prEN ISO 15029-2
(Main)Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 2: Spray test - Stabilized flame heat release spray method (ISO/DIS 15029-2:2006)
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 2: Spray test - Stabilized flame heat release spray method (ISO/DIS 15029-2:2006)
2010-10-15 EMA: No new information about this project, still cancelled in ISO. WI deleted.
2009-10-27 EMA: WI deleted at ISO, waiting for TC secretary 's reply (see e-mail in WI folder, under Current).
Migrated from Progress Sheet (TC Comment) (2000-07-10): WIs 174 and 189 are the result of the splitting of WI 174 ++ new Tc forecast in BP Bli (991022) ++ New TC forecasts in rev BP (NT/01-01-02)
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Zündeigenschaften von Sprühstrahlen schwer entflammbarer Flüssigkeiten - Teil 2: Sprühstrahl-Zündprüfung - Wärmeabgabe einer stabilisierten Flamme (ISO/DIS 15029-2:2006)
Dieser Teil von ISO 15029 legt eine Sprühstrahl-Zündprüfung fest, mit der die Brandgefahr von unter Druck versprühten schwer entflammbaren Flüssigkeiten verglichen werden kann. In einer luftdurchströmten Kammer wird ein aus Flüssigkeit und Druckluft bestehender Sprühstrahl zwei Formaten einer definierten Flamme eines Gasbrenners ausgesetzt. Beim Betrieb des Brenners ohne und mit aus der Düse austretender Flüssigkeit werden die Wärmeabgabe, die Flammenlänge und die Rauchdichte ermittelt und somit quantitative Informationen über das Brandverhalten der Flüssigkeit erhalten. Ein Schema zur Klassifizierung der Flüssigkeiten wird angegeben. Mindestanforderungen werden jedoch nicht genannt.
Produits pétroliers et produits connexes - Détermination des caractéristiques d'inflammation des fluides difficilement inflammables en jet pulvérisé - Partie 2: Essai sur jet pulvérisé - Méthode par dégagement de chaleur d'une flamme stabilisée (ISO/DIS 15029-2:2006)
Nafta in sorodni proizvodi - Določanje vžignih lastnosti tekočin, odpornih proti ognju, ob razpršitvi - 2. del: Pršni preskus – Pršna sprostilna metoda s stabiliziranim plamenskim segrevanjem (ISO/DIS 15029-2:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 15029-2:2007
01-februar-2007
1DIWDLQVRURGQLSURL]YRGL'RORþDQMHYåLJQLKODVWQRVWLWHNRþLQRGSRUQLKSURWL
RJQMXREUD]SUãLWYLGHO3UãQLSUHVNXV±3UãQDVSURVWLOQDPHWRGDV
VWDELOL]LUDQLPSODPHQVNLPVHJUHYDQMHP,62',6
Petroleum and related products - Determination of spray ignition characteristics of fire-
resistant fluids - Part 2: Spray test - Stabilized flame heat release spray method (ISO/DIS
15029-2:2006)
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Zündeigenschaften von
Sprühstrahlen schwer entflammbarer Flüssigkeiten - Teil 2: Sprühstrahl-Zündprüfung -
Wärmeabgabe einer stabilisierten Flamme (ISO/DIS 15029-2:2006)
Produits pétroliers et produits connexes - Détermination des caractéristiques
d'inflammation des fluides difficilement inflammables en jet pulvérisé - Partie 2: Essai sur
jet pulvérisé - Méthode par dégagement de chaleur d'une flamme stabilisée (ISO/DIS
15029-2:2006)
Ta slovenski standard je istoveten z: prEN ISO 15029-2
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
75.080 Naftni proizvodi na splošno Petroleum products in
general
oSIST prEN ISO 15029-2:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15029-2:2007
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15029-2:2007
EUROPEAN STANDARD
DRAFT
prEN ISO 15029-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2006
ICS 13.220.40; 75.080
English Version
Petroleum and related products - Determination of spray ignition
characteristics of fire-resistant fluids - Part 2: Spray test -
Stabilized flame heat release spray method (ISO/DIS 15029-
2:2006)
Produits pétroliers et produits connexes - Détermination
des caractéristiques d'inflammation des fluides difficilement
inflammables en jet pulvérisé - Partie 2: Essai sur jet
pulvérisé - Méthode par dégagement de chaleur d'une
flamme stabilisée (ISO/DIS 15029-2:2006)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 19.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 15029-2:2006: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15029-2:2007
prEN ISO 15029-2:2006 (E)
Foreword
This document (prEN ISO 15029-2:2006) has been prepared by Technical Committee ISO/TC
28 "Petroleum products and lubricants" in collaboration with Technical Committee CEN/TC 19
"Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and
biological origin", the secretariat of which is held by NEN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO/DIS 15029-2:2006 has been approved by CEN as prEN ISO 15029-2:2006
without any modifications.
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15029-2:2007
DRAFT INTERNATIONAL STANDARD ISO/DIS 15029-2
ISO/TC 28 Secretariat: ANSI
Voting begins on: Voting terminates on:
2006-11-09 2007-04-09
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Petroleum and related products — Determination of spray
ignition characteristics of fire-resistant fluids —
Part 2:
Spray test — Stabilized flame heat release spray method
Produits pétroliers et produits connexes — Détermination des caractéristiques d'inflammation des fluides
difficilement inflammables en jet pulvérisé —
Partie 2: Essai sur jet pulvérisé — Méthode par dégagement de chaleur d'une flamme stabilisée
ICS 13.220.40; 75.080
ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2006
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2006 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
Contents Page
Foreword.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle.2
5 Reagents and materials .2
6 Apparatus .2
6.1 Test installation .2
6.1.1 General.2
6.1.2 Combustion chamber.3
6.1.3 Extraction system.3
6.1.4 Spray delivery system (see Figure 3) .3
6.1.5 Burner system (see Figure 4) .5
6.1.6 Burner and atomizer mounting .6
6.2 Instrumentation.6
6.2.1 Temperature sensors .6
6.2.2 Anemometer.6
6.2.3 Flame length scale.6
6.2.4 Smoke meter .6
6.2.5 Calibration of instruments.8
7 Sampling and sample preparation.8
8 Apparatus preparation .8
9 Procedure .9
3
9.1 Measurements at a propane flow rate of 0,13 Nm /h .9
3
9.2 Measurements at a propane flow rate of 0,4 Nm /h .9
9.3 Abandonment of tests.10
9.4 Tabulation of measurements.10
9.5 Number of tests .10
9.5.1 General.10
9.5.2 Calculation .10
9.5.3 Marginal values.11
9.5.4 Conclusion .11
10 Calculations .11
10.1 Ignitability factor.11
3
10.1.1 At propane flow rate of 0,13 Nm /h .11
3
10.1.2 At propane flow rate of 0,4 Nm /h .11
10.2 Flame length index .12
3
10.2.1 At propane flow rate of 0,13 Nm /h .12
3
10.2.2 At propane flow rate of 0,4 Nm /h .12
11 Expression of results .12
11.1 Individual results .12
11.2 Ranking system .12
12 Precision.13
13 Test report.13
Annex A (normative) Verification of propane pressure and flow rate.14
© ISO 2006 — All rights reserved iii
---------------------- Page: 7 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
A.1 Apparatus.14
A.1.1 Pressure gauge.14
A.1.2 Flowmeter.14
A.2 Procedure.14
A.2.1 Measurement.14
A.2.2 Verification .14
Annex B (normative) Verification of propane flame characteristics.15
B.1 Apparatus.15
B.1.1 General.15
B.1.2 Temperature sensor .15
B.1.3 Traverse system.15
B.1.4 Insulation board.16
B.2 Flame temperature measurements .16
B.2.1 Axial temperatures.16
B.2.2 Radial temperatures .16
B.3 Verification .16
B.3.1 Standard values .16
B.3.2 Conformity values.16
Annex C (normative) Test apparatus calibration.19
C.1 Calibration fluids.19
C.2 Testing.19
C.3 Calibration .19
Annex D (informative) Example proformas for test results .21
D.1 General.21
iv © ISO 2006 — All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15029-2 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants.
ISO 15029 consists of the following parts, under the general title Petroleum and related products — Determination
of spray ignition characteristics of fire-resistant fluids:
⎯ Part 1: Spray flame persistence — Hollow-cone nozzle method
⎯ Part 2: Spray test — Stabilized flame heat release method
⎯ Part 3: Spray test — Large scale method
© ISO 2006 — All rights reserved v
---------------------- Page: 9 ----------------------
oSIST prEN ISO 15029-2:2007
---------------------- Page: 10 ----------------------
oSIST prEN ISO 15029-2:2007
DRAFT INTERNATIONAL STANDARD ISO/DIS 15029-2
Petroleum and related products — Determination of spray ignition
characteristics of fire-resistant fluids — Part 2: Spray test -
Stabilized flame heat release method
WARNING — The use of this part of ISO 15029 may involve hazardous materials, operations and equipment.
This part of ISO 15029 does not purport to address all of the safety problems associated with its use. It is
the responsibility of the user of this part of ISO 15029 to establish appropriate safety and health practices
and determine the applicability of regulatory limitations prior to use.
1 Scope
This part of ISO 15029 specifies a method by which the fire hazards of pressurized sprays of liquid fire-resistant
fluids can be compared. Two sizes of propane flame are used to ignite and stabilize combustion of an air-atomized
release of fluid, and measurements related to the rate of heat release, length of flame and density of smoke are
taken to give quantitative information on the fire behaviour of the fluid. A scheme for classification of the fluids is
given, but no minimum performance requirements are specified.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
ISO 3170:2004, Petroleum liquids — Manual sampling
ISO 3696:1987, Water for analytical laboratory use — Specification and test methods
ISO 5659-2:1994, Plastics — Smoke generation — Part 2: Determination of optical density by a single-chamber
test
ISO 9162:1989, Petroleum products — Fuels (class F) — Liquefied petroleum gases — Specifications
IEC 60584-1:1995, Thermocouples — Part 1: Reference tables
3 Terms and definitions
For the purposes of this part of ISO 15029, the following terms and definitions apply.
3.1
stabilized flame
point at which the rate of energy release, flame length and other combustion properties, are steady as a function of
time, so that sensible time-averaged values can be calculated
3.2
flame length
distance in millimetres from the vertical centre line of the gas burner to the furthest downstream point reached by
the visible flame
© ISO 2006 — All rights reserved 1
---------------------- Page: 11 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
3.3
flame length index
function of the flame length and propane flow rate
3.4
ignitability factor
corrected value, to the nearest integer, of a function of heat release at a specific propane flow rate
3.5
smoke density
smoke density as defined in ISO 5659, as a function of smoke opacity in the flue pipe before and after introduction
of the test fluid
4 Principle
A pre-conditioned flux of the test fluid is delivered to a test chamber through a twin-fluid atomizer. Compressed air,
supplied to the nozzle at a controlled rate, is used to produce an atomized spray, which is exposed to a defined
flame of a gas burner present throughout the test. The gas flame acts to produce, by input of heat at a steady rate,
a stabilized spray flame (3.1), so that combustion properties, such as the rate of energy release and flame length,
are sufficiently steady over time to allow time-averaged values to be measured.
Temperatures are measured both at the entry to the combustion chamber and in the exhaust, with the burner
operating first without, and then with, release of the test fluid. The flame length (3.2) and smoke opacity of the
exhaust are also measured. Calculations of functions, such as flame length index (3.3), ignitability factor (3.4) and
smoke density (3.5) are made from these measurements. Sampling of the exhaust can enable the production rate
of other combustion products to be determined. A grading system for the performance of fire-resistant fluids is
developed from these determinations and calculations.
5 Reagents and materials
5.1 Propane, high purity (minimum 98 %) grade, generally conforming to the requirements of ISO 9162.
5.2 Nitrogen, oxygen-free, commercial grade.
5.3 Compressed air.
5.4 Water, conforming to the requirements of grade 3 of ISO 3696.
5.5 Ethylene glycol, laboratory grade (mono, 98 % purity).
6 Apparatus
6.1 Test installation
6.1.1 General
Figure 1 gives a general layout of the test installation. The major components of the installation are described in
6.1.2 to 6.1.6.
2 © ISO 2006 — All rights reserved
---------------------- Page: 12 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
Figure 1 — General view of installation
6.1.2 Combustion chamber
This shall be fabricated from steel sheet, 8 mm thick, of square cross-section with internal dimensions of
(2 000 ± 5) mm x (490 ± 5) mm. The inner and outer surfaces shall be painted with black heat-resistant paint. A
clear window of heat-resistant glass, 8,5 mm thick, shall be located in one side of the chamber. The glass shall be
(1 920 ± 10) mm x (525 ± 10) mm providing an open area of the window of (1 880 ± 10) mm x (480 ± 10) mm. The
window may be hinged to allow access to the chamber. All joints around the window shall be sealed during use.
The combustion chamber is illustrated in Figure 2.
6.1.3 Extraction system
The combustion chamber exit shall be connected to a contraction fabricated from steel sheet 1 mm thick, providing
a transition from the square to a circular cross-section with an internal diameter of 250 mm ± 4 mm. This
contraction is connected to a horizontal section of flue pipe 1 400 mm ± 10 mm in length, which in turn may be
connected to further exhaust ducting or clearing system that shall be designed to provide stable conditions in the
combustion chamber during a test.
The air flow through the chamber is produced by a jet pump mounted in the exhaust duct, producing an air velocity
of 1,4 m/s ± 0,1 m/s measured 50 mm ± 2 mm inside the combustion chamber inlet. The temperature of the air
entering the chamber shall be sufficiently constant within the range 10 °C to 25 °C, such that the temperature
variation over a period of 30 s shall not exceed 1 °C. The relative humidity of the air shall lie between 40 % and
80 %. The combustion chamber and exhaust system are illustrated in Figure 2.
6.1.4 Spray delivery system (see Figure 3)
6.1.4.1 Test fluid. The fluid shall be contained in a steel reservoir of minimum capacity 3 l, designed for an
internal pressure of 2,5 MPa at 20 °C. The flow of fluid from the reservoir is controlled by means of pressurized
nitrogen (5.2) supplied to the upper part of the reservoir, with a valve situated in the nitrogen supply pipe. Means
shall be provided to permit complete drainage of the system. The test fluid volume flow rate shall be controlled to
90 ml/min ± 0,5 ml/min at a temperature between 10 °C and 25 °C, by means of a valve, and measured
© ISO 2006 — All rights reserved 3
---------------------- Page: 13 ----------------------
oSIST prEN ISO 15029-2:2007
ISO/DIS 15029-2
1)
continuously during the test by means of a volumetric flowmeter. The fluid is delivered to the atomizer through
nylon and/or steel piping with an internal diameter of 7,5 mm ± 2,5 mm, rated at 2 MPa, and the flowmeter shall be
located 350 mm ± 150 mm downstream of the valve.
6.1.4.2 Compressed air. Compressed air shall be supplied, via a filter to remove droplets and particulates, at
3 3
a steady flow rate of 1,92 Nm /h ± 0,05 Nm /h at a pressure of at least 0,2 MPa. The flow rate shall be measured
3 3
by a variable area flowmeter having a flow range of 0,4 Nm /h to 3,0 Nm /h, located 3 500 mm ± 500 mm before
the spray jet, and controlled by a valve installed downstream of the flowmeter. The temperature of the atomizing air
shall be between 10 °C and 25
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.