ASTM C1433M-22
(Specification)Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)
Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)
ABSTRACT
This specification deals with the standards for single-cell precast reinforced concrete box sections cast monolithically and proposed for use in the construction of culverts and for the conveyance of storm water industrial sewage. The reinforced concrete shall be composed of cementitious materials, mineral aggregates and water, in which steel has been embedded. The aggregates shall be sized, graded, and mixed to the proportion that will produce a homogeneous mixture. The box sections shall also undergo steam curing, water curing, and membrane curing.
SCOPE
1.1 This specification covers single-cell precast reinforced concrete box sections cast monolithically and intended to be used for the construction of culverts and for the conveyance of storm water industrial wastes and sewage.
1.2 This specification is the SI companion to Specification C1433.
Note 1: This specification is primarily a manufacturing and purchasing specification. However, standard designs are included and the criteria used to develop these designs are given in Appendix X1. The successful performance of this product depends upon the proper selection of the box section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete box sections specified herein is cautioned that he must properly correlate the loading conditions and the field requirements with the box section specified and provide for inspection at the construction site.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1433M −22
Standard Specification for
Precast Reinforced Concrete Monolithic Box Sections for
1
Culverts, Storm Drains, and Sewers (Metric)
This standard is issued under the fixed designation C1433M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Specimens in the Field
C33/C33MSpecification for Concrete Aggregates
1.1 This specification covers single-cell precast reinforced
C39/C39MTest Method for Compressive Strength of Cylin-
concrete box sections cast monolithically and intended to be
drical Concrete Specimens
used for the construction of culverts and for the conveyance of
C150/C150MSpecification for Portland Cement
storm water industrial wastes and sewage.
C260/C260MSpecification for Air-Entraining Admixtures
1.2 This specification is the SI companion to Specification
for Concrete
C1433.
C309Specification for Liquid Membrane-Forming Com-
pounds for Curing Concrete
NOTE 1—This specification is primarily a manufacturing and purchas-
ing specification. However, standard designs are included and the criteria C494/C494MSpecification for Chemical Admixtures for
used to develop these designs are given in Appendix X1. The successful
Concrete
performance of this product depends upon the proper selection of the box
C497MTest Methods for Concrete Pipe, Concrete Box
section, bedding, backfill, and care that the installation conforms to the
Sections, Manhole Sections, or Tile (Metric)
construction specifications. The purchaser of the precast reinforced
C595/C595MSpecification for Blended Hydraulic Cements
concrete box sections specified herein is cautioned that he must properly
correlate the loading conditions and the field requirements with the box
C618Specification for Coal Fly Ash and Raw or Calcined
section specified and provide for inspection at the construction site.
Natural Pozzolan for Use in Concrete
1.3 This international standard was developed in accor-
C822Terminology Relating to Concrete Pipe and Related
dance with internationally recognized principles on standard-
Products
ization established in the Decision on Principles for the
C989/C989MSpecification for Slag Cement for Use in
Development of International Standards, Guides and Recom-
Concrete and Mortars
mendations issued by the World Trade Organization Technical
C990Specification for Joints for Concrete Pipe, Manholes,
Barriers to Trade (TBT) Committee.
and Precast Box Sections Using Preformed Flexible Joint
Sealants
2. Referenced Documents
C1017/C1017MSpecification for Chemical Admixtures for
3
2
Use in Producing Flowing Concrete (Withdrawn 2022)
2.1 ASTM Standards:
C1116/C1116MSpecification for Fiber-Reinforced Concrete
A615/A615MSpecificationforDeformedandPlainCarbon-
C1602/C1602MSpecification for Mixing Water Used in the
Steel Bars for Concrete Reinforcement
Production of Hydraulic Cement Concrete
A1064/A1064MSpecification for Carbon-Steel Wire and
C1619Specification for Elastomeric Seals for Joining Con-
Welded Wire Reinforcement, Plain and Deformed, for
crete Structures
Concrete
C1675Practice for Installation of Precast Reinforced Con-
A706/A706MSpecification for Deformed and Plain Low-
creteMonolithicBoxSectionsforCulverts,StormDrains,
Alloy Steel Bars for Concrete Reinforcement
and Sewers
C31/C31MPractice for Making and Curing Concrete Test
C1677Specification for Joints for Concrete Box, Using
Rubber Gaskets
1
This specification is under the jurisdiction of ASTM Committee C13 on
4
2.2 AASHTO Standards:
Concrete Pipe and is the direct responsibility of Subcommittee C13.07 on
Standard Specifications for Highway Bridges
Acceptance Specifications and Precast Concrete Box Sections.
Current edition approved Sept. 1, 2022. Published October 2022. Originally
approved in 1999. Last previous edition approved in 2020 as C1433M–20. DOI:
10.1520/C1433M-22.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or The last approved version of this historical standard is referenced on
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.astm.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from American Association of State Highway and Transportation
the ASTM website. Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Unite
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1433M − 20 C1433M − 22
Standard Specification for
Precast Reinforced Concrete Monolithic Box Sections for
1
Culverts, Storm Drains, and Sewers (Metric)
This standard is issued under the fixed designation C1433M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers single-cell precast reinforced concrete box sections cast monolithically and intended to be used for
the construction of culverts and for the conveyance of storm water industrial wastes and sewage.
1.2 This specification is the SI companion to Specification C1433.
NOTE 1—This specification is primarily a manufacturing and purchasing specification. However, standard designs are included and the criteria used to
develop these designs are given in Appendix X1. The successful performance of this product depends upon the proper selection of the box section,
bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete box sections
specified herein is cautioned that he must properly correlate the loading conditions and the field requirements with the box section specified and provide
for inspection at the construction site.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C150/C150M Specification for Portland Cement
C260/C260M Specification for Air-Entraining Admixtures for Concrete
C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C497M Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile (Metric)
C595/C595M Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.07 on Acceptance
Specifications and Precast Concrete Box Sections.
Current edition approved Sept. 15, 2020Sept. 1, 2022. Published November 2020October 2022. Originally approved in 1999. Last previous edition approved in 20192020
as C1433M – 19.C1433M – 20. DOI: 10.1520/C1433M-20.10.1520/C1433M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1433M − 22
C822 Terminology Relating to Concrete Pipe and Related Products
C989/C989M Specification for Slag Cement for Use in Concrete and Mortars
C990 Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
3
C1017/C1017M Specification for Chemical Admixtures for Use in Producing Flowing Concrete (Withdrawn 2022)
C1116/C1116M Specification for Fiber-Reinforced Concrete
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
C1619 Specification for Elastomeric Seals for Joining Concrete Structures
C1675 Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers
C1677 Specification for Joints for Concrete Box, Using Rubber Gaskets
4
2.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.