Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions

This document specifies a laboratory method of determining the minimum pressing time for line thicknesses close contact, 0,2 mm, 0,3 mm and 0,5 mm, at three temperatures and three wood moisture contents.
This document is intended to determine the minimum pressing time using a defined procedure for obtaining a reliable base for comparison of minimum pressing time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence in variation of factors such as timber density, moisture content, factory temperature and relative air humidity.

Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste - Prüfverfahren - Teil 5: Bestimmung der Mindestpresszeit bei Referenzbedingungen

Dieses Dokument legt ein Laborverfahren zur Bestimmung der Mindestpresszeit für die Klebstofffugendicken dünn, 0,2 mm, 0,3 mm und 0,5 mm bei drei Temperaturen und drei Holzfeuchten fest.
Dieses Dokument ist zur Bestimmung der Mindestpresszeit mit einem festgelegten Verfahren vorgesehen, um eine zuverlässige Grundlage zum Vergleich der Mindestpresszeiten verschiedener Klebstoffe bei Referenzbedingungen zu schaffen.
Das Verfahren führt zu einem Ergebnis, das für die sichere Herstellung von Holzbauteilen nur unter Berücksichtigung der Einflussfaktoren, wie z. B. Rohdichte und Feuchtegehalt des Holzes, Werkstemperatur und relative Luftfeuchte, zugrunde gelegt werden kann.

Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste - Méthodes d'essais - Partie 5 : Détermination du temps de pressage minimal dans des conditions de référence

Le présent document spécifie une méthode de détermination en laboratoire du temps de pressage minimal pour des joints minces de 0,2 mm, 0,3 mm et 0,5 mm, à trois températures et trois teneurs en humidité du bois.
Le présent document est destiné à déterminer le temps de pressage minimal en utilisant un mode opératoire défini afin d’obtenir une base fiable de comparaison des temps de pressage minimaux de différents adhésifs dans des conditions de référence.
La méthode conduit à un résultat qui ne peut pas être utilisé pour une fabrication sûre des structures en bois sans tenir compte de l’influence de facteurs tels que la masse volumique du bois, sa teneur en humidité, la température de l’usine et l’humidité relative de l’air.

Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne metode - 5. del: Ugotavljanje najkrajšega časa stiskanja pri referenčnih pogojih

General Information

Status
Not Published
Public Enquiry End Date
29-Jun-2024
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
07-May-2024
Due Date
24-Sep-2024

Relations

Buy Standard

Draft
prEN 15416-5:2024
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15416-5:2024
01-junij-2024
Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne
metode - 5. del: Ugotavljanje najkrajšega časa stiskanja pri referenčnih pogojih
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test
methods - Part 5: Determination of minimum pressing time under referenced conditions
Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und
Aminoplaste - Prüfverfahren - Teil 5: Bestimmung der Mindestpresszeit bei
Referenzbedingungen
Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste -
Méthodes d'essais - Partie 5 : Détermination du temps de pressage minimal dans des
conditions de référence
Ta slovenski standard je istoveten z: prEN 15416-5
ICS:
83.180 Lepila Adhesives
91.080.20 Lesene konstrukcije Timber structures
oSIST prEN 15416-5:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15416-5:2024

---------------------- Page: 2 ----------------------
oSIST prEN 15416-5:2024


DRAFT
EUROPEAN STANDARD
prEN 15416-5
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2024
ICS 83.180 Will supersede EN 15416-5:2017
English Version

Adhesives for load bearing timber structures other than
phenolic and aminoplastic - Test methods - Part 5:
Determination of minimum pressing time under
referenced conditions
Adhésifs pour structures portantes en bois de type Klebstoffe für tragende Holzbauteile ausgenommen
autre que phénolique et aminoplaste - Méthodes Phenolharzklebstoffe und Aminoplaste - Prüfverfahren
d'essais - Partie 5 : Détermination du temps de - Teil 5: Bestimmung der Mindestpresszeit bei
pressage minimal dans des conditions de référence Referenzbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 193.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15416-5:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15416-5:2024
prEN 15416-5:2024 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 8
5 Apparatus .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.