Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers

ABSTRACT
This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial, residential, agricultural, and highway drainage, including installation under parking lots and roadways. Chambers are produced in arch shapes with dimensions based on chamber rise, chamber span, and wall stiffness. They are manufactured with integral feet that provide base support. They may include perforations to enhance water flow and must meet test requirements for arch stiffness, flattening, and accelerated weathering. The successful performance of the product depends upon the type and depth of bedding and backfill, and care in installation. This specification includes requirements for the manufacturer to provide chamber installation instructions to the purchaser.
SCOPE
1.1 This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial, residential, agricultural, and highway drainage, including installation under parking lots and roadways.  
1.2 Chambers are produced in arch shapes with dimensions based on chamber rise, chamber span, and wall stiffness. Chambers are manufactured with integral feet that provide base support. Chambers may include perforations to enhance water flow. Chambers must meet test requirements for arch stiffness, flattening, and accelerated weathering.  
1.3 Analysis and experience have shown that the successful performance of this product depends upon the type and depth of bedding and backfill, and care in installation. This specification includes requirements for the manufacturer to provide chamber installation instructions to the purchaser.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address water quality issues or hydraulic performance requirements associated with its use. It is the responsibility of the user to ensure that appropriate engineering analysis is performed to evaluate the water quality issues and hydraulic performance requirements for each installation.  
1.6 The following safety hazards caveat pertains only to the test method portion, Section 6, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Mar-2016
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM F2418-16 - Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM F2418-16 - Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2418 −16
StandardSpecification for
Polypropylene (PP) Corrugated Wall Stormwater Collection
1
Chambers
This standard is issued under the fixed designation F2418; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
1.1 This specification covers requirements, test methods,
of this standard to establish appropriate safety and health
materials, and marking for polypropylene (PP), open bottom,
practices and determine the applicability of regulatory limita-
buried chambers of corrugated wall construction used for
tions prior to use.
collection, detention, and retention of stormwater runoff. Ap-
plications include commercial, residential, agricultural, and
2. Referenced Documents
highwaydrainage,includinginstallationunderparkinglotsand
2
2.1 ASTM Standards:
roadways.
D256 Test Methods for Determining the Izod Pendulum
1.2 Chambers are produced in arch shapes with dimensions
Impact Resistance of Plastics
based on chamber rise, chamber span, and wall stiffness.
D618 Practice for Conditioning Plastics for Testing
Chambersaremanufacturedwithintegralfeetthatprovidebase
D638 Test Method for Tensile Properties of Plastics
support. Chambers may include perforations to enhance water
D790 Test Methods for Flexural Properties of Unreinforced
flow. Chambers must meet test requirements for arch stiffness,
and Reinforced Plastics and Electrical Insulating Materi-
flattening, and accelerated weathering.
als
1.3 Analysis and experience have shown that the successful D1600 Terminology forAbbreviatedTerms Relating to Plas-
performance of this product depends upon the type and depth
tics
of bedding and backfill, and care in installation. This specifi- D2122 Test Method for Determining Dimensions of Ther-
cation includes requirements for the manufacturer to provide
moplastic Pipe and Fittings
chamber installation instructions to the purchaser.
D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.4 The values stated in inch-pound units are to be regarded
D2990 Test Methods for Tensile, Compressive, and Flexural
as standard. The values given in parentheses are mathematical
Creep and Creep-Rupture of Plastics
conversions to SI units that are provided for information only
D4101 Specification for Polypropylene Injection and Extru-
and are not considered standard.
sion Materials
1.5 This standard does not purport to address water quality
D4329 Practice for Fluorescent Ultraviolet (UV) Lamp Ap-
issues or hydraulic performance requirements associated with
paratus Exposure of Plastics
its use. It is the responsibility of the user to ensure that
D6992 Test Method for Accelerated Tensile Creep and
appropriate engineering analysis is performed to evaluate the
Creep-Rupture of Geosynthetic Materials Based on Time-
water quality issues and hydraulic performance requirements
Temperature Superposition Using the Stepped Isothermal
for each installation.
Method
1.6 The following safety hazards caveat pertains only to the
F412 Terminology Relating to Plastic Piping Systems
test method portion, Section 6, of this specification: This
F2787 Practice for Structural Design of Thermoplastic Cor-
rugated Wall Stormwater Collection Chambers
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
2
Drainage. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2016. Published June 2016. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2004. Last previous edition approved in 2013 as F2418-13. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2418-16. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2418−16
3. Terminology 3.1.12 rise—the vertical distance from the chamber base
(bottom of the chamber foot) to the inside of a chamber wall
3.1 Definitions:
valley element at the crown as depicted in Fig. 1.
3.1.1 Definitions used in this specification are in accordance
3.1.13 span—the horizontal distance from the interior of
with the definitions in Terminology F412, and abbreviations
one sidewall valley elem
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2418 − 13 F2418 − 16
Standard Specification for
Polypropylene (PP) Corrugated Wall Stormwater Collection
1
Chambers
This standard is issued under the fixed designation F2418; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried
chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include
commercial, residential, agricultural, and highway drainage, including installation under parking lots and roadways.
1.2 Chambers are produced in arch shapes with dimensions based on chamber rise, chamber span, and wall stiffness. Chambers
are manufactured with integral feet that provide base support. Chambers may include perforations to enhance water flow.
Chambers must meet test requirements for arch stiffness, flattening, and accelerated weathering.
1.3 Analysis and experience have shown that the successful performance of this product depends upon the type and depth of
bedding and backfill, and care in installation. This specification includes requirements for the manufacturer to provide chamber
installation instructions to the purchaser.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address water quality issues or hydraulic performance requirements associated with its
use. It is the responsibility of the user to ensure that appropriate engineering analysis is performed to evaluate the water quality
issues and hydraulic performance requirements for each installation.
1.6 The following safety hazards caveat pertains only to the test method portion, Section 6, of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D4101 Specification for Polypropylene Injection and Extrusion Materials
D4329 Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
D6992 Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature
Superposition Using the Stepped Isothermal Method
F412 Terminology Relating to Plastic Piping Systems
F2787 Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land Drainage.
Current edition approved Aug. 1, 2013April 1, 2016. Published August 2013June 2016. Originally approved in 2004. Last previous edition approved in 20122013 as
F2418-12.-13. DOI: 10.1520/F2418-13.10.1520/F2418-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2418 − 16
3. Terminology
3.1 Definitions:
3.1.1 Definitions used in thi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.