EN ISO 22391-3:2009/A2:2021

SLOVENSKI STANDARD
SIST EN ISO 22391-3:2010/A2:2021
01-december-2021
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polietilen s povišano temperaturno odpornostjo (PE-RT) - 3. del: Fitingi - Dopolnilo
A2 (ISO 22391-3:2009/Amd 2:2021)
Plastics piping systems for hot and cold water installations - Polyethylene of raised
temperature resistance (PE-RT) - Part 3: Fittings - Amendment 2 (ISO 22391-
3:2009/Amd 2:2021)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polyethylen
erhöhter Temperaturbeständigkeit (PE-RT) - Teil 3: Formstücke - Änderung 2 (ISO
22391-3:2009/Amd 2:2021)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polyéthylène de meilleure résistance à la température (PE-RT) - Partie 3: Raccords -
Amendement 2 (ISO 22391-3:2009/Amd 2:2021)
Ta slovenski standard je istoveten z: EN ISO 22391-3:2009/A2:2021
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 22391-3:2010/A2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 22391-3:2010/A2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 22391-3:2010/A2:2021


EN ISO 22391-3:2009/A2
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 23.040.45; 91.140.60; 93.025
English Version

Plastics piping systems for hot and cold water installations
- Polyethylene of raised temperature resistance (PE-RT) -
Part 3: Fittings - Amendment 2 (ISO 22391-3:2009/Amd
2:2021)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polyéthylène de Kaltwasserinstallation - Polyethylen erhöhter
meilleure résistance à la température (PE-RT) - Partie Temperaturbeständigkeit (PE-RT) - Teil 3: Formstücke
3: Raccords - Amendement 2 (ISO 22391-3:2009/Amd - Änderung 2 (ISO 22391-3:2009/Amd 2:2021)
2:2021)
This amendment A2 modifies the European Standard 2777447; it was approved by CEN on 1 October 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22391-3:2009/A2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 22391-3:2010/A2:2021
EN ISO 22391-3:2009/A2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 22391-3:2010/A2:2021
EN ISO 22391-3:2009/A2:2021 (E)
European foreword
This document (EN ISO 22391-3:2009/A2:2021) has been prepared by Technical Committee ISO/TC
138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held
by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete li
...