iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5871-06

(Specification)

Standard Specification for Benzene for Cyclohexane Feedstock

Standard Specification for Benzene for Cyclohexane Feedstock

SCOPE
1.1 This specification covers benzene for cyclohexane feedstock.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.3 Consult current OSHA regulations supplier's Material Safety Data Sheets for all materials used in this specification.

General Information

Status
Historical
Publication Date
30-Sep-2006
ICS
71.040.01 - Analytical chemistry in general
71.080.01 - Organic chemicals in general
Technical Committee
D16 - Aromatic, Industrial, Specialty and Related Chemicals
Drafting Committee
D16.01 - Benzene, Toluene, Xylenes, Cyclohexane and Their Derivatives
Current Stage
Ref Project

Relations

Replaces
ASTM D5871-04 - Standard Specification for Benzene for Cyclohexane Feedstock
Effective Date
01-Oct-2006
Replaced By
ASTM D5871-07 - Standard Specification for Benzene for Cyclohexane Feedstock
Effective Date
01-Jun-2007
Referred By
ASTM D7011-15(2019) - Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective Detection
Effective Date
01-Oct-2006

Buy Standard

ASTM D5871-06 - Standard Specification for Benzene for Cyclohexane FeedstockASTM D5871-06 - Standard Specification for Benzene for Cyclohexane Feedstock
PreviousNext
Technical specification
ASTM D5871-06 - Standard Specification for Benzene for Cyclohexane Feedstock
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 5871 – 06
Standard Specification for
1
Benzene for Cyclohexane Feedstock
This standard is issued under the fixed designation D 5871; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 5713 Test Method for Analysis of High Purity Benzene
for Cyclohexane Feedstock by Capillary Gas Chromatog-
1.1 This specification covers benzene for cyclohexane feed-
raphy
stock.
D 6875 Test Method for Solidification Point of Industrial
1.2 The following applies to all specified limits in this
Organic Chemicals by Thermistor
standard: for purposes of determining conformance with this
D 7011 Test Method for Determination of Trace Thiophene
standard, an observed value or a calculated value shall be
in Refined Benzene by Gas Chromatography and Sulfur
rounded off “to the nearest unit” in the last right-hand digit
Selective Detection
used in expressing the specification limit, in accordance with
E29 Practice for Using Significant Digits in Test Data to
the rounding-off method of PracticeE29.
Determine Conformance with Specifications
1.3 Consult current OSHA regulations supplier’s Material
2.2 Other Document:
Safety Data Sheets for all materials used in this specification.
OSHA Regulations, 29 CFR, paragraphs 1910.1000 and
3
2. Referenced Documents
1910.1200
2
2.1 ASTM Standards:
3. Properties
D 848 Test Method for Acid Wash Color of Industrial
3.1 Benzene for Cyclohexane Feedstock shall conform to
Aromatic Hydrocarbons
the following requirements:
D 852 Test Method for Solidification Point of Benzene
A
Property Specification ASTM Test Method
D 1209 Test Method for Color of Clear Liquids (Platinum-
Cobalt Scale)
Benzene, min, weight % 99.90 D 5713 or D 4492
D 1685 TestMethodforTracesofThiopheneinBenzeneby Sulfur, max, mg/kg 1.0 D 5453
Thiophene, max, mg/kg 0.6 D 1685, D 4735 or
Spectrophotometry
D 7011
D 3437 Practice for Sampling and Handling Liquid Cyclic
Toluene plus methylcyclohexane max, 150 D 5713
Products mg/kg
Methylcyclopentane, max mg/kg 100 D 5713
D 4017 Test Method forWater in Paints and Paint Materials
N-hexane, max, mg/kg 80 D 5713
by Karl Fischer Method
Acid wash color, max pass with 1 D 848
B
D 4492 Test Method for Analysis of Benzene by Gas
Appearance .
Color, max, Pt-Co scale 10 D 1209 or D 5386
Chromatography
Water (if needed) D 4017
D 4735 Test Method for Determination of Trace Thiophene
Solidification point, anhydrous basis, 5.45 D 852 or D 6875
in Refined Benzene by Gas Chromatography min,° C
________________
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5871-19(Specification)
Standard Specification for Benzene for Cyclohexane Feedstock

ABSTRACT
This specification covers benzene for cyclohexane feedstock. Different tests shall be performed in order to determine the following properties of cyclohexane feedstock: benzene content, sulfur content, thiophene content, toluene plus methylcyclohexane content, methylcyclopentane content, N-hexane content, acid wash color, appearance, color, water content, and solidification point with anhydrous basis.
SCOPE
1.1 This specification covers benzene for cyclohexane feedstock.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 Consult current OSHA regulations supplier’s Safety Data Sheets for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E3274-21(Guide)
Standard Guide for Management of Investigation-Derived Waste Associated with PFAS

SIGNIFICANCE AND USE
4.1 Perfluoroalkyl and polyfluoroalkyl substances (PFAS) are a family of more than 4700 synthetic organic chemicals. PFAS can withstand high temperatures and survive highly corrosive environments. They are used in the manufacture of coatings, surface treatments, and specialty chemicals in cookware, carpets, food packaging, clothing, cosmetics, and other common consumer products. PFAS also have many industrial applications and are an active ingredient in certain types of fire-fighting foams (aqueous film-forming foams, or AFFF). PFAS coatings resist oil, grease, and water. PFAS are persistent compounds. Therefore, PFAS should be considered for purposes of managing investigation-derived waste where PFAS is known or suspected to be present in environmental media.  
4.1.1 PFAS are emerging contaminants for which environmental regulations and guidance are dynamic and are being developed simultaneously at federal, state, local, and international levels as more is learned about their characteristics, environmental fate, and management/treatment. Therefore, site-specific rules, regulations, and guidance should be evaluated for options and restrictions on management of PFAS  investigation-derived waste. For example, the Massachusetts Department of Environmental Protection has determined that PFAS wastes are “hazardous materials” subject to the Massachusetts Oil and Hazardous Material Release Prevention and Response Act (M.G.L. Chapter 21E) and the Massachusetts Contingency Plan. Other states and jurisdictions may have or will develop and implement similar determinations that affect the on-site management, storage, and labeling and off-site transportation requirements for PFAS  investigation-derived waste.  
4.1.2 Given the characteristics and persistence of PFAS compounds, PFAS  investigation-derived waste presents special handling and treatment/disposal considerations. EPA recently issued Interim Guidance on the Destruction and Disposal of Perfluoralkyl and Polyfluoralky...
SCOPE
1.1 Existing guidance on the management of investigation-derived waste is focused upon cuttings, purge water, personal protective equipment, and other miscellaneous solid waste generated at property that may be impacted by the release of hazardous materials and hazardous substances. These hazardous substances include, but are not limited to, heavy metals, petroleum, petroleum byproducts, solvents, polycyclic aromatic hydrocarbons, organic and inorganic corrosives, radioactive material, and explosives. Guidance on the management of investigation derived waste generated at sites that may be impacted by releases of perfluoroalkyl and polyfluoroalkyl substances (PFAS) is limited. This standard guide addresses this deficiency  
1.2 This guide describes best practices for managing investigation-derived waste associated with PFAS that are consistent with federal and state policies and regulations at the date of issuance. The user is advised to determine if new regulations or rules have been promulgated by the state, federal, or tribal regulatory agency having jurisdiction over the property.  
1.3 This guide describes considerations to prevent the unintended and unauthorized disposal of liquid investigation-derived waste that may contain PFAS into wastewater treatment plants or systems that are not permitted to receive these waste streams.  
1.4 This guide describes considerations to prevent the unintended and unauthorized disposal of solid investigation-derived waste that may contain PFAS into landfills or other solid waste disposal facilities that are not permitted to receive these waste streams.  
1.5 This guide describes several stormwater pollution prevention best management practices applicable to investigation-derived waste.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety,...

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5871-19(Specification)
Standard Specification for Benzene for Cyclohexane Feedstock

ABSTRACT
This specification covers benzene for cyclohexane feedstock. Different tests shall be performed in order to determine the following properties of cyclohexane feedstock: benzene content, sulfur content, thiophene content, toluene plus methylcyclohexane content, methylcyclopentane content, N-hexane content, acid wash color, appearance, color, water content, and solidification point with anhydrous basis.
SCOPE
1.1 This specification covers benzene for cyclohexane feedstock.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 Consult current OSHA regulations supplier’s Safety Data Sheets for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off