SIST EN IEC 62841-3-5:2022

SLOVENSKI STANDARD
SIST EN IEC 62841-3-5:2022
01-september-2022
Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost
- 3-5. del: Posebne zahteve za prenosne tračne žage
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-5: Particular requirements for transportable band saws
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-5: Exigences particulières pour les scies à ruban portables
Ta slovenski standard je istoveten z: EN IEC 62841-3-5:2022
ICS:
25.100.40 Žagni listi Saws
25.140.20 Električna orodja Electric tools
SIST EN IEC 62841-3-5:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62841-3-5:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 62841-3-5:2022


EUROPEAN STANDARD EN IEC 62841-3-5

NORME EUROPÉENNE

EUROPÄISCHE NORM July 2022
ICS 25.140.20

English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-5: Particular
requirements for transportable band saws
(IEC 62841-3-5:2022)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-5: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à ruban portables Gartenmaschinen - Sicherheit - Teil 3-5: Besondere
(IEC 62841-3-5:2022) Anforderungen für transportable Bandsägen
(IEC 62841-3-5:2022)
This European Standard was approved by CENELEC on 2022-06-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62841-3-5:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62841-3-5:2022
EN IEC 62841-3-5:2022 (E)
European foreword
The text of document 116/574/FDIS, future edition 1 of IEC 62841-3-5, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-3-5:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-04-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-04-18
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN 62841-1:2015.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential
requirements of EU Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an
integral part of EN IEC 62841-3-5:2022/A11:2022.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62841-3-5:2022 was approved by CENELEC as a
European Standard without any modification.

2

---------------------- Page: 4 ----------------------
SIST EN IEC 62841-3-5:2022
IEC 62841-3-5
®

Edition 1.0 2022-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-5: Particular requirements for transportable band saws
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 3-5: Exigences particulières pour les scies à ruban transportables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-5395-3
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------
SIST EN IEC 62841-3-5:2022
– 2 – IEC 62841-3-5:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirements . 8
5 General conditions for the tests . 9
6 Radiation, toxicity and similar hazards . 9
7 Classification . 9
8 Marking and instructions . 9
9 Protection against access to live parts . 10
10 Starting . 10
11 Input and current . 10
12 Heating . 10
13 Resistance to heat and fire . 10
14 Moisture resistance . 10
15 Resistance to rusting . 10
16 Overload protection of transformers and associated circuits . 11
17 Endurance . 11
18 Abnormal operation . 11
19 Mechanical hazards . 11
20 Mechanical strength . 16
21 Construction . 16
22 Internal wiring . 17
23 Components . 17
24 Supply connection and external flexible cords . 17
25 Terminals for external conductors . 17
26 Provision for earthing . 17
27 Screws and connections . 17
28 Creepage distances, clearances and distances through insulation . 17
Annexes . 18
Annex I (informative) Measurement of noise and vibration emissions . 18
Annex AA (normative) Requirements for interlocked access cover for band saws . 20
Bibliography . 21

Figure 101 – Parts of a typical band saw. 8
Figure 102 – Test probe . 13
Figure 103 – Table and fence dimensions . 14
Figure 104 – Cross-cutting fence . 15
Figure 105 – Saw band guides . 16

---------------------- Page: 6 ----------------------
SIST EN IEC 62841-3-5:2022
IEC 62841-3-5:2022 © IEC 2022 – 3 –
Table 4 – Required performance levels . 11
Table I.101 – Noise test conditions for band saws that are not intended for cutting
metal . 18
Table I.102 – Test conditions for band saws that are intended for cutting metal . 19

---------------------- Page: 7 ----------------------
SIST EN IEC 62841-3-5:2022
– 4 – IEC 62841-3-5:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –

Part 3-5: Particular requirements for transportable band saws

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of
IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other
IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 62841-3-5 has been prepared by IEC technical committee 116: Safety of motor-operated
electric tools. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
116/574/FDIS 116/585/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 8 ----------------------
SIST EN IEC 62841-3-5:2022
IEC 62841-3-5:2022 © IEC 2022 – 5 –
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
This Part 3-5 is to be used in conjunction with the first edition of IEC 62841-1:2014.
This Part 3-5 supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as
to convert it into the IEC Standard: Particular requirements for transportable band saws.
Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-5, that
subclause applies as far as relevant. Where this standard states "addition", "modification" or
"replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
notes: in small roman type.
–
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in IEC 62841-1:2014 are
numbered starting from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated hand-
held tools, transportable tools and lawn and garden machinery – Safety, can be found on the
IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally
not earlier than 36 months from the date of publication.

---------------------- Page: 9 ----------------------
SIST EN IEC 62841-3-5:2022
– 6 – IEC 62841-3-5:2022 © IEC 2022
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –

Part 3-5: Particular requirements for transportable band saws



1 Scope
IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition:
This document applies to band saws intended for cutting wood and analogous materials,
plastics and metals, except magnesium.
This document does not apply to transportable scroll saws and jig saws with a reciprocating
blade.
This document does not apply to
– hand-held band saws;
– non-vertical saws; and
– wire saws.
NOTE 101 It is planned that a document on transportable scroll saws and jig saws will be published.
NOTE 102 Hand-held band saws will be covered by a future part of IEC 62841-2.
NOTE 103 In Europe (EN IEC 62841-3-5), the following conditions apply:
This document does not apply to stationary band saws intended to cut wood and similar materials. Stationary band
saws that are intended to cut wood and similar materials are covered by EN 1807-1.
This document applies to band saws having a mass of:
– maximum 25 kg for tools capable of being lifted by hand by one person;
– maximum 50 kg for tools capable of being lifted by hand by two persons.
2 Normative references
IEC 62841-1:2014, Clause 2 is applicable, except as follows.
Addition:
IEC 62841-1:2014, Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety – Part 1: General requirements

---------------------- Page: 10 ----------------------
SIST EN IEC 62841-3-5:2022
IEC 62841-3-5:2022 © IEC 2022 – 7 –
3 Terms and definitions
IEC 62841-1:2014, Clause 3 is applicable, except as follows.
Addition:
3.101
band saw
tool designed to cut materials by means of a vertical revolving endless saw band which is
carried on two or more band wheels
Note 101 to entry: Band saws have a table to support and position the workpiece that is fed by hand against the
saw band. See Figure 101.
3.102
cross-cutting fence
device to guide or position the workpiece during the cutting process that is designed to move
parallel with the plane of the saw band
Note 101 to entry: The cross-cutting fence may have provisions to adjust the workpiece gu
...