ASTM F1483-23

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1483 − 23 An American National Standard
Standard Specification for
1
Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe
This standard is issued under the fixed designation F1483; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D883 Terminology Relating to Plastics
D1598 Test Method for Time-to-Failure of Plastic Pipe
1.1 This specification covers requirements for materials,
Under Constant Internal Pressure
dimensions, sustained pressure, accelerated regression testing,
D1599 Test Method for Resistance to Short-Time Hydraulic
burst pressure, flattening, impact resistance, workmanship,
Pressure of Plastic Pipe, Tubing, and Fittings
solvent cement joint testing, and methods of marking for
D1600 Terminology for Abbreviated Terms Relating to Plas-
oriented poly(vinyl chloride) (PVCO) pipe for pressure appli-
tics
cations.
D1784 Classification System and Basis for Specification for
1.2 The PVCO pipe shall be joined using either elastomeric
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
seals (gaskets) or solvent cement with primer. The gasketed
rinated Poly(Vinyl Chloride) (CPVC) Compounds
joint shall meet the requirements of Specification D3139 and
D2122 Test Method for Determining Dimensions of Ther-
the elastomeric seal shall meet the requirements of Specifica-
moplastic Pipe and Fittings
tion F477. The solvent cemented joint shall meet the require-
D2152 Test Method for Adequacy of Fusion of Extruded
ments of 5.3.3.
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
1.3 The values stated in inch-pound units are to be regarded Acetone Immersion
D2241 Specification for Poly(Vinyl Chloride) (PVC)
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only Pressure-Rated Pipe (SDR Series)
D2444 Practice for Determination of the Impact Resistance
and are not considered standard.
of Thermoplastic Pipe and Fittings by Means of a Tup
1.4 The following safety hazards caveat pertains only to the
(Falling Weight)
test method portion, Section 7 of this specification: This
D2564 Specification for Solvent Cements for Poly(Vinyl
standard does not purport to address all of the safety concerns,
Chloride) (PVC) Plastic Piping Systems
if any, associated with its use. It is the responsibility of the user
D2837 Test Method for Obtaining Hydrostatic Design Basis
of this standard to establish appropriate safety, health, and
for Thermoplastic Pipe Materials or Pressure Design Basis
environmental practices and determine the applicability of
for Thermoplastic Pipe Products
regulatory limitations prior to use.
D2855 Practice for the Two-Step (Primer and Solvent Ce-
1.5 This international standard was developed in accor-
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
dance with internationally recognized principles on standard-
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
ization established in the Decision on Principles for the
Piping Components with Tapered Sockets
Development of International Standards, Guides and Recom-
D3139 Specification for Joints for Plastic Pressure Pipes
mendations issued by the World Trade Organization Technical
Using Flexible Elastomeric Seals
Barriers to Trade (TBT) Committee.
F412 Terminology Relating to Plastic Piping Systems
2. Referenced Documents
F477 Specification for Elastomeric Seals (Gaskets) for Join-
2
ing Plastic Pipe
2.1 ASTM Standards:
F656 Specification for Primers for Use in Solvent Cement
D618 Practice for Conditioning Plastics for Testing
Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and
Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
3
2.2 Federal Standard:
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl
Based Pipe.
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
Current edition approved Feb. 15, 2023. Published March 2023. Originally
3
2.3 Military Standard:
approved in 1993. Last previous edition approved in 2017 as F1483 –17. DOI:
MIL-STD-129 Marking for Shipment and Storage
10.1520/F1483-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from DLA Document Services Building 4/D 700 Robbins Avenue
the ASTM website. Philadelphia, PA 19111-5094 http://quick
...