ASTM D1152-06

Designation: D1152 −06
Standard Specification for
1
Methanol (Methyl Alcohol)
This standard is issued under the fixed designation D1152; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E300 Practice for Sampling Industrial Chemicals
E346 Test Methods for Analysis of Methanol
1.1 This specification covers methanol (99.85 % grade).
2.2 U.S. Fed. Specification:
1.2 The following applies to all specified limits in this
PPP-C-2020 Federal Specification Packaging of Chemicals,
standard; for purposes of determining conformance with this
3
Liquid, Dry, and Paste
standard, an observed value or a calculated value shall be
rounded off “to the nearest unit” in the last right-hand digit
3. Properties
used in expressing the specification limit, in accordance with
3.1 Methanol (99.85 % grade) shall conform to the follow-
the rounding-off method of Practice E29.
ing requirements:
1.3 The values stated in SI units are to be regarded as
Apparent specific
standard. No other units of measurement are included in this
gravity:
20/20°C 0.7920 to 0.7930
standard.
or
1.4 For specific hazard information and guidance, see the
25/25°C 0.7883 to 0.7893
Color, Pt-Co, max (see Note 2) 10
supplier’sMaterialSafetyDataSheetformaterialslistedinthis
Distillation range, °C, max 1.0 (to include 64.6 ± 0.1)
specification.
Nonvolatile matter, mg/100 5
mL, max
1.5 This standard does not purport to address all of the
Odor (see Note 1) nonresidual
safety concerns, if any, associated with its use. It is the
Water, weight %, max 0.10
responsibility of the user of this standard to establish appro- Acidity (free acid as acetic 0.003, equivalent to 0.028 mg KOH per gram
acid), weight %, max of material
priate safety and health practices and determine the applica-
Acetone, weight %, max 0.003
bility of regulatory limitations prior to use.
Sulfuric acid wash test 50
(carbonizable impurities)
2. Referenced Documents Color, Pt-Co, max
Permanganate time, min 50
2
2.1 ASTM Standards:
NOTE 1—Optional: Test for odor only when agreed upon as necessary
D1209 Test Method for Color of Clear Liquids (Platinum-
between the purchaser and the supplier.
Cobalt Scale)
NOTE 2—Instrumental Pt-Co color determined by Test Method D5386
D1296 Test Method for Odor of Volatile Solvents and
have been shown to have no statistically significant difference from Pt-Co
Diluents color determined by Test Method D1209. However, it is not known
whether methanol was part of the sample set included in the interlabora-
D1353 Test Method for Nonvolatile Matter in Volatile Sol-
tory study.
vents for Use in Paint, Varnish, Lacquer, and Related
Products
4. Sampling
D5386 Test Method for Color of Liquids Using Tristimulus
4.1 Sample the material in accordance with Practice E300.
Colorimetry
E29 Practice for Using Significant Digits in Test Data to
5. Test Methods
Determine Conformance with Specifications
5.1 The properties enumerated in this specification shall be
determined in accordance with Test Methods E346 and the
1
This specification is under the jurisdiction of ASTM Committee D01 on Paint
following methods:
and Related Coatings, Material
...