EN ISO 10833:2019

SLOVENSKI STANDARD
01-september-2019
Nadomešča:
SIST EN 1814:2006
Tekstilne talne obloge - Ugotavljanje odpornosti rezanih robov proti poškodbam z
modificiranim bobnastim preskusom po Vettermannu (ISO 10833:2017)
Textile floor coverings - Determination of resistance to damage at cut edges using the
modified Vettermann drum test (ISO 10833:2017)
Textile Bodenbeläge - Bestimmung der Schnittkantenfestigkeit mit der modifizierten
Vettermann-Trommelprüfung (ISO 10833:2017)
Revêtements de sol textiles - Détermination de la résistance des joints par l'essai au
tambour Vettermann modifié (ISO 10833:2017)
Ta slovenski standard je istoveten z: EN ISO 10833:2019
ICS:
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10833
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 1814:2005
English Version
Textile floor coverings - Determination of resistance to
damage at cut edges using the modified Vettermann drum
test (ISO 10833:2017)
Revêtements de sol textiles - Détermination de la Textile Bodenbeläge - Bestimmung der
résistance des joints par l'essai au tambour Schnittkantenfestigkeit mit der modifizierten
Vettermann modifié (ISO 10833:2017) Vettermann-Trommelprüfung (ISO 10833:2017)
This European Standard was approved by CEN on 8 April 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10833:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 10833:2017 has been prepared by Technical Committee ISO/TC 219 "Floor coverings” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 10833:2019
by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of
which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1814:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10833:2017 has been approved by CEN as EN ISO 10833:2019 without any modification.

INTERNATIONAL ISO
STANDARD 10833
Third edition
2017-05
Textile floor coverings —
Determination of resistance to
damage at cut edges using the
modified Vettermann drum test
Revêtements de sol textiles — Détermination de la résistance des
joints par l’essai au tambour Vettermann modifié
Reference number
ISO 10833:2017(E)
©
ISO 2017
ISO 10833:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 10833:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling and preparation of specimens . 3
6.1 Sampling . 3
6.1.1 General. 3
6.1.2 Sheet materials . 4
6.1.3 Tiles . 4
6.2 Preparation of specimens . 5
6.2.1 Sheet materials . 5
6.2.2 Tiles . 5
7 Atmosphere for conditioning and testing . 5
8 Procedures . 5
9 Assessment . 6
10 Test report . 6
ISO 10833:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 219, Floor coverings.
This third edition cancels and replaces the second edition (ISO 10833:2001), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the preparation (including the cutting) of the specimen in the case of sheet material have been
updated;
— the assessment and evaluation of the fraying resistance characteristic have been updated.
iv © ISO 2017 – All rights reserved

INTERNATIONAL STANDARD ISO 10833:2017(E)
Textile floor coverings — Determination of resistance
to damage at cut edges using the modified Vettermann
drum test
1 Scope
This document specifies a method to determine the susceptibility of textile floor coverings to
mechanical damage at cut edges.
It is applicable to all textile floor coverings both as sheet materials and as tiles.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 139, Textiles — Standard atmospheres for conditioning and testing
ISO 1957, Machine-made textile floor coverings — Selection and cutting of specimens for physical tests
ISO 2424, Textile floor coverings — Vocabulary
ISO 9405, Textile floor coverings — Assessment of changes in appearance
ISO 10361:2015, Textile floor coverings — Production of changes in appearance by means of Vettermann
drum and hexapod tumbler tester
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2424 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
delamination
separation of the use-surface and/or foundation/primary substrate of a textile floor covering from the
secondary backing
3.2
fraying
damage or loss of pile or substrate material of a textile floor covering from a cut edge
3.3
tufting out
loss of tufts from the use-surface of a textile floor covering
3.4
sprouting
release and appearance during use of extra-long tuft legs, which were accidentally trapped within the
pile of a textile floor covering during manufacture
ISO 10833:2017(E)
3.5
laddering
shooting
loss of consecutive loops of the same column from the use-surface of a textile floor cover
...