CEN/TC 216/WG 2 - Veterinary use

This procedure specifies a test method and the minimum requirements for bactericidal activity of teat disinfectants that form a homogeneous, physically stable preparation when diluted with hard water - or in the case of ready-to-use products - with water.
This method applies to teat disinfectants that are used in the veterinary area on teat skin without mechanical action as pre-milking and/or post-milking teat disinfectants.
NOTE 1 The method described is intended to determine the activity of commercial formulations under the conditions in which they are used.
NOTE 2 This method corresponds to a phase 2 step 2 test.
NOTE 3 Two types of synthetic skin were assessed in a ring trial with no significant difference in performance. Other synthetic skins may become available and may be used if it can be shown that they give comparable results to the two referenced in this standard.

This European Standard specifies a test method and the minimum requirements for virucidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation when diluted with hard water, or - in the case of ready-to-use-products - with water.
This European Standard applies to products that are used in the veterinary area on non-porous surfaces without mechanical action i.e. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.
NOTE 3   Using this European Standard, it is possible to determine the virucidal activity of the undiluted product.
NOTE 4   This standard uses Porcine Parvovirus because Bovine Enterovirus Type 1 (ECBO) virus used in the suspension test EN 14675 cannot be used for surface testing because of its loss of titre during drying. Porcine
Parvovirus has comparable resistance to ECBO virus.

This document specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use products - with water. Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used. This document applies to products that are used for equipment disinfection by immersion, surface disinfection by wiping, spraying, flooding or other means and teat disinfection in the veterinary area - e.g. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry into processing industry. This document also applies to products used for teat disinfection in these veterinary areas.
This method is not applicable to evaluate the activity of hand hygiene products. For these products reference is made to EN 14885, which specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE   This method corresponds to a phase 2 step 1 test.

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectants and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water - or in the case of ready-to-use products - with water.
This European Standard applies to products that are used in the veterinary area on porous surfaces without mechanical action i.e. in the breeding, husbandry, production, !veterinary care facilities", transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to “use recommendations”.
NOTE 1 The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2 This method corresponds to a phase 2 step 2 test.
NOTE 3 This method cannot be used to evaluate the activity of products against mycobacteria or bacterial spores.

This European Standard specifies a test method and the minimum requirements for fungicidal or yeasticidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water. Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
This European Standard applies to products that are used in the veterinary area - i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1 The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2 This method corresponds to a phase 2 step 1 test (Annex F).

This European Standard specifies a test method and the minimum requirements for virucidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water. Products can only be tested at a concentration of 80 % or less as some dilution is always produced by adding the test organisms and interfering substance.
This European Standard applies to products that are used in the veterinary area, i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
NOTE 1   The method described is intended to determine the virucidal activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 1.

This European Standard specifies a test method and the minimum requirements for fungicidal or yeasticidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation in hard water or in the case of ready-to-use products with water.
This European Standard applies to products for use in the veterinary area i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to use recommendations.
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.

This European Standard specifies a test method and the minimum requirements for mycobactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water.
Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
This European Standard applies to products that are used in the veterinary area - i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 1 test.

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation when diluted with hard water, or - in the case of ready-to-use-products - with water.
This European Standard applies to products that are used in the veterinary area on non-porous surfaces without mechanical action i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.
NOTE 3   This method cannot be used to evaluate the activity of products against mycobacteria.

This document specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use products - with water. Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used. This document applies to products that are used for equipment disinfection by immersion, surface disinfection by wiping, spraying, flooding or other means and teat disinfection in the veterinary area - e.g. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry into processing industry. This document also applies to products used for teat disinfection in these veterinary areas.
This method is not applicable to evaluate the activity of hand hygiene products. For these products reference is made to EN 14885, which specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE This method corresponds to a phase 2 step 1 test.

This document specifies a test method and the minimum requirements for bactericidal activity of teat disinfectants that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use products - with water.
This method applies to teat disinfectants that are used on teat skin without mechanical action as pre-milking and/or post-milking teat disinfectants in the veterinary area, e.g. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry into processing industry.
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 2 test.

This document specifies a test method and the minimum requirements for mycobactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water.
Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
This document is applicable to products that are used for equipment disinfection by immersion, surface disinfection by wiping, spraying or flooding or other means and teat disinfection in the veterinary area - i.e. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE   This method corresponds to a phase 2 step 1 test.

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation when diluted with hard water, or - in the case of ready-to-use-products - with water.
This European Standard applies to products that are used in the veterinary area on non-porous surfaces without mechanical action i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.
NOTE 3   This method cannot be used to evaluate the activity of products against mycobacteria.

This European Standard specifies a test method and the minimum requirements for virucidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation when diluted with hard water, or - in the case of ready-to-use-products - with water.
This European Standard applies to products that are used in the veterinary area on non-porous surfaces without mechanical action i.e. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.
NOTE 3   Using this European Standard, it is possible to determine the virucidal activity of the undiluted product.
NOTE 4   This standard uses Porcine Parvovirus because Bovine Enterovirus Type 1 (ECBO) virus used in the suspension test EN 14675 cannot be used for surface testing because of its loss of titre during drying. Porcine
Parvovirus has comparable resistance to ECBO virus.

This document specifies a test method and the minimum requirements for fungicidal or yeasticidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water. Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
This document applies to products that are used in the veterinary area - i.e. in the breeding, husbandry, production, veterinary care facilities, transport and disposal of all animals except when in the food chain following death and entry into processing industry. This document also applies to products used for teat disinfection.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 1 test.

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectants and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water - or in the case of ready-to-use products - with water.
This European Standard applies to products that are used in the veterinary area on porous surfaces without mechanical action i.e. in the breeding, husbandry, production, transport, veterinary care facilities and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to use recommendations.
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 2 test.
NOTE 3    This method cannot be used to evaluate the activity of products against mycobacteria or bacterial spores.

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectants and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water - or in the case of ready-to-use products - with water.
This European Standard applies to products that are used in the veterinary area on porous surfaces without mechanical action i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to use recommendations.
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 2 test.
NOTE 3    This method cannot be used to evaluate the activity of products against mycobacteria or bacterial spores.

TC - Correction of ATCC number for Escherichia coli in Annex A b) - Healthcare

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use products - with water. Products can only be tested at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and interfering substance.
This European Standard applies to products that are used in the veterinary area - e.g. in the breeding, husbandry, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to 'use recommendations'.
NOTE 1   The method described is intended to determine the activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 1 test.

This European Standard specifies a test method and the minimum requirements for virucidal activity of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when diluted with hard water or - in the case of ready-to-use-products - with water. Products can only be tested at a concentration of 80 % or less as some dilution is always produced by adding the test organisms and interfering substance.
This European Standard applies to products that are used in the veterinary field i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
NOTE 1   The method described is intended to determine the virucidal activity of commercial formulations or active substances under the conditions in which they are used.
NOTE 2   This method corresponds to a phase 2 step 1 test (Annex E).

This European Standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation when diluted with hard water or in the case of ready-to-use-products with water.
This European Standard is applicable to products for use in the veterinary area i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations".
NOTE 1   Mycobacteria are the subject of a separate standard.
NOTE 2   This method corresponds to a Phase 2 Step 2 test.

This European Standard specifies a test method and the minimum requirements for mycobactericidal activity
of chemical disinfectant and antiseptic products that form a homogeneous, physically stable preparation when
diluted with hard water or in the case of ready-to-use-products with water. Products can only be tested
at a concentration of 80 % or less, as some dilution is always produced by adding the test organisms and
interfering substance.
This European Standard applies to products that are used in the veterinary area i.e. in the breeding,
husbandry, production, transport and disposal of all animals except when in the food chain following death
and entry to the processing industry.
NOTE 1 The method described is intended to determine the activity of commercial formulations or active substances
under the conditions in which they are used.
NOTE 2 This method corresponds to a phase 2 step 1 test (Annex F).

This European standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form an homogenous physically stable preparation in standardised hard water. This European Standard is applicable to products for use in the veterinary field i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.

This document specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form a homogeneous physically stable preparation in hard water or - in the case of ready-to-use - with water.
This document is applicable to products for use in the veterinary field i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.
NOTE 1   Mycobacteria are the subject of a separate standard.
NOTE 2   This method corresponds to a Phase 2 Step 2 test (Annex E).

This European standard specifies a test method and the minimum requirements for bactericidal activity of chemical disinfectant and antiseptic products that form an homogenous physically stable preparation in standardised hard water. This European Standard is applicable to products for use in the veterinary field i.e. in the breeding, husbandry, production, transport and disposal of all animals except when in the food chain following death and entry to the processing industry.