Gas supply systems - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional recommendations for renovation

This European standard describes specific functional recommendations for the renovation of pipeworks existing in gas supply systems and includes some requirements for materials other than plastics covered by CEN/TC 155 "Plastics piping and ducting systems". This European standard is intended to be applied in association with prEN 12007-1. This European Standard does not apply to pipework in above ground installations.

Gasversorgungssysteme - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 4: Besondere funktionale Empfehlungen für die Sanierung

Diese Europa(ische Norm beschreibt besondere funktionale Empfehlungen fu(r die Sanierung von Leitungsanlagen als Teil bestehender Gasversorgungssysteme. Sie entha(lt einige Werkstoffanforderungen, die nicht Kunststoff betreffen, soweit dieser von CEN/TC 155 "Kunststoff- und Abwasserrohrleitungssysteme" erfaßt wird. Diese Europa(ische Norm soll in Verbindung mit prEN 12007-1 angewendet werden. Diese Europa(ische Norm gilt nicht fu(r Leitungsanlagen in oberirdischen Anlagen.

Systèmes d'alimentation en gaz - Canalisations pour pression maximale de service inférieure ou égale à 16 bar - Partie 4: Recommandations fonctionnelles spécifiques pour la rénovation

La présente norme européenne décrit les recommandations fonctionnelles spécifiées pour la rénovation des tuyauteries existant dans les systèmes d' alimentation en gaz et comporte des prescriptions pour des matériaux autres que ceux en plastique couverts par le CEN/TC 155 "Systèmes de canalisations et de gaines en plastique". La présente norme européenne est destinée ` être appliquée en association avec le prEN 12007-1. La présente norme européenne ne s'applique pas ` la tuyauterie des installations hors sol.

Sistemi oskrbe s plinom - Cevovodni sistemi za najvišji delovni tlak do vključno 16 bar - 4. del: Posebna funkcionalna priporočila za obnovo

General Information

Status: Withdrawn
Publication Date: 18-Jan-2000
Withdrawal Date: 31-Jul-2012

ICS: 23.040.01 - Pipeline components and pipelines in general

Technical Committee: CEN/TC 234 - Gas infrastructure
Drafting Committee: CEN/TC 234/WG 2 - Gas supply systems up to and including 16 bar and pressure testing

Current Stage: 9960 - Withdrawal effective - Withdrawal
Start Date: 01-Aug-2012
Completion Date: 01-Aug-2012

Directive: 93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors

Mandate: M/017 - Standardization mandate to CEN in the field of equipment and installation for the transmission and distribution of gas

Ref Project: SIST EN 12007-4:2000 - Gas supply systems - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional recommendations for renovation

Relations

Replaced By: EN 12007-4:2012 - Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation
Effective Date: 08-Jun-2022

Standard

EN 12007-4:2000

English language

30 pages

Preview

e-Library read for

AI-Chat

1 day

Create e-Library subscription and get permanent access to the document. Subscriptions are available for: 23 23.040 23.040.01

Frequently Asked Questions

What is EN 12007-4:2000?

EN 12007-4:2000 is a standard published by the European Committee for Standardization (CEN). Its full title is "Gas supply systems - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional recommendations for renovation". This standard covers: This European standard describes specific functional recommendations for the renovation of pipeworks existing in gas supply systems and includes some requirements for materials other than plastics covered by CEN/TC 155 "Plastics piping and ducting systems". This European standard is intended to be applied in association with prEN 12007-1. This European Standard does not apply to pipework in above ground installations.

What is the scope of EN 12007-4:2000?

What ICS categories does EN 12007-4:2000 belong to?

EN 12007-4:2000 is classified under the following ICS (International Classification for Standards) categories: 23.040.01 - Pipeline components and pipelines in general. The ICS classification helps identify the subject area and facilitates finding related standards.

What standards are related to EN 12007-4:2000?

EN 12007-4:2000 has the following relationships with other standards: It is inter standard links to EN 12007-4:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

Is EN 12007-4:2000 a harmonized European standard?

EN 12007-4:2000 is associated with the following European legislation: EU Directives/Regulations: 93/38/EEC; Standardization Mandates: M/017. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.

How can I access EN 12007-4:2000?

EN 12007-4:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)

EN 12007-4:2000

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gasversorgungssysteme - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 4: Besondere funktionale Empfehlungen für die SanierungSystemes d'alimentation en gaz - Canalisations pour pression maximale de service inférieure ou égale a 16 bar - Partie 4: Recommandations fonctionnelles spécifiques pour la rénovationGas supply systems - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional recommendations for renovation91.140.40Sistemi za oskrbo s plinomGas supply systemsICS:Ta slovenski standard je istoveten z:EN 12007-4:2000SIST EN 12007-4:2000en01-julij-2000SIST EN 12007-
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

CEN

EN 12007-5:2024(Main)

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements

SIST EN 12007-5:2025

This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007 1 for:
a)   a maximum operating pressure (MOP) up to and including 16 bar;
b)   an operating temperature between −20 °C and +40 °C;
c)   gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line.
It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator’s nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve).
This document does not apply retrospectively to installations before the publication date unless specifically stated.
Specific functional requirements for:
—   polyethylene pipelines are given in EN 12007 2;
—   steel pipelines are given in EN 12007 3;
—   polyamide (PA-U) pipelines are given in CEN/TS 12007 6;
—   pipework for buildings are given in EN 1775;
—   pressure regulating installations are given in EN 12279 or EN 12186;
—   pressure testing, commissioning and decommissioning are given in EN 12327;
—   safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 gives:
—   description of legislations/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

Standard
31 pages
English language
e-Library read for
AI-Chat
1 day

CEN

EN 1594:2024(Main)

Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements

SIST EN 1594:2024

This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1   Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
-   onshore:
-   from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
-   high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
-   steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
-   gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2   The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

Standard
69 pages
English language
e-Library read for
AI-Chat
1 day

CEN

EN 15001-1:2023(Main)

Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing

SIST EN 15001-1:2023

This European Standard specifies detailed functional requirements for the design, selection of materials, construction, inspection and testing of:
-   industrial gas installation pipework and assemblies with an operating pressure greater than 0,5 bar; and
-   non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings;
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE 1   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between −20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 (all parts) for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar in buildings, EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this standard applies.
In this European Standard, the term “gas“ refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure (normal conditions). These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in EN 437:2003+A1:2009, Table 1. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 "Gas infrastructure - Quality of gas - Group H";
-   vaporized LPG;
-   biomethane, complying with EN 16723 1;
-   vaporized LNG.
NOTE 2   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009.
LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure in the liquid state (e.g. between the storage vessel and any pressure regulator).
In this standard, all pressures are gauge pressures unless otherwise stated.
This standard has been harmonized to address the essential safety requirements of the Pressure Equipment Directive (PED, 2014/68/EU [formerly 97/23/EC]) relevant for the joining of gas installation pipework (assemblies) falling within the scope of the PED. These are listed in Annex ZA. However, "this Directive does not cover the assembly of pressure equipment on the site and under the responsibility of the user, as in the case of industrial installations" (PED, Preamble, 7th recital, last paragraph).
Although in this respect, the standard takes into account the essential safety requirements of the PED, no inference can be drawn from this as to whether or not the installation or parts of the installation falls within the scope of the PED. Reference should therefore be made to the PED and relevant national legislation.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware (...)

Standard
131 pages
English language
e-Library read for
AI-Chat
1 day

CEN

EN 15001-2:2023(Main)

Gas supply systems - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance

SIST EN 15001-2:2023

This European Standard specifies detailed functional requirements for the commissioning, operation and maintenance of
-   industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of
-   non-industrial gas installations (residential and commercial) with an operating pressure greater than 5 bar,
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This European Standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between -20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this European Standard applies.
In this European Standard, the term "gas" refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure. These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in Table 1 of EN 437:2003+A1:2009. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 -Gas infrastructure - Quality of gas - Group H”,
-   vaporized LNG,
-   biomethane, complying with EN 16723-1,
-   vaporized LNG.
NOTE   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009. LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure (e.g. between the storage vessel and its pressure regulator).
In this European Standard, all pressures are gauge pressures unless otherwise stated.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
For gas installations within the scope of this standard, national legislation and regulations have to be taken into account.
Functional requirements for design, selection of materials, construction, inspection and testing of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of gas installations greater than 5 bar in buildings and areas intended for residential, commercial, public and mixed uses are described in EN 15001-1.
Generally, additional safety precautions may be necessary where non odorized gas is used. For non-industrial purposes, the gas should be odorized.

Standard
26 pages
English language
e-Library read for
AI-Chat
1 day

CEN

EN 17649:2022(Main)

Gas infrastructure - Safety Management System (SMS) and Pipeline Integrity Management System (PIMS) - Functional requirements

SIST EN 17649:2022

This document specifies requirements on the development and implementation of a Safety Management System (SMS) and a Pipeline Integrity Management System (PIMS). The SMS is applicable for system operators of a gas infrastructure. The PIMS is applicable for system operators of gas infrastructure with a maximum operating pressure (MOP) over 16 bar.
This document refers to all activities and processes related to safety aspects and performed by system operators of a gas infrastructure, including those activities entrusted to contractors. It includes safety-related provisions on operation of the gas infrastructure.
This document is applicable to infrastructure for the conveyance of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 and gases such as biomethane and hydrogen and to mixtures of these gases with natural gas.
This document covers also gases classified as group H, that are to be transmitted, injected into and from storages, distributed and utilized, as specified in EN 16726. For the requirements and test methods for biomethane at the point of entry into a natural gas network, reference is made to EN 16723-1.
This document can be applied for gas infrastructure conveying gases of the 3rd gas family as classified in EN 437 or for other gases such as carbon dioxide.
Specific requirements for occupational health and safety are excluded from this document. For these, other European and/or international standards, e.g. ISO 45001, apply.
This document specifies common basic principles for gas infrastructure. It is important that users of this document are expected to be aware that more detailed national standards and/or codes of practice exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE CEN/TR 13737 (all parts) contains:
- clarification of relevant legislation/regulations applicable in a country;
- if appropriate, more restrictive national requirements;
- national contact points for the latest information.

Standard
38 pages
English language
e-Library read for
AI-Chat
1 day

CEN

CEN/TR 16787:2014(Main)

Industrial Gas Installation - Guideline

SIST-TP CEN/TR 16787:2015

This Technical Report applies to safety and operational topics for equipment and pipework systems installed within industrial premises which may be used for process and non-process applications such as Heating, Power Generation, Incineration, etc.
It is applicable to a range of combustible gases used within an industrial environment. The gas plant may include normal combustion with air and/or oxygen, catalytic oxidation or cracking (e.g. as in a refinery).
The user of gas equipment and pipework systems has a responsibility to ensure the safety of the design, of plant operation and plant maintenance.
For piped supplies of gas to a site this Technical Report applies to the system downstream of the ‘point of delivery’. The term, ‘point of delivery’ refers to the isolation valve (or combination of regulator and isolation valve) located before or after the metering station, as will be defined by the particular EU member state national legislation.
The guidance in this Technical Report may also apply to gases generated for the sites own use, such as coke oven gas, site bio-gas plant, site LPG/air plant etc.

Technical report
57 pages
English language
e-Library read for
AI-Chat
1 day
Technical report
57 pages
English language
e-Library read for
AI-Chat
1 day

CEN

EN 12007-1:2012(Main)

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements

SIST EN 12007-1:2013

This European Standard describes the general functional requirements for pipelines up to the point of delivery, and also for buried sections of pipework after the point of delivery, for maximum operating pressures up to and including 16 bar for gaseous fuels in accordance with EN 437:1993+A1:2009, Table 1. It applies to their design, construction, commissioning, decommissioning, operation, maintenance, renovation, extension and other associated works.
This European Standard does not apply to the materials, design, construction, testing and commissioning of gas infrastructures in use prior to the publication of this European Standard. However, this European Standard does apply to the operation, maintenance, renovation and extension of all gas infrastructures.
Specific functional requirements for polyethylene pipelines are given in EN 12007-2, for steel pipelines in EN 12007-3 and for the renovation of pipelines in EN 12007-4. Functional recommendations for pipework for buildings are given in EN 1775. Functional requirements for service lines are given in prEN 12007-5.
Functional requirements for pressure testing, commissioning and decommissioning are given in EN 12327.
Functional requirements for measuring systems are given in EN 1776.
Functional requirements for pressure regulating stations are given in EN 12186.
Functional requirements for pressure regulating installations are given in EN 12279.
Functional requirements for gas transmission are given in EN 1594.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation should take precedence as illustrated in FprCEN/TR 13737-1.
FprCEN/TR 13737-1 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

Standard
30 pages
English language
e-Library read for
AI-Chat
1 day

31-Jul-2012
27-Feb-2013
23.040.01
M/017
M/617
CEN/TC 234

CEN

EN 12007-4:2012(Main)

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation

SIST EN 12007-4:2013

This European Standard describes specific functional requirements for the renovation of pipework in existing gas infrastructures. This European Standard is intended to be applied with the requirements of EN 12007-1.
This European Standard does not apply to pipework in above ground installations.
This European Standard covers the various renovation technologies for gas piping in the range of sizes covering gas mains and gas service lines and is intended to be applied in association with EN 12007-1. Certain pipe networks originally for other purposes can be considered for renovation technologies to make them suitable for gas infrastructure.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation should take precedence as illustrated in FprCEN/TR 13737-1.
FprCEN/TR 13737-1 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.