Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)

SCOPE
1.1 This specification covers fuel blend grades of 6 volume percent to 20 volume percent (%) biodiesel with the remainder being a light middle or middle distillate diesel fuel, collectively designated as B6 to B20. These grades are suitable for various types of diesel engines.  
1.1.1 The biodiesel component of the blend shall conform to the requirements of Specification D6751. The remainder of the fuel shall be a light middle or middle distillate grade diesel fuel conforming to Specification D975 grades No. 1-D and No. 2-D of any sulfur level specified with the following exceptions. The light middle or middle distillate grade diesel fuel whose sulfur level, aromatic level, cetane, or lubricity falls outside of Specification D975 may be blended with biodiesel meeting Specification D6751, provided the finished mixtures meets this specification.  
1.1.2 The fuel sulfur grades are described as follows:
1.1.2.1 Grade B6 to B20 S15—A fuel with a maximum of 15 ppm sulfur.
1.1.2.2 Grade B6 to B20 S500—A fuel with a maximum of 500 ppm sulfur.
1.1.2.3 Grade B6 to B20 S5000—A fuel with a maximum of 5000 ppm sulfur.  
1.2 This specification prescribes the required properties of B6 to B20 biodiesel blends at the time and place of delivery. The specification requirements may be applied at other points in the production and distribution system when provided by agreement between the purchaser and the supplier.  
1.2.1 Nothing in this specification shall preclude observance of federal, state, or local regulations that may be more restrictive.
Note 1: The generation and dissipation of static electricity can create problems in the handling of distillate diesel fuel oils. For more information on this subject, see Guide D4865.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

General Information

Status
Historical
Publication Date
31-Dec-2016
Current Stage
Ref Project

Relations

Effective Date
01-Jan-2017

Buy Standard

Technical specification
ASTM D7467-17 - Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
English language
21 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D7467-17 - Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
English language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D7467 −17
Standard Specification for
1
Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
This standard is issued under the fixed designation D7467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.3 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
1.1 This specification covers fuel blend grades of 6 volume
standard.
percent to 20 volume percent (%) biodiesel with the remainder
beingalightmiddleormiddledistillatedieselfuel,collectively
2. Referenced Documents
designated as B6 to B20. These grades are suitable for various 2
2.1 ASTM Standards:
types of diesel engines.
D56Test Method for Flash Point by Tag Closed Cup Tester
1.1.1 Thebiodieselcomponentoftheblendshallconformto
D86Test Method for Distillation of Petroleum Products and
therequirementsofSpecificationD6751.Theremainderofthe
Liquid Fuels at Atmospheric Pressure
fuelshallbealightmiddleormiddledistillategradedieselfuel
D93Test Methods for Flash Point by Pensky-Martens
conformingtoSpecificationD975gradesNo.1-DandNo.2-D
Closed Cup Tester
ofanysulfurlevelspecifiedwiththefollowingexceptions.The
D129Test Method for Sulfur in Petroleum Products (Gen-
light middle or middle distillate grade diesel fuel whose sulfur
eral High Pressure Decomposition Device Method)
level, aromatic level, cetane, or lubricity falls outside of
D130Test Method for Corrosiveness to Copper from Petro-
Specification D975 may be blended with biodiesel meeting
leum Products by Copper Strip Test
SpecificationD6751,providedthefinishedmixturesmeetsthis
D445Test Method for Kinematic Viscosity of Transparent
specification.
and Opaque Liquids (and Calculation of DynamicViscos-
1.1.2 The fuel sulfur grades are described as follows:
ity)
1.1.2.1 Grade B6 to B20 S15—A fuel with a maximum of D482Test Method for Ash from Petroleum Products
D524Test Method for Ramsbottom Carbon Residue of
15ppm sulfur.
Petroleum Products
1.1.2.2 Grade B6 to B20 S500—Afuel with a maximum of
D613Test Method for Cetane Number of Diesel Fuel Oil
500ppm sulfur.
D664Test Method for Acid Number of Petroleum Products
1.1.2.3 Grade B6 to B20 S5000—Afuelwithamaximumof
by Potentiometric Titration
5000ppm sulfur.
D975Specification for Diesel Fuel Oils
1.2 This specification prescribes the required properties of
D976Test Method for Calculated Cetane Index of Distillate
B6 to B20 biodiesel blends at the time and place of delivery.
Fuels
The specification requirements may be applied at other points
D1266TestMethodforSulfurinPetroleumProducts(Lamp
in the production and distribution system when provided by
Method)
agreement between the purchaser and the supplier.
D1319Test Method for HydrocarbonTypes in Liquid Petro-
leum Products by Fluorescent Indicator Adsorption
1.2.1 Nothinginthisspecificationshallprecludeobservance
D1552Test Method for Sulfur in Petroleum Products by
of federal, state, or local regulations that may be more
High Temperature Combustion and Infrared (IR) Detec-
restrictive.
tion or Thermal Conductivity Detection (TCD)
NOTE 1—The generation and dissipation of static electricity can create
D2500Test Method for Cloud Point of Petroleum Products
problems in the handling of distillate diesel fuel oils. For more informa-
and Liquid Fuels
tion on this subject, see Guide D4865.
D2622Test Method for Sulfur in Petroleum Products by
Wavelength Dispersive X-ray Fluorescence Spectrometry
D2624Test Methods for Electrical Conductivity ofAviation
1
This specification is under the jurisdiction of ASTM Committee D02 on
and Distillate Fuels
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Subcommittee D02.E0 on Burner, Diesel, Non-Aviation Gas Turbine, and Marine
2
Fuels. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 1, 2017. Published March 2017. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
ɛ1
approved in 2008. Last previous edition approved in 2015 as D7467–15c . DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D7467-17. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7467−17
D2709Test Method for Water and Sediment in Middle D7371Test Method for Determination of Biodiesel (Fatty
Distillate Fuels by Centrifuge AcidMethylEsters)ContentinDieselFuelOilUsingMid
D2880Specification
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7467 − 15c D7467 − 17
Standard Specification for
1
Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
This standard is issued under the fixed designation D7467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Footnote J of Table 1 was corrected editorially in February 2016.
1. Scope*
1.1 This specification covers fuel blend grades of 6 volume percent to 20 volume percent (%) biodiesel with the remainder being
a light middle or middle distillate diesel fuel, collectively designated as B6 to B20. These grades are suitable for various types of
diesel engines.
1.1.1 The biodiesel component of the blend shall conform to the requirements of Specification D6751. The remainder of the fuel
shall be a light middle or middle distillate grade diesel fuel conforming to Specification D975 grades No. 1-D and No. 2-D of any
sulfur level specified with the following exceptions. The light middle or middle distillate grade diesel fuel whose sulfur level,
aromatic level, cetane, or lubricity falls outside of Specification D975 may be blended with biodiesel meeting Specification D6751,
provided the finished mixtures meets this specification.
1.1.2 The fuel sulfur grades are described as follows:
1.1.2.1 Grade B6 to B20 S15—A fuel with a maximum of 15 ppm sulfur.
1.1.2.2 Grade B6 to B20 S500—A fuel with a maximum of 500 ppm sulfur.
1.1.2.3 Grade B6 to B20 S5000—A fuel with a maximum of 5000 ppm sulfur.
1.2 This specification prescribes the required properties of B6 to B20 biodiesel blends at the time and place of delivery. The
specification requirements may be applied at other points in the production and distribution system when provided by agreement
between the purchaser and the supplier.
1.2.1 Nothing in this specification shall preclude observance of federal, state, or local regulations that may be more restrictive.
NOTE 1—The generation and dissipation of static electricity can create problems in the handling of distillate diesel fuel oils. For more information on
this subject, see Guide D4865.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D56 Test Method for Flash Point by Tag Closed Cup Tester
D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method)
D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D482 Test Method for Ash from Petroleum Products
D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products
D613 Test Method for Cetane Number of Diesel Fuel Oil
D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration
D975 Specification for Diesel Fuel Oils
D976 Test Method for Calculated Cetane Index of Distillate Fuels
D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)
1
This specification is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.E0 on Burner, Diesel, Non-Aviation Gas Turbine, and Marine Fuels.
Current edition approved Oct. 1, 2015Jan. 1, 2017. Published November 2015March 2017. Originally approved in 2008. Last previous edition approved in 2015 as
ɛ1
D7467 – 15b.D7467 – 15c . DOI: 10.1520/D7467-15CE01.10.1520/D7467-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7467 − 17
D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
D1552 Test Method for Sulfur in Petroleum Products by High Temperature Combustion and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.