Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 2: Requirements for testing and marking of separation efficiency (ISO 21904-2:2020)

This document specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements.
The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intended to be used.
This document applies to equipment that is manufactured after its publication.
NOTE       General ventilation systems are excluded from the Scope of ISO 21904-1.

Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren - Einrichtungen zum Erfassen und Abscheiden von Schweißrauch - Teil 2: Anforderungen an Prüfung und Kennzeichnung des Abscheidegrades (ISO 21904-2:2020)

Dieses Dokument legt ein Verfahren für die Prüfung von Einrichtungen zum Abscheiden von Schweißrauch fest, um zu ermitteln, ob die Geräte die hinsichtlich der Abscheideleistung festgelegten Anforderungen erfüllen.
Das hier beschriebene Verfahren ist nicht anwendbar auf die Prüfung von Filterpatronen bzw. -kassetten, losgelöst von den Einrichtungen, in denen sie verwendet werden sollen.
Dieses Dokument gilt für Maschinen, die nach Veröffentlichung dieser Norm hergestellt wurden.
ANMERKUNG   In ISO 21904-1 sind allgemeine Belüftungssysteme vom Anwendungsbereich ausgenommen.

Hygiène et sécurité en soudage et techniques connexes - Équipements de captage et de filtration des fumées - Partie 2: Exigences relatives aux essais et marquage de l'efficacité de séparation (ISO 21904-2:2020)

Le présent document spécifie une méthode d'essai de l'équipement de filtration de fumées de soudage dans le but de déterminer si son efficacité de séparation satisfait aux exigences spécifiées.
La méthode spécifiée n'est pas applicable aux essais des cartouches filtrantes indépendantes de l'équipement dans lequel elles sont destinées à être utilisées.
Le présent document est applicable aux équipements fabriqués après sa date de publication.
NOTE       Les systèmes de ventilation générale sont exclus du domaine d'application de l'ISO 21904-1.

Zdravje in varnost pri varjenju in sorodnih postopkih - Oprema za zajem in ločevanje varilnega dima - 2. del: Zahteve za preskušanje in označevanje učinkovitosti ločevanja (ISO 21904-2:2020)

General Information

Status
Published
Publication Date
10-Mar-2020
Withdrawal Date
29-Sep-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Mar-2020
Completion Date
11-Mar-2020

Relations

Buy Standard

Standard
EN ISO 21904-2:2020
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2020
Nadomešča:
SIST EN ISO 15012-1:2013
Zdravje in varnost pri varjenju in sorodnih postopkih - Oprema za zajem in
ločevanje varilnega dima - 2. del: Zahteve za preskušanje in označevanje
učinkovitosti ločevanja (ISO 21904-2:2020)
Health and safety in welding and allied processes - Equipment for capture and
separation of welding fume - Part 2: Requirements for testing and marking of separation
efficiency (ISO 21904-2:2020)
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren -
Einrichtungen zum Erfassen und Abscheiden von Schweißrauch - Teil 2: Anforderungen
an Prüfung des Abscheidegrades (ISO 21904-2:2020)
Hygiène et sécurité en soudage et techniques connexes - Équipements de captage et de
filtration des fumées - Partie 2: Exigences relatives aux essais et marquage de l'efficacité
de séparation (ISO 21904-2:2020)
Ta slovenski standard je istoveten z: EN ISO 21904-2:2020
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.160.30 Varilna oprema Welding equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 21904-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 25.160.01; 13.100 Supersedes EN ISO 15012-1:2013
English Version
Health and safety in welding and allied processes -
Equipment for capture and separation of welding fume -
Part 2: Requirements for testing and marking of
separation efficiency (ISO 21904-2:2020)
Hygiène et sécurité en soudage et techniques connexes Arbeits- und Gesundheitsschutz beim Schweißen und
- Équipements de captage et de filtration des fumées - bei verwandten Verfahren - Einrichtungen zum
Partie 2: Exigences relatives aux essais et marquage de Erfassen und Abscheiden von Schweißrauch - Teil 2:
l'efficacité de séparation (ISO 21904-2:2020) Anforderungen an Prüfung des Abscheidegrades (ISO
21904-2:2020)
This European Standard was approved by CEN on 20 January 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21904-2:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 21904-2:2020) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15012-1:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 21904-2:2020 has been approved by CEN as EN ISO 21904-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 21904-2
First edition
2020-02
Health and safety in welding and allied
processes — Equipment for capture
and separation of welding fume —
Part 2:
Requirements for testing and marking
of separation efficiency
Hygiène et sécurité en soudage et techniques connexes —
Équipements de captage et de filtration des fumées —
Partie 2: Exigences relatives aux essais et marquage de l'efficacité de
séparation
Reference number
ISO 21904-2:2020(E)
©
ISO 2020
ISO 21904-2:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 21904-2:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test method . 5
6.1 Selection of test arrangement . 5
6.2 Test conditions . 5
6.3 Procedure . 5
6.3.1 Source emission rate measurement . 5
6.3.2 Equipment without filter cleaning system . 5
6.3.3 Equipment with manually initiated filter cleaning system . 7
6.3.4 Equipment with automatically initiated filter cleaning system . 7
6.3.5 Equipment with electrostatic precipitators . 8
6.4 Calculation of the separation efficiency . 9
7 Accuracy of measurement . 9
8 Test report . 9
Annex A (informative) Test cabin .11
Annex B (informative) Welding fume source .12
Bibliography .14
ISO 21904-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www. iso. org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www. iso. org/patents ).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www. iso. org/
iso/foreword . html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 9, Health and safety.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www. iso. org/members . html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee. iso. org/sites/ tc 44/ home/interpretation . html.
A list of all parts in the ISO 21904 series can be found on the ISO website.
This first edition cancels and replaces ISO 15012-1.
iv © ISO 2020 – All rights reserved

ISO 21904-2:2020(E)
Introduction
It is common practice in the fabrication industry to control exposure to welding fume using local exhaust
ventilation equipment that, following capture and separation of the fume, returns the extracted air to
the workplace or exhausts it to the atmosphere. It is important that such equipment has high separation
efficiency so that as little fume as possible is recirculated or exhausted. This document has therefore
been developed to specify a test method for determining the efficiency of welding fume separation
equipment and the requirements of the test method.
---------------------- Pa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.