy Standard

EN 1917:2003EN 1917:2003
PreviousNext
Standard
EN 1917:2003
English language
75 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Betonski vstopni in revizijski jaški, nearmirani, z jeklenimi vlakni in armiraniEinsteig- und Kontrollschächte aus Beton, Stahlfaserbeton und StahlbetonRegards de visite et boîtes de branchement ou d'inspection en béton non armé, béton fibré acier et béton arméConcrete manholes and inspection chambers, unreinforced, steel fibre and reinforced93.030Zunanji sistemi za odpadno vodoExternal sewage systemsICS:Ta slovenski standard je istoveten z:EN 1917:2002SIST EN 1917:2003en01-marec-2003SIST EN 1917:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1917October 2002ICS 93.030English versionConcrete manholes and inspection chambers, unreinforced,steel fibre and reinforcedRegards de visite et boîtes de branchement en béton nonarmé, béton fibré acier et béton arméEinsteig- und Kontrollschächte aus Beton, Stahlfaserbetonund StahlbetonThis European Standard was approved by CEN on 18 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1917:2002 ESIST EN 1917:2003

Test method for crushing strength of chamber and shaft units.29A.1Principle.29A.2Apparatus.29A.3Preparation.29A.4Procedure.29A.4.1Horizontal arrangement.29A.4.2Vertical arrangement.30A.4.3General.32A.5Expression of results.32Annex B (normative)
Test methods for vertical strength of reducing units and capping units.33B.1Principle.33B.2Apparatus.33B.3Preparation.33B.4Procedure.33B.4.1Unreinforced and steel fibre concrete units.33B.4.2Reinforced concrete units.33B.5Expression of results.36B.5.1Vertical crushing load tests.36B.5.2Vertical proof load tests.36Annex C (normative)
Test methods for watertightness.37C.1Principle.3
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 11296-9:2022(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
SIST EN ISO 11296-9:2023

This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system.
NOTE      Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12889:2022(Main)
Trenchless construction and testing of drains and sewers
SIST EN 12889:2023

This document is applicable to the trenchless construction, trenchless replacement techniques and testing of new drains and new sewers in the ground and usually operating as gravity or pressure pipelines, formed using prefabricated pipes and their joints.
Renovation techniques for existing pressure and non-pressure systems are not covered by this document.
Methods of trenchless construction include:
- manned and unmanned techniques;
- steerable and non-steerable techniques.
NOTE 1 Mining or tunnelling techniques for permanent structures (e.g. in situ construction or the use of prefabricated segments) are not covered by this document although some parts can apply to these methods.
NOTE 2 Trenchless insertion using a pipe plough system is a common method for installing small pipes and cables. The method does not exactly cope with the scope of this document. Therefore, it is described in the informative Annex D.
Requirements for associated pipeline installation work other than trenchless construction, e.g. for manholes and inspection chambers, are not covered by this document and are specified in EN 1610. This also applies to pipes that are subsequently installed within entry and exit shafts/pits.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 476:2022(Main)
General requirements for components used in drains and sewers
SIST EN 476:2022

This document specifies general requirements to be respected in product standards for components such as pipes, fittings, inspection chambers and manholes with their respective joints intended for use in drains and sewers inside and outside buildings which operate as gravity systems allowing for a maximum pressure of 40 kPa.
It also specifies general requirements for components used in hydraulically and pneumatically pressurized pipes, drains and sewers.
NOTE 1   Where the term “inside buildings” is used in the context of components fixed inside buildings, it also includes pipes and fittings fixed on external surfaces of buildings.
NOTE 2   This document is not a product standard and therefore not intended for the direct evaluation of products.
This document covers components to be used in conveying in a satisfactory manner:
—   domestic wastewater;
—   rainwater and surface water;
—   other wastewater acceptable for discharge into the system.
This document is applicable to components of circular and other cross sections.
This document is equally applicable to components which are factory-made and to those constructed on site, where applicable.
NOTE 3   This document does not apply to components used for trenchless construction according to EN 14457 and for components used for renovation of drains and sewers according to EN 13380.
This document does not supersede the functional requirements of a complete system as defined in EN 752.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16933-1:2022(Main)
Drain and sewer systems outside buildings - Design - Part 1: Layout principles
SIST EN 16933-1:2022

This document specifies requirements for the design of drain and sewer systems outside buildings.
It is applicable to drain and sewer systems from the point where the wastewater leaves a building, roof drainage system, or paved area, to a point where it is discharged into a wastewater treatment plant or receiving water body.
This document specifies requirements for the layout of drain and sewer systems.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14654-3:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 3: Drain and sewer cleaning
SIST EN 14654-3:2021

This document establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers the management and control of drain and sewer cleaning.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14654-4:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 4: Control of inputs from users
SIST EN 14654-4:2021

This document establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document together with EN 14654-1:2021 covers the control of inputs from users.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14654-1:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 1: General requirements
SIST EN 14654-1:2021

This document establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers general requirements for the management and control of activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14654-2:2021(Main)
Drain and sewer systems outside buildings - Management and control of activities - Part 2: Rehabilitation
SIST EN 14654-2:2021

This document establishes requirements for the management and control of activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques.
This document covers the management and control of rehabilitation activities.
It is applicable to drain and sewer systems from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water body.
Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15885:2018(Main)
Classification and characteristics of techniques for renovation, repair and replacement of drains and sewers
SIST EN 15885:2019

This European Standard specifies a system for the classification of trenchless techniques for renovation, repair and replacement on the same line of drains and sewers outside buildings, operated under gravity or pressure, including pipes, connections and manholes. It defines and describes families of techniques and their different generic methods and materials used.
This European Standard does not apply for replacement by open trenching according to EN 1610 and trenchless construction and testing of drains and sewers as new construction off-the-line of the existing drain or sewer according to EN 12889.
This European Standard does not apply for the specification of requirements for specific products.
For each technique family it lists relevant existing standards, materials and applications and outlines characteristics including installation aspects, structural and hydraulic capabilities and site impact.
This standard does not apply to any work required on the existing pipe prior to renovation, repair or replacement.
This European Standard provides information needed to determine viable options and for identification of the optimal technique with regard to a given set of renovation, repair or replacement objectives.
NOTE It is the responsibility of the designer to choose and design the renovation, replacement and repair systems.
It does not specify the calculation methods to determine, for each viable technique, the required amount of material needed to secure the desired performance of the pipeline to be rehabilitated.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16932-2:2018(Main)
Drain and sewer systems outside buildings - Pumping systems - Part 2: Positive pressure systems
SIST EN 16932-2:2018

This European Standard specifies requirements for design, construction and acceptance testing of wastewater pumping systems in drain and sewer systems outside the buildings they are intended to serve. It includes pumping systems in drain and sewer systems that operate essentially under gravity as well as systems using either positive pressure or partial vacuum.
This document is applicable to positive pressure systems.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day