ASTM C1071-12
(Specification)Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)
Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)
ABSTRACT
This specification covers fibrous glass insulation used as a thermal and sound absorbing liner for interior surfaces of ducts, plenums, and other air handling equipment. The insulation shall be of the following types: Type I and Type II. The basic material shall be made from glass processed from the molten state into fibrous form with a binder added to form dimensionally stable insulation. The following test methods shall be performed: corrosiveness; water vapor sorption; fungi resistance; temperature resistance; erosion resistance; odor emission; surface burning characteristics; apparent thermal conductivity; sound absorption coefficients; bacteria resistance; and combustion characteristics.
SCOPE
1.1 This specification covers fibrous glass insulation used as a thermal and sound absorbing liner for interior surfaces of ducts, plenums, and other air handling equipment that handle air up to 250°F (121°C).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1071 −12
StandardSpecification for
Fibrous Glass Duct Lining Insulation (Thermal and Sound
1
Absorbing Material)
This standard is issued under the fixed designation C1071; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C665 Specification for Mineral-Fiber Blanket Thermal Insu-
lation for Light Frame Construction and Manufactured
1.1 This specification covers fibrous glass insulation used as
Housing
a thermal and sound absorbing liner for interior surfaces of
C1104/C1104M Test Method for Determining the Water
ducts, plenums, and other air handling equipment that handle
Vapor Sorption of Unfaced Mineral Fiber Insulation
air up to 250°F (121°C).
C1114 Test Method for Steady-State Thermal Transmission
1.2 The values stated in inch-pound units are to be regarded
Properties by Means of the Thin-Heater Apparatus
as standard. The values given in parentheses are mathematical
C1304 Test Method for Assessing the Odor Emission of
conversions to SI units that are provided for information only
Thermal Insulation Materials
and are not considered standard.
C1338 Test Method for Determining Fungi Resistance of
1.3 This standard does not purport to address all of the
Insulation Materials and Facings
safety concerns, if any, associated with its use. It is the E84 Test Method for Surface Burning Characteristics of
responsibility of the user of this standard to establish appro-
Building Materials
priate safety and health practices and determine the applica- E795 Practices for Mounting Test Specimens During Sound
bility of regulatory limitations prior to use.
Absorption Tests
E2231 Practice for Specimen Preparation and Mounting of
2. Referenced Documents
Pipe and Duct Insulation Materials to Assess Surface
2
Burning Characteristics
2.1 ASTM Standards:
C167 Test Methods for Thickness and Density of Blanket or G21 Practice for Determining Resistance of Synthetic Poly-
meric Materials to Fungi
Batt Thermal Insulations
G22 Practice for Determining Resistance of Plastics to
C168 Terminology Relating to Thermal Insulation
3
Bacteria (Withdrawn 2002)
C177 Test Method for Steady-State Heat Flux Measure-
ments and Thermal Transmission Properties by Means of
2.2 Other Standards:
the Guarded-Hot-Plate Apparatus
CAN/ULC-S102 Method of Test for Surface Burning Char-
4
C390 Practice for Sampling and Acceptance of Thermal
acteristics of Building Materials and Assemblies
5
Insulation Lots
NAIMA Fibrous Glass Duct Liner Standard
C411 Test Method for Hot-Surface Performance of High-
NFPA 259 Test Method for Potential Heat of Building
6
Temperature Thermal Insulation
Materials
7
C423 Test Method for SoundAbsorption and SoundAbsorp-
SMACNA HVAC Duct Construction Standards
4
tion Coefficients by the Reverberation Room Method
UL 181 Factory-Made Air Ducts and Air Connectors
C518 Test Method for Steady-State Thermal Transmission
Properties by Means of the Heat Flow Meter Apparatus
3
The last approved version of this historical standard is referenced on
www.astm.org.
1 4
This specification is under the jurisdiction of ASTM Committee C16 on Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas,
Thermal Insulation and is the direct responsibility of Subcommittee C16.23 on WA 98607-8542, http://www.ul.com.
5
Blanket and Loose Fill Insulation. Available from North American Insulation Manufacturers Association
Current edition approved March 1, 2012. Published March 2012. Originally (NAIMA), 44 Canal Center Plaza, Suite 310, Alexandria, VA 22314, http://
ε1
approved in 1986. Last previous edition approved in 2005 as C1071 – 05 . DOI: www.naima.org.
6
10.1520/C1071-12. Available from National Fire Protection Association (NFPA), 1 Batterymarch
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Park, Quincy, MA 02169-7471, http://www.nfpa.org.
7
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Sheet Metal and Air Conditioning Contractors’ National
Standards volume information, refer to the standard’s Document Summary page on Association 4201 Lafayette Center Drive Chantilly, Virginia 20151-1219, http://
the ASTM website. www.smacna.org
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1071 − 12
UL723 Test for Surface Burning Characteristics of Building or show evidence of delamination or continued erosion when
4
Materials air is passed through typ
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:C1071–05 Designation: C1071 – 12
Standard Specification for
Fibrous Glass Duct Lining Insulation (Thermal and Sound
1
Absorbing Material)
This standard is issued under the fixed designation C1071; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Sections 2.2 and 12.9 were editorially updated in June 2008.
1. Scope
1.1 This specification covers fibrous glass insulation used as a thermal and sound absorbing liner for interior surfaces of ducts,
plenums, and other air handling equipment that handle air up to 250°F (121°C).
1.2The values stated in inch-pound units are the standard. The SI values in parentheses are for information only.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C167 Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C665 Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C1104/C1104M Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
C1114 Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
C1304 Test Method for Assessing the Odor Emission of Thermal Insulation Materials
C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings
E84 Test Method for Surface Burning Characteristics of Building Materials
E795 Practices for Mounting Test Specimens During Sound Absorption Tests
E2231 Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning
Characteristics
G21 Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
G22 Practice for Determining Resistance of Plastics to Bacteria
2.2 Other Standards: NAIMA Fibrous Glass Duct Liner Standard
1
ThisspecificationisunderthejurisdictionofASTMCommitteeC16onThermalInsulationandisthedirectresponsibilityofSubcommitteeC16.23onBlanketandLoose
Fill Insulation.
Current edition approved April 1, 2005. Published April 2005. Originally approved in 1986. Last previous edition approved in 2000 as C1071–00. DOI:
10.1520/C1071-05E01.
´1
Current edition approved March 1, 2012. Published March 2012. Originally approved in 1986. Last previous edition approved in 2005 as C1071 – 05 . DOI:
10.1520/C1071-12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1071 – 12
3
CAN/ULC-S102 Method ofTest for Surface Burning Characteristics of Building Materials andAssemblies SMACNAHVAC
Duct Construction Standards
4
NAIMA Fibrous Glass Duct Liner Standard UL 723 Test for Surface Burning Characteristics of Building Materials
5
NFPA259 Test Method for Potential Heat of Building Materials NFPA255 Method of Test of Surface Burning Characteristics
of Building Materials
6 6
SMACNA HVAC Duct Construction Standards NFPA 259 Test Method for P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.