EN 2638:2019
(Main)Aerospace series - Aluminium alloy 2024- - T3 - Extruded bar and section - 1,2 mm ≤ (a or D) ≤ 150 mm with coarse peripheral grain control
Aerospace series - Aluminium alloy 2024- - T3 - Extruded bar and section - 1,2 mm ≤ (a or D) ≤ 150 mm with coarse peripheral grain control
This document specifies the requirements relating to:
Aluminium alloy 2024 - -
T3
Extruded bar and section
1,2 mm ≤ (a or D) ≤ 150 mm
with coarse peripheral grain control
for aerospace applications.
Luft- und Raumfahrt - Aluminiumlegierung 2024‑ - T3 - Stranggepresste Stangen und Profile - 1,2 mm ≤ (a oder D) ≤ 150 mm mit Kontrolle der Grobkornrandzone
Dieses Dokument legt die Anforderungen an:
Aluminiumlegierung 2024-T3
Stranggepresste Stangen und Profile
1,2 mm ≤ (a oder D) ≤ 150 mm
mit Kontrolle der Grobkornrandzone
für Anwendungen in der Luft- und Raumfahrt fest.
Série aérospatiale - Alliage d'aluminium 2024- - T3 - Barres et profilés filés - 1,2 mm ≤ (a ou D) ≤ 150 mm avec contrôle de la zone périphérique à gros grains
Le présent document spécifie les exigences liées à :
Alliage en aluminium 2024-T3 Barre et profilés filés
1,2 mm ≤ (a ou D) ≤ 150 mm avec contrôle de la zone périphérique à gros grains
pour les applications aérospatiales.
Aeronavtika - Aluminijeva zlitina 2024 - T3 - Ekstrudirane palice in profili - 1,2 mm ≤ (a ali D) ≤ 150 mm z nadzorom hrapavosti zunanjih zrn
Ta dokument določa zahteve, ki se nanašajo na:
aluminijevo zlitino 2024 - -
T3
ekstrudirane palice in profili
1,2 mm ≤ (a ali D) ≤ 150 mm
z nadzorom hrapavosti zunanjih zrn
za uporabo v aeronavtiki.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2019
Aeronavtika - Aluminijeva zlitina 2024 - T3 - Ekstrudirane palice in profili - 1,2 mm ≤
(a ali D) ≤ 150 mm z nadzorom hrapavosti zunanjih zrn
Aerospace series - Aluminium alloy 2024-T3 - Extruded bar and section - 1,2 mm ≤ (a or
D) ≤ 150 mm with coarse peripheral grain control
Luft- und Raumfahrt - Aluminiumlegierung 2024-T3 - Stranggepresste Stangen und
Profile 1,2 mm ≤ (a or D) ≤ 150 mm mit Kontrolle der Grobkornrandzone
Série aérospatiale - Alliage d'aluminium 2024-T3 - Barres et profilés filés - 1,2 mm ≤ (a
or D) ≤ 150 mm avec contrôle de la zone périphérique à gros grains
Ta slovenski standard je istoveten z: EN 2638:2019
ICS:
49.025.20 Aluminij Aluminium
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 2638
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2019
EUROPÄISCHE NORM
ICS 49.025.20
English Version
Aerospace series - Aluminium alloy 2024- - T3 - Extruded
bar and section - 1,2 mm ≤ (a or D) ≤ 150 mm with coarse
peripheral grain control
Série aérospatiale - Alliage d'aluminium 2024- - T3 - Luft- und Raumfahrt - Aluminiumlegierung 2024- - T3 -
Barres et profilés filés - 1,2 mm ≤ (a or D) ≤ 150 mm Stranggepresste Stangen und Profile - 1,2 mm ≤ (a or
avec contrôle de la zone périphérique à gros grains D) ≤ 150 mm mit Kontrolle der Grobkornrandzone
This European Standard was approved by CEN on 20 August 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2638:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 6
European foreword
This document (EN 2638:2019) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2019, and conflicting national standards
shall be withdrawn at the latest by November 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.