iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13063-1:2005

(Main)

Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

This European Standard specifies the requirements and test methods for multiwall soot fire resistant system chimneys, working under dry conditions, with corrosion resistance 3, with negative pressure (see EN 1443) in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking and inspection are also covered by this standard.
This standard does not apply to structurally independent (free standing or self supporting) system chimneys.
A soot fire resistant system chimney has the following items where appropriate:
-   clay/ceramic flue liners;
-   Insulation layer;
-   outer walls;
-   mortar for jointing flue liners;
-   mortar for jointing outer walls;
-   terminal;
-   chimney base;
-   cladding;
-   opening section;
-   cleaning and inspection door;
-   distance piece;
-   reinforcement.
The soot fire resistant chimney covers a combination of compatible chimney components, obtained or specified from one manufacturing source with product responsibility for the whole chimney.

Abgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 1: Anforderungen und Prüfungen für Rußbrandbeständigkeit

Diese Norm legt die Anforderungen und Prüfungen für mehrschalige rußbrandbeständige System-Abgasanlagen, die für trockene Betriebsweise, Korrosionswiderstandsklasse 3, die Druckklasse N 1 oder N 2 (siehe EN 1443) in denen die Verbrennungsprodukte über Keramik-Innenrohre an die Außenluft abgeleitet werden, fest. Die Norm beinhaltet auch Angaben zur Kennzeichnung und Inspektion.
Die Norm gilt nicht für konstruktionsmäßig unabhängige (freistehend oder selbsttragend) System-Abgasanlagen.
Eine System-Abgasanlage hat die folgende Bauteile, falls zuteffend:
-   Keramik-Innenrohre;
-   Dämmschicht;
-   Außenschalen;
-   Mörtel für das Verfugen der Innenrohre;
-   Mörtel für das Verfugen der Außenschalen;
-   Aufsätze;
-   Sockelabschnitt;
-   Verkleidung;
-   Reinigungsabschnitt;
-   Reinigungs- und Inspektionsöffnungen;
-   Abstandshalter;
-   Bewehrung.
Die rußbrandbeständige System-Abgasanlage setzt sich aus aufeinander abgestimmten Komponenten zusammen, die von einem Hersteller stammen oder von diesem bestimmt wurden, wobei dieser die Produkthaftung für die gesamte Abgasanlage übernimmt.

Conduits de fumées - Conduits-systémes avec conduit intérieur en terre cuite/céramique - Partie 1: Exigences et méthodes d'essai relatives à la détermination de la résistance au feu de cheminée

La présente Norme européenne spécifie les exigences et les méthodes d'essai applicables aux conduits-systèmes multienveloppes résistant au feu de cheminée, fonctionnant en condition sèche, avec une classe de résistance à la corrosion de 3, en pression négative (voir EN 1443), dans lesquels les produits de combustion sont acheminés vers l'atmosphère via des conduits intérieurs en terre cuite/céramique. La présente norme concerne également le marquage et le contrôle.
La présente norme ne s'applique pas aux conduits-systèmes structurellement indépendants (autoporteurs ou autonomes).
Un conduit-système résistant au feu de cheminée se compose des éléments suivants, selon le cas :
-   un conduit intérieur en terre cuite/céramique ;
-   une couche d'isolant ;
-   des enveloppes extérieures ;
-   du mortier pour jointoyer les conduits intérieurs ;
-   du mortier pour jointoyer les enveloppes extérieures ;
-   un terminal ;
-   une base ;
-   un habillage ;
-   une ouverture ;
-               une trappe de nettoyage et de visite ;
-   une entretoise ;
-   une armature.
Le conduit de fumée résistant au feu de cheminée englobe un ensemble d'éléments compatibles, fournis ou conseillés par un fabricant assumant la responsabilité du produit pour le conduit de fumée dans son intégralité.

Dimniki - Sistemski dimniki s keramičnimi tuljavami - 1. del: Zahteve za odpornost proti požaru saj in preskusne metode

General Information

Status
Withdrawn
Publication Date
13-Dec-2005
Withdrawal Date
17-Jul-2007
ICS
91.060.40 - Chimneys, shafts, ducts
Technical Committee
CEN/TC 166 - Chimneys
Drafting Committee
CEN/TC 166 - Chimneys
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Jul-2007
Completion Date
18-Jul-2007
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/105 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on chimneys, flues and specific products
Ref Project
SIST EN 13063-1:2006 - Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

Relations

Merged Into
EN 13063-1:2005+A1:2007 - Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance
Effective Date
22-Dec-2008

Buy Standard

EN 13063-1:2006EN 13063-1:2006
PreviousNext
Standard
EN 13063-1:2006
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
EN 13063-1:2006EN 13063-1:2006
PreviousNext
Standard
EN 13063-1:2006
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistanceConduits de fumées - Conduits-systémes avec conduit intérieur en terre cuite/céramique - Partie 1: Exigences et méthodes d'essai relatives a la détermination de la résistance au feu de cheminéeAbgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 1: Anforderungen und Prüfungen für RußbrandbeständigkeitTa slovenski standard je istoveten z:EN 13063-1:2005SIST EN 13063-1:2006en91.060.40Dimniki, jaški, kanaliChimneys, shafts, ductsICS:SLOVENSKI
STANDARDSIST EN 13063-1:200601-maj-2006

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13063-1December 2005ICS 91.060.40 English VersionChimneys - System chimneys with clay/ceramic flue liners - Part1: Requirements and test methods for sootfire resistanceConduits de fumées - Conduits-systémes avec conduitintérieur en terre cuite/céramique résistant au feu decheminée - Partie 1: Exigences et méthodes d'essaiAbgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 1: Anforderungen und Prüfungen fürRußbrandbeständigkeitThis European Standard was approved by CEN on 2 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13063-1:2005: E

Test methods.18 Annex B (normative)
Stainless steel outer walls.24 Annex C (normative)
Thermal resistance of the system chimney.25 Annex D (normative)
Sampling procedures for an AQL of 10 % and inspection level S2.26 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Product Directive.30 Bibliography.37

3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 1443:2003 and
EN 13216-1:2004 and the following apply. 3.1 soot fire resistant multiwall system chimney multiwall construction, consisting mainly of an outer wall, an insulation layer and a sootfire resistant inner clay/ceramic flue liner. The combination of these components forms a sootfire resistant system chimney (see Figure 1)

Key 1 Inner liner 2 Insulation layer 3 Outer wall 4 Cavities for back ventilation 5 Cavities for structural reinforcement Figure 1 – Construction of a soot fire resistant system chimney 3.2 chimney base section of the system chimney, situated at the bottom, which comprises an inspection opening with door 3.3 reinforced outer wall outer wall having reinforcement to assist handling (not for structural stability) 3.4 structural reinforcement additional strengthening for structural stability (in the outer wall) 3.5 freeze-thaw-resistance ability of the product to resist the effects of freezing and thawing 3.6 opening section flue liner which has an opening for cleaning and inspection or connection for another flue (junction) 3.7 cleaning and inspection door door in outer wall element to allow cleaning and inspection of the chimney. There are two types of cleaning and inspection doors (see Figure 2): - a cleaning and inspection door combined with an opening section with inner door - a cleaning and inspection door combined with an opening section without inner door

Key 1 Cleaning and inspection door 2 Inner door of the opening section 3 Opening section 4 Insulation layer 5 Outer wall Figure 2 - Examples of cleaning and inspection doors and the opening sections 3.8 distance piece spacer to keep distance between outer wall element and insulation or inner liner 4 Shapes, dimensions and tolerances 4.1 Flue liners 4.1.1 General Flue liners shall meet the requirements on size and tolerance of dimensions given in 7.1, 7.2, 7.3, 7.4, 7.5, 7.6 and 7.7 of EN 1457:1999. 4.1.2 External dimensions of flue liner When tested in accordance with A.2.6, the external dimensions of flue liners measured on any cross section shall not deviate more than ± 3 % of the manufacturer’s stated nominal external dimensions. 4.2 Insulation The insulation layer shall meet the requirements on tolerance of dimensions given in 4.2.2 (length and width) and 4.2.3 (thickness class T3) of EN 13162:2001.

EN 12446:2003, Clause 7 clay/ceramic outer walls:
EN 13069:2005, Clause 6 metal oute
...


SLOVENSKI STANDARD
01-maj-2006
'LPQLNL6LVWHPVNLGLPQLNLVNHUDPLþQLPLWXOMDYDPLGHO=DKWHYH]DRGSRUQRVW
SURWLSRåDUXVDMLQSUHVNXVQHPHWRGH
Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and
test methods for sootfire resistance
Abgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 1: Anforderungen
und Prüfungen für Rußbrandbeständigkeit
Conduits de fumées - Conduits-systémes avec conduit intérieur en terre cuite/céramique
- Partie 1: Exigences et méthodes d'essai relatives a la détermination de la résistance au
feu de cheminée
Ta slovenski standard je istoveten z: EN 13063-1:2005
ICS:
91.060.40 Dimniki, jaški, kanali Chimneys, shafts, ducts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13063-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 91.060.40
English Version
Chimneys - System chimneys with clay/ceramic flue liners - Part
1: Requirements and test methods for sootfire resistance
Conduits de fumées - Conduits-systémes avec conduit Abgasanlagen - System-Abgasanlagen mit Keramik-
intérieur en terre cuite/céramique résistant au feu de Innenrohren - Teil 1: Anforderungen und Prüfungen für
cheminée - Partie 1: Exigences et méthodes d'essai Rußbrandbeständigkeit
This European Standard was approved by CEN on 2 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13063-1:2005: E
worldwide for CEN national Members.

Contents
page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions.5
4 Shapes, dimensions and tolerances .7
4.1 Flue liners.7
4.2 Insulation.7
4.3 Outer wall elements .8
4.4 Cleaning and inspection doors.8
5 Material requirements.8
5.1 General requirements for components .8
5.2 Safety in use.10
5.3 Hygiene, health and environment.11
5.4 Cleaning and inspection doors.11
5.5 Freeze/thaw resistance.12
5.6 Temperature classes .12
5.7 Pressure classes.12
6 Replacement of single components of the system chimney.12
6.1 Change of flue liner.12
6.2 Change of opening sections .12
6.3 Change of insulation.13
6.4 Change of jointing materials for inner liners .13

6.5 Change of outer wall elements .13
6.6 Change of cleaning and inspection doors .13
7 Designation .13
8 Product information.14
9 Marking and labelling .15
10 Evaluation of conformity .15
10.1 General .15
10.2 Components .15
10.3 Initial type testing of soot fire resistant system chimneys.16
10.4 Exchange of components.16
10.5 Factory production control .17
Annex A (normative)  Test methods.18
Annex B (normative)  Stainless steel outer walls.24
Annex C (normative)  Thermal resistance of the system chimney .25
Annex D (normative)  Sampling procedures for an AQL of 10 % and inspection level S2.26
Annex ZA (informative)  Clauses of this European Standard addressing the provisions of the EU
Construction Product Directive .30
Bibliography.37

Foreword
This European Standard (EN 13063-1:2005) has been prepared by Technical Committee CEN/TC 166
“Chimneys”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at
the latest by September 2007.
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA which is an integral part of this document.
This standard is part 1 of a series of standards for system chimneys with clay/ceramic flue liners.
Part 2 is for system chimneys working under wet conditions and part 3 is for system air flue chimneys.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
1 Scope
This European Standard specifies the requirements and test methods for multiwall soot fire resistant system
chimneys, working under dry conditions, with corrosion resistance 3, with negative pressure (see EN 1443) in
which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking
and inspection are also covered by this standard.
This standard does not apply to structurally independent (free standing or self-supporting) system chimneys.
A soot fire resistant system chimney has the following items where appropriate:
 clay/ceramic flue liners;
 Insulation layer;
 outer walls;
 mortar for jointing flue liners;
 mortar for jointing outer walls;
 terminal;
 chimney base;
 cladding;
 opening section;
 cleaning and inspection door;
 distance piece;
 reinforcement.
The soot fire resistant chimney covers a combination of compatible chimney components, obtained or
specified from one manufacturing source with product responsibility for the whole chimney.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 998-2:2003, Specification for mortar for masonry – Part 2: Masonry mortar.
EN 1366-8, Fire resistance tests for service installations – Part 8: Smoke extraction ducts.
EN 1443:2003, Chimneys – General requirements.
EN 1457:1999, Chimneys – Clay/ceramic flue liners – Requirements and test methods.
EN 1806:2000, Chimneys – Clay/ceramic flue blocks for single wall chimneys –Requirements and test
methods.
EN 1859, Chimneys – Metal chimneys – Test methods.
EN 12446:2003, Chimneys – Components – Concrete outer wall elements.
EN 13069:2005, Chimneys – Clay/ceramic outer walls for system chimneys – Requirements and test methods.
EN 13162:2001, Thermal insulation products for buildings – Factory made mineral wool (MW) products –
Specification.
EN 13216-1:2004, Chimneys –Test methods for system chimneys – Part 1: General test methods.
EN 13384-1, Chimneys - Thermal and fluid dynamic calculation methods – Part 1: Chimneys serving one
appliance.
EN 14297:2004, Chimneys – Freeze-thaw resistance test method for chimney products.
EN ISO 1182, Reaction to fire tests for building products – Non-combustibility test (ISO 1182:2002).
ISO 2859-1, Sampling procedures for inspection by attributes – Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection.

3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 1443:2003 and
EN 13216-1:2004 and the following apply.
3.1
soot fire resistant multiwall system chimney
multiwall construction, consisting mainly of an outer wall, an insulation layer and a sootfire resistant inner
clay/ceramic flue liner. The combination of these components forms a sootfire resistant system chimney (see
Figure 1)
Key
1 Inner liner
2 Insulation layer
3 Outer wall
4 Cavities for back ventilation
5 Cavities for structural reinforcement
Figure 1 – Construction of a soot fire resistant system chimney
3.2
chimney base
section of the system chimney, situated at the bottom, which comprises an inspection opening with door
3.3
reinforced outer wall
outer wall having reinforcement to assist handling (not for structural stability)
3.4
structural reinforcement
additional strengthening for structural stability (in the outer wall)
3.5
freeze-thaw-resistance
ability of the product to resist the effects of freezing and thawing
3.6
opening section
flue liner which has an opening for cleaning and inspection or connection for another flue (junction)
3.7
cleaning and inspection door
door in outer wall element to allow cleaning and inspection of the chimney. There are two types of cleaning
and inspection doors (see Figure 2):
- a cleaning and inspection door combined with an opening section with inner door
- a cleaning and inspection door combined with an opening section without inner door
Key
1 Cleaning and inspection door
2 Inner door of the opening section
3 Opening section
4 Insulation layer
5 Outer wall
Figure 2 - Examples of cleaning and inspection doors and the opening se
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15287-2:2023(Main)
Chimneys - Design, installation and commissioning - Part 2: Chimneys and connecting flue pipes for room sealed combustion appliances
SIST EN 15287-2:2023

This document describes the method of specifying the design, installation and labelling criteria for chimney systems, construction of custom-built chimneys, the relining or converting of existing chimneys, connecting flue pipes and air supply pipes for room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
This document does not cover:
-   chimneys which serve a mixture of fan assisted or forced draught burners or natural draught appliances,
-   installations having a configuration of the type C2.
NOTE   Room sealed gas appliances are classified as type C according to EN 1749.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances. The methods in Part 1 of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances.

  • Standard
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15287-1:2023(Main)
Chimneys - Design, installation and commissioning - Part 1: Chimneys and connecting flue pipes for non-room sealed combustion appliances
SIST EN 15287-1:2023

This document describes the method of specifying the design, installation and labelling criteria for system chimneys, construction of custom-built chimneys, the relining of existing chimneys and connecting flue pipes for non-room sealed combustion appliances as well as the use of chimney products. It also gives information on commissioning of an installed chimney.
This document applies to chimneys which are subject to the following limiting conditions:
-   the distance between the supports not to exceed 4 m;
-   the distance above the last structural attachment not to exceed 3 m;
-   the free-standing height above the uppermost structural support attachment for chimneys with rectangular cross section is not more than five times the smallest external dimension.
The methods in this part of this document are applicable to chimneys and connecting flue pipes for non-room sealed combustion appliances. The methods in Part 2 of this document are applicable to chimneys and connecting flue pipes for room sealed combustion appliances.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-7:2016+A1:2020(Main + Amendment)
Chimneys - Accessories - Part 7: Rain caps - Requirements and test methods
SIST EN 16475-7:2016+A1:2020

This European Standard specifies requirements and test methods for rain caps that are used as components, subject to flue gas, in order to prevent rain entry into the chimneys. Rain caps already tested together with system chimney products or other chimney components, e.g. terminals, are not covered by this standard. Rain caps incorporating a bird guard are also included. It also specifies the requirements for marking, manufacturers’ instruction, product information and evaluation of conformity.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-4:2020(Main)
Chimneys - Accessories - Part 4: Flue dampers - Requirements and test methods
SIST EN 16475-4:2020

This document specifies the characteristics and test methods for flue dampers that are used as components, carrying flue gas, in order to limit the flow in a chimney or to prevent back flow of soot during cleaning of the chimney or to prevent the backflow of the flue gas e.g. in case of multi-served chimneys.
This document covers only flue dampers incorporated in a housing and installed inside a building.
This document covers only flue dampers with sealings made of elastomeric materials for temperature classes up to T 200 and corrosion class 1 or 2 in accordance with EN 14241-1 or sealing materials for dry applications with a fire reaction class A1 in accordance with EN 13501-1.
This document covers only flue dampers with motor drive, casing and flue damper plate which are interlocked in such a way that they can only be separated by using tools.
This document covers only mechanical flue dampers where any motor is in accordance with EN 60730-2-14 and the cover for electrical components of the flue damper fulfils minimum protection class IP40 according to EN 60529.
This document covers only flue dampers which are designed and installed to ensure that incorrect information about the position of the flue damper flap are absolutely impossible, which are only installed on components that are interlocked to the casing, which are only activated by components that are interlocked to the flue damper flap and where it is ensured that the limit switch opens or the flue damper flap moves to the open position if one of these interlocks fails. This safety target may also be achieved with an equally suitable method (e.g. bracing or welding).
This document covers only flue dampers for biomass boilers ≥ 1 000 kW and industrial applications with limit switches in accordance with EN 61058-1 or EN 50156-1.
This document covers only flue dampers where it is possible to identify the position of the flue damper flap.
This document covers only totally closed, manually driven flue dampers (type 1) which have a facility to adjust the position of the flue damper flap.
This document covers only totally closed, mechanically driven flue dampers (type 2) with only the positions "fully opened" and "fully closed" and where it is not possible to fix the flap in the non-closed position during the flue damper flap stays in closed position while the appliance is not working.
NOTE   This applies only to multi-appliance installations with positive pressure conditions.
This document covers only partially closed flue dampers (type 3 to 5) where it is possible to adjust the position of the flue damper flap and where it is ensured that the flue damper flap does not change position by itself.
Flue dampers which are integral parts of system chimney products or other chimney components, e.g. flue liners, connecting flue pipes, are not covered by this document.
This document also specifies the provisions for marking, manufacturers’ instruction, product information, Assessment and Verification of Constancy of Performance (AVCP).
This document does not specify issues for electrical parts.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-1:2020(Main)
Chimneys - Accessories - Part 1: Chimney silencers - Requirements and test methods
SIST EN 16475-1:2020

This European Standard specifies requirements and test methods for flue gas silencers made of metal that are used as accessories in order to reduce the noise level of combustions appliances.
The standard covers silencers in the connecting flue pipes and on top of chimneys.
This standard does not cover silencers installed as chimney sections. This standard excludes active silencers.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16475-6:2020(Main)
Chimneys - Accessories - Part 6: Access components - Requirements and test methods
SIST EN 16475-6:2020

This document specifies the requirements and test methods for access components comprising a frame and a door or doors which provide access to the flue of a chimney for the purpose of inspection or cleaning.
Access components for higher nominal working temperature than 450 °C, positive pressure and wet applications are not covered by this standard.
The document is limited to access components with door opening dimensions with a maximum width of 450 mm and a maximum height of 600 mm.
Products not freely ventilated are excluded from this document.
This document also specifies the requirements for marking, manufacturers’ instruction, product information and information on the AVCP (Assessment and Verification of Constancy of Performance).
Access components already tested together with system chimney products or other chimney components, e.g. flue liners, are not covered by this document.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13384-1:2015+A1:2019(Main + Amendment)
Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one combustion appliance
SIST EN 13384-1:2015+A1:2019

This European Standard specifies methods for the calculation of the thermal and fluid dynamic characteristics of chimneys serving one heating appliance.
The methods in this part of this European Standard are applicable to negative or positive pressure chimneys with wet or dry operating conditions. It is valid for chimneys with heating appliances for fuels subject to the knowledge of the flue gas characteristics which are needed for the calculation.
The methods in this part of this European Standard are applicable to chimneys with one inlet connected with one appliance. The methods in Part 2 of this European Standard are applicable to chimneys with multiple inlets and one inlet with multiple appliances. Part 3 describes methods for the development of diagrams and tables for chimneys serving one heating appliance.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13384-2:2015+A1:2019(Main + Amendment)
Chimneys - Thermal and fluid dynamic calculation methods - Part 2: Chimneys serving more than one combustion appliance
SIST EN 13384-2:2015+A1:2019

This part of EN 13384 specifies methods for calculation of the thermal and fluid dynamic characteristics of chimneys serving more than one heating appliance.
This part of EN 13384 covers both the cases, either
a)   where the chimney is connected with more than one connecting flue pipe from individual or several appliances in a multi-inlet arrangement; or
b)   where the chimney is connected with an individual connecting flue pipe connecting more than one appliance in a cascade arrangement.
The case of multiple inlet cascade arrangement is covered by the case a).
This part of EN 13384 deals with chimneys operating under negative pressure conditions (there can be positive pressure condition in the connecting flue pipe) and with chimneys operating under positive pressure conditions and is valid for chimneys serving heating appliances for liquid, gaseous and solid fuels.
This part of EN 13384 does not apply to:
-   chimneys with different thermal resistance or different cross-section in the various chimney segments. This part does not apply to calculate energy gain;
-   chimneys with open fire places, e.g. open fire chimneys or chimney inlets which are normally intended to operate open to the room;
-   chimneys which serve different kinds of heating appliances regarding natural draught, fan assisted, forced draught or combustion engine. Fan assisted appliances with draught diverter between the fan and the chimney are considered as natural draught appliances;
-   chimneys with multiple inlets from more than 5 storeys. (This does not apply to balanced flue chimney.);
-   chimneys serving heating appliances with open air supply through ventilation openings or air ducts, which are not installed in the same air supply pressure region (e.g. same side of building).
For positive pressure chimneys this part only applies if any heating appliance which is out of action can be positively isolated to prevent flue gas back flow.

  • Standard
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1443:2019(Main)
Chimneys - General requirements
SIST EN 1443:2019

This document specifies requirements and the basic performance criteria for chimneys, flue liners, connecting flue pipes, components and accessories used to convey the products of combustion from combustion appliances to the outside atmosphere. This document is to be used as a reference for all product standards of CEN/TC 166.
This document specifies sootfire resistant chimneys, flue liners, connecting flue pipes, fittings and accessories for combustion appliances burning solid, liquid and gaseous fuels and non-sootfire resistant chimneys, flue liners, connecting flue pipes, components and accessories for combustion appliances burning liquid and gaseous fuels only. It also specifies sootfire safe accessories for combustion appliances burning solid, liquid and gaseous fuels.
NOTE 1   This means that chimneys, flue liners, connecting flue pipes and components which are non-sootfire resistant and accessories which are non-sootfire resistant or non-sootfire safe are not suitable for combustion appliances burning solid fuel.
This document also identifies minimum requirements for marking, instructions, product information and provides guidance for the assessment and verification of constancy of performance (AVCP).
This document does not apply to structurally independent chimneys and custom-built chimneys consisting of non-CE-marked components.
NOTE 2   This document can be used as a basis for the specifications of products covered by a European Technical Assessment.
NOTE 3   All product standards drafted by Technical Committee CEN/TC 166 are based on the Mandate M/105.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    42 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13216-1:2019(Main)
Chimneys - Test methods for system chimneys - Part 1: General test methods
SIST EN 13216-1:2019

This document specifies material-independent general test methods for all system chimneys. It can be used for all flue gas carrying products.
NOTE   The thermal performance tests for the determination of the distance to combustible material for accessories (draught regulators, access components, etc.) are included in different standards of CEN/TC 166.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day