ASTM D5207-20
(Practice)Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials
Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials
SIGNIFICANCE AND USE
5.1 The flame height and color (indicative of air-to-gas ratio) for a test flame have traditionally been specified in the individual test method. The energy content of the flame has also been addressed by reference to a specific supply gas. It has been determined that the supply-gas back pressure and flow rate can be varied without affecting the height and color of the flame. However, the energy content of the flame is affected. This practice provides the back pressure and flow rate of the supply gas for a 20-mm (50-W) and a 125-mm (500-W) test flame, and a procedure for confirming the heat-evolution profile of the test flame.
5.2 Information is provided for test flames using methane, propane, or butane. Using this information, these supply gases have the capability to be used interchangeably with a standardized burner to produce essentially the same test flame.
SCOPE
1.1 This practice covers the confirmation of test flames for small-scale burning tests on plastic materials using the laboratory burner described in Specification D5025. Back pressures and flow rates for methane, propane, and butane supply gases are given for specific test flames. This practice describes a procedure to confirm the heat evolution of the test flame.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
Note 1: There is no similar ISO standard. This practice is equivalent in technical content to, but not fully corresponding in presentation with, the confirmatory procedures of IEC/TS 60695-11-3, Method A and IEC/TS 60695-11-4, Method A.
1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D5207 −20
Standard Practice for
Confirmation of 20-mm (50-W) and 125-mm (500-W) Test
1
Flames for Small-Scale Burning Tests on Plastic Materials
This standard is issued under the fixed designation D5207; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This practice covers the confirmation of test flames for
D883 Terminology Relating to Plastics
small-scale burning tests on plastic materials using the labora-
D3195 Practice for Rotameter Calibration
tory burner described in Specification D5025. Back pressures
D5025 Specification for Laboratory Burner Used for Small-
and flow rates for methane, propane, and butane supply gases
Scale Burning Tests on Plastic Materials
are given for specific test flames. This practice describes a
E176 Terminology of Fire Standards
procedure to confirm the heat evolution of the test flame.
E220 Test Method for Calibration of Thermocouples By
1.2 The values stated in SI units are to be regarded as the
Comparison Techniques
standard.
E230 Specification for Temperature-Electromotive Force
(emf) Tables for Standardized Thermocouples
1.3 This standard is used to measure and describe the
E608 Specification for Mineral-Insulated, Metal-Sheathed
response of materials, products, or assemblies to heat and
Base Metal Thermocouples
flame under controlled conditions, but does not by itself
3
2.2 IEC Standards:
incorporate all factors required for fire hazard or fire risk
IEC 60695-11-3 Fire Hazard Testing – Part 11-3: Test
assessment of the materials, products, or assemblies under
Flames – 500 W Flames – Apparatus and Confirmational
actual fire conditions.
Test Methods
NOTE 1—There is no similar ISO standard. This practice is equivalent IEC 60695-11-4 Fire Hazard Testing – Part 11-4: Test
in technical content to, but not fully corresponding in presentation with,
Flames – 50 W Flame – Apparatus and Confirmational
the confirmatory procedures of IEC/TS 60695-11-3, Method A and IEC/
Test Methods
TS 60695-11-4, Method A.
3. Terminology
1.4 Fire testing is inherently hazardous. Adequate safe-
guards for personnel and property shall be employed in
3.1 Definitions of Terms:
conducting these tests.
3.1.1 For definitions of terms related to plastics used in this
test method, refer to Terminology D883. For definitions of
1.5 This standard does not purport to address all of the
terms related to fire used in this test method, refer to Termi-
safety concerns, if any, associated with its use. It is the
nology E176.
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
4. Summary of Practice
mine the applicability of regulatory limitations prior to use.
4.1 A test flame of specified height and color is obtained
1.6 This international standard was developed in accor-
with gas supplied at a suggested back pressure and flow rate.A
dance with internationally recognized principles on standard-
thermal sensor is then positioned over the flame, and the time
ization established in the Decision on Principles for the
forthetemperatureofthesensortoincreasefrom100to700°C
Development of International Standards, Guides and Recom-
is determined. The time is used to confirm the heat-evolution
mendations issued by the World Trade Organization Technical
profile of the test flame.
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This practice is under the jurisdiction ofASTM Committee D20 on Plastics and contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
is the direct responsibility of Subcommittee D20.30 on Thermal Properties. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 1, 2020. Published December 2020. Originally the ASTM website.
3
approved in 1991. Last previous edition approved in 2014 as D5207 – 14. DOI: Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
10.1520/D5207-20. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5207−20
5. Significance and Use 6.4 Flow Meter—Arotameter calibrated in accordance with
PracticeD3195,withcorrela
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5207 − 14 D5207 − 20
Standard Practice for
Confirmation of 20–mm (50–W) and 125–mm (500–W)20-mm
(50-W) and 125-mm (500-W) Test Flames for Small-Scale
1
Burning Tests on Plastic Materials
This standard is issued under the fixed designation D5207; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice covers the confirmation of test flames for small-scale burning tests on plastic materials using the laboratory
burner described in Specification D5025. Back pressures and flow rates for methane, propane, and butane supply gases are given
for specific test flames. This practice describes a procedure to confirm the heat evolution of the test flame.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials,
products, or assemblies under actual fire conditions.
NOTE 1—There is no similar ISO standard. This practice is equivalent in technical content to, but not fully corresponding in presentation with, the
confirmatory procedures of IEC/TS 60695-11-3, Method A and IEC/TS 60695-11-4, Method A.
1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these
tests.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of
the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This practice is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.30 on Thermal Properties.
Current edition approved May 1, 2014Dec. 1, 2020. Published May 2014December 2020. Originally approved in 1991. Last previous edition approved in 20092014 as
D5207 – 09.D5207 – 14. DOI: 10.1520/D5207-14.10.1520/D5207-20.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5207 − 20
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
D3195 Practice for Rotameter Calibration
D5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
E176 Terminology of Fire Standards
E220 Test Method for Calibration of Thermocouples By Comparison Techniques
E230 Specification for Temperature-Electromotive Force (emf) Tables for Standardized Thermocouples
E608 Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples
3
2.2 IEC Standards:
IEC/TS 60695-11-3IEC 60695-11-3 Ed. 1: Fire Hazard Testing-Part 11: Test Flames-Section 3: 500 W Flames: Testing – Part
11-3: Test Flames – 500 W Flames – Apparatus and Confirmational Test Methods
IEC/TS 60695-11-4IEC 60695-11-4 Ed. 2: Fire Hazard Testing-Part 11: Test Flames-Section 4: 50 W Flame: Testing – Part 11-4:
Test Flames – 50 W Flame – Apparatus and Confirmational Test Methods
3. Terminology
3.1 Definitions of Terms:
3.1.1 For definitions of terms related to plastics used in this test method, refer to Terminology D883. For definitions of terms
related to fire used in this test method, refer to Terminology E176.
4. Summary of Practice
4.1 A test flame of specified height and color is obtained with gas supplied at a suggested back pressure and flow rate. A thermal
sensor is then positioned over
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.