ASTM C1797-23a
(Specification)Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete
Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete
ABSTRACT
This specification covers ground calcium carbonate (GCC, a type of ground limestone) and other finely divided aggregate mineral filler (AMF) materials for use in concrete mixtures. It defines the types of GCC and AMF materials for use in concrete. If concrete in service is subject to sulfate exposure, fillers derived from ground limestone should not be used unless mitigation methods are used.
SIGNIFICANCE AND USE
A1.3 Significance and Use
A1.3.1 This test method provides analytical procedures to determine the major chemical constituents of limestone (see Note 1). The percentages of specific constituents that determine a material’s quality or fitness for use are of significance depending upon the purpose or end use of the material. Results obtained may be used in relation to specification requirements.
Note A1.1: This test method can be applied to other calcareous materials if provisions are made to compensate for known interferences.
SCOPE
1.1 This specification applies to ground calcium carbonate (GCC is a type of ground limestone) and other finely divided aggregate mineral filler (AMF) materials for use in concrete mixtures. The specification defines the types of GCC and AMF materials for use in concrete.
1.2 If concrete in service is subject to sulfate exposure, fillers derived from ground limestone should not be used unless mitigation methods are used.
Note 1: American Concrete Institute (ACI) technical documents 201.2R, 318, 332, and 350 contain useful information and code requirements dealing with sulfate exposure in service. Soluble sulfate in water can be determined in accordance with Test Method D516 or Test Method D4130. Percent sulfate by mass in soil can be determined by Test Method C1580.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 2: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.
1.4 The text of this standard references notes and footnotes, which provide explanatory information. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1797 − 23a
Standard Specification for
Ground Calcium Carbonate and Aggregate Mineral Fillers
1
for use in Hydraulic Cement Concrete
This standard is issued under the fixed designation C1797; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification applies to ground calcium carbonate 2.1 ASTM Standards:
(GCC is a type of ground limestone) and other finely divided C25 Test Methods for Chemical Analysis of Limestone,
aggregate mineral filler (AMF) materials for use in concrete Quicklime, and Hydrated Lime
mixtures. The specification defines the types of GCC and AMF C50/C50M Practice for Sampling, Sample Preparation,
materials for use in concrete. Packaging, and Marking of Lime and Limestone Products
C51 Terminology Relating to Lime and Limestone (as Used
1.2 If concrete in service is subject to sulfate exposure,
by the Industry)
fillers derived from ground limestone should not be used unless
C110 Test Methods for Physical Testing of Quicklime,
mitigation methods are used.
Hydrated Lime, and Limestone
NOTE 1—American Concrete Institute (ACI) technical documents
C117 Test Method for Materials Finer than 75-μm (No. 200)
201.2R, 318, 332, and 350 contain useful information and code require-
ments dealing with sulfate exposure in service. Soluble sulfate in water
Sieve in Mineral Aggregates by Washing
can be determined in accordance with Test Method D516 or Test Method
C125 Terminology Relating to Concrete and Concrete Ag-
D4130. Percent sulfate by mass in soil can be determined by Test Method
gregates
C1580.
C136/C136M Test Method for Sieve Analysis of Fine and
1.3 The values stated in SI units are to be regarded as
Coarse Aggregates
standard. No other units of measurement are included in this
C311/C311M Test Methods for Sampling and Testing Fly
standard.
Ash or Natural Pozzolans for Use in Portland-Cement
NOTE 2—Sieve size is identified by its standard designation in Speci-
Concrete
fication E11. The alternative designation given in parentheses is for
C511 Specification for Mixing Rooms, Moist Cabinets,
information only and does not represent a different standard sieve size.
Moist Rooms, and Water Storage Tanks Used in the
1.4 The text of this standard references notes and footnotes,
Testing of Hydraulic Cements and Concretes
which provide explanatory information. These notes and foot-
C566 Test Method for Total Evaporable Moisture Content of
notes (excluding those in tables and figures) shall not be
Aggregate by Drying
considered as requirements of the standard.
C1580 Test Method for Water-Soluble Sulfate in Soil
1.5 This standard does not purport to address all of the
C1777 Test Method for Rapid Determination of the Methyl-
safety concerns, if any, associated with its use. It is the
ene Blue Value for Fine Aggregate or Mineral Filler Using
responsibility of the user of this standard to establish appro-
a Colorimeter
priate safety and health practices and determine the applica-
D75/D75M Practice for Sampling Aggregates
bility of regulatory limitations prior to use.
D516 Test Method for Sulfate Ion in Water
1.6 This international standard was developed in accor-
D1193 Specification for Reagent Water
dance with internationally recognized principles on standard-
D4130 Test Method for Sulfate Ion in Brackish Water,
ization established in the Decision on Principles for the
Seawater, and Brines
Development of International Standards, Guides and Recom-
E11 Specification for Woven Wire Test Sieve Cloth and Test
mendations issued by the World Trade Organization Technical
Sieves
Barriers to Trade (TBT) Committee.
E350 Test Methods for Chemical Analysis of Carbon Steel,
Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and
Wrought Iron
1
This specification is under the jurisdiction of ASTM Committee C09 on
Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee
2
C09.20 on Aggregates. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2023. Published December 2023. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2016. Last previous edition approved in 2023 as C1797–23. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1797-23A. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Internati
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1797 − 23 C1797 − 23a
Standard Specification for
Ground Calcium Carbonate and Aggregate Mineral Fillers
1
for use in Hydraulic Cement Concrete
This standard is issued under the fixed designation C1797; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification applies to ground calcium carbonate (GCC is a type of ground limestone) and other finely divided aggregate
mineral filler (AMF) materials for use in concrete mixtures. The specification defines the types of GCC and AMF materials for
use in concrete.
1.2 If concrete in service is subject to sulfate exposure, fillers derived from ground limestone should not be used unless mitigation
methods are used.
NOTE 1—American Concrete Institute (ACI) technical documents 201.2R, 318, 332, and 350 contain useful information and code requirements dealing
with sulfate exposure in service. Soluble sulfate in water can be determined in accordance with Test Method D516 or Test Method D4130. Percent sulfate
by mass in soil can be determined by Test Method C1580.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
NOTE 2—Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only
and does not represent a different standard sieve size.
1.4 The text of this standard references notes and footnotes, which provide explanatory information. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime
C50/C50M Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products
1
This specification is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.20 on
Aggregates.
Current edition approved Aug. 15, 2023Dec. 1, 2023. Published August 2023December 2023. Originally approved in 2016. Last previous edition approved in 20172023
as C1797–17. DOI: 10.1520/C1797-23.–23. DOI: 10.1520/C1797-23A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1797 − 23a
C51 Terminology Relating to Lime and Limestone (as Used by the Industry)
C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
C125 Terminology Relating to Concrete and Concrete Aggregates
C136/C136M Test Method for Sieve Analysis of Fine and Coarse Aggregates
C311/C311M Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic
Cements and Concretes
C566 Test Method for Total Evaporable Moisture Content of Aggregate by Drying
C595/C595M Specification for Blended Hydraulic Cements
C1580 Test Method for Water-Soluble Sulfate in Soil
C1777 Test Method for Rapid Determination of the Methylene Blue Value for Fine Aggregate or Mineral Filler Using a
Colorimeter
D75/D
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.