SIST EN ISO 1452-2:2010

SLOVENSKI STANDARD
01-april-2010
1DGRPHãþD
SIST EN 1452-2:2000
SIST EN 1456-1:2002
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRVNUER]YRGRLQ]DSRG]HPQRLQ
QDG]HPQRRGYRGQMDYDQMHLQNDQDOL]DFLMRSRGWODNRP1HPHKþDQSROLYLQLONORULG
39&8GHO&HYL,62
Plastics piping systems for water supply and for buried and above-ground drainage and
sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes
(ISO 1452-2:2009)
Kunststoff-Rohrleitungssysteme für die Wasserversorgung und für erdverlegte und nicht
erdverlegte Entwässerungs- und Abwasserdruckleitungen - Weichmacherfreies
Polyvinylchlorid (PVC-U) - Teil 2: Rohre (ISO 1452-2:2009)
Systèmes de canalisations en plastique pour l'adduction d'eau, pour le drainage enterré
et en surface, et pour le réseau d'égout sous pression - Poly(chlorure de vinyle) non
plastifié (PVC-U) - Partie 2: Tubes (avec ou sans emboîtures incorporées) (ISO 1452-
2:2009)
Ta slovenski standard je istoveten z: EN ISO 1452-2:2009
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 1452-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2009
ICS 91.140.60; 93.025; 23.040.20; 23.040.45 Supersedes EN 1452-2:1999, EN 1456-1:2001
English Version
Plastics piping systems for water supply and for buried and
above-ground drainage and sewerage under pressure -
Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes (ISO
1452-2:2009)
Systèmes de canalisations en plastique pour l'alimentation Kunststoff-Rohrleitungssysteme für die Wasserversorgung
en eau, pour branchements et collecteurs d'assainissement und für erdverlegte und nicht erdverlegte Entwässerungs-
enterrés et aériens avec pression - Poly(chlorure de vinyle) und Abwasserdruckleitungen - Weichmacherfreies
non plastifié (PVC-U) - Partie 2: Tubes (ISO 1452-2:2009) Polyvinylchlorid (PVC-U) - Teil 2: Rohre (ISO 1452-2:2009)
This European Standard was approved by CEN on 4 November 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1452-2:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 1452-2:2009) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at
the latest by June 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1452-2:1999, EN 1456-1:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
INTERNATIONAL ISO
STANDARD 1452-2
First edition
2009-12-01
Plastics piping systems for water supply
and for buried and above-ground
drainage and sewerage under pressure —
Unplasticized poly(vinyl chloride)
(PVC-U) —
Part 2:
Pipes
Systèmes de canalisations en plastique pour l'alimentation en eau, pour
branchements et collecteurs d'assainissement enterrés et aériens avec
pression — Poly(chlorure de vinyle) non plastifié (PVC-U) —
Partie 2: Tubes
Reference number
ISO 1452-2:2009(E)
©
ISO 2009
ISO 1452-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

ISO 1452-2:2009(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms, definitions, symbols and abbreviated terms .2
4 Material .3
4.1 Pipe material .3
4.2 Density.3
4.3 MRS-value .3
5 General characteristics.3
5.1 Appearance .3
5.2 Colour .3
5.3 Opacity of pipes intended for the above-ground conveyance of water .3
6 Geometrical characteristics .3
6.1 Measurement of dimensions.3
6.2 Nominal outside diameters.3
6.3 Mean outside diameters and their tolerances .4
6.4 Wall thickness and their tolerances .5
6.5 Length of pipe.6
6.6 Pipes with sockets .7
6.7 Pipe ends for ring seal or solvent cement joints .11
7 Classification and selection of pipes .11
7.1 Classification .11
7.2 Selection of nominal pressure and pipe series S for water up to and including 25 °C .11
7.3 Determination of the allowable operating pressure for water up to 45 °C .11
8 Mechanical characteristics.11
8.1 Impact strength.11
8.2 Resistance to internal pressure.12
9 Physical characteristics.13
10 Sealing rings .14
11 Adhesives.14
12 Performance requirements.14
13 Marking.14
13.1 General .14
13.2 Minimum required marking .14
13.3 Additional marking .15
Annex A (normative) Allowable operating pressures .16
Annex B (normative) Imperial (inch)-sized pipes .18
Bibliography.23

ISO 1452-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1452-2 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This first edition cancels and replaces ISO 4422-2:1996 and ISO 2045, which have been technically revised.
ISO 1452 consists of the following parts, under the general title Plastics piping systems for water supply and
for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride)
(PVC-U):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 4: Valves
⎯ Part 5: Fitness for purpose of the system
Guidance for the assessment of conformity is to form the subject of a part 7.
iv © ISO 2009 – All rights reserved

ISO 1452-2:2009(E)
Introduction
The System Standard, of which this is Part 2, specifies the requirements for a piping system and its
components made from unplasticized poly(vinyl chloride) (PVC-U). The piping system is intended to be used
for water supply and for buried and above-ground drainage and sewerage under pressure.
In respect of potential adverse effects on the quality of water intended for human consumption, caused by the
products covered by this part of ISO 1452, the following are relevant.
a) This part of ISO 1452 provides no information as to whether or not the products can be used without
restriction.
b) Existing national regulations concerning the use and/or the characteristics of these products remain in
force.
Requirements and test methods for material and components, other than pipes, are specified in ISO 1452-1,
ISO 1452-3 and ISO 1452-4. Characteristics for fitness for purpose (mainly for joints) are established in
ISO 1452-5.
This part of ISO 1452 specifies the characteristics of pipes.
[1]
Guidance for installation is given in ISO/TR 4191 .
[2]
Guidance for assessment of conformity is provided in ENV 1452-7 .

INTERNATIONAL STANDARD ISO 1452-2:2009(E)

Plastics piping systems for water supply and for buried and
above-ground drainage and sewerage under pressure —
Unplasticized poly(vinyl chloride) (PVC-U) —
Part 2:
Pipes
1 Scope
This part of ISO 1452 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl
chloride) (PVC-U) for piping systems intended for water supply and for buried and above-ground drainage and
sewerage under pressure.
It also specifies the test parameters for the test methods referred to in this part of ISO 1452.
In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC-U pipes without a socket and
pipes with a socket (integral or not), intended to be used for the following:
a) water mains and services buried in the ground;
b) conveyance of water above ground for both outside and inside buildings;
c) buried and above-ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C
(cold water) intended for human consumption and for general purposes as well as for waste water under
pressure.
This part of ISO 1452 specifies pipes for the conveyance of water and waste water up to and including 45 °C.
For temperatures between 25 °C and 45 °C, Figure A.1 applies.
NOTE 1 The producer and the end-user can come to agreement on the possibilities of use for temperatures above
45 °C on a case-by-case basis.
This part of ISO 1452 specifies a range of pipe sizes and pressure classes, and gives requirements
concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 1: General method
ISO 1452-2:2009(E)
ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of
the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 1183-1:2004, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1452-1:2009, Plastics piping systems for water supply and for buried and above-ground drainage and
sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC U) — Part 1: General
ISO 1452-5, Plastics piping systems for water supply and for buried and above-ground drainage and
sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC U) — Part 5: Fitness for purpose of the
system
ISO 2505, Thermoplastics pipes — Longitudinal reversion — Test method and parameters
ISO 2507-1:1995, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test
method
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 6259-1, Thermoplastics pipes — Determination of tensile properties — Part 1: General test method
ISO 6259-2, Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of
unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl
chloride) (PVC-HI)
ISO 7387-1, Adhesives with solvents for assembly of PVC-U pipe elements — Characterization — Part 1:
Basic test methods
ISO 7686, Plastics pipes and fittings — Determination of opacity
ISO 9311-1, Adhesives for thermoplastic piping systems — Part 1: Determination of film properties
ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified
temperature (DCMT) — Test method
ISO 18373-1, Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of
the processing temperature
EN 681-1:1996, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 744:1995, Plastics piping and ducting systems — Thermoplastics pipes — Test method for resistance to
external blows by the round-the-clock method
3 Terms, definitions, symbols and abbreviated terms
For the purposes of this document, the terms, definitions, symbols and abbreviated terms given in ISO 1452-1
and the following apply:
L length of socket
m depth of engagement
2 © ISO 2009 – All rights reserved

ISO 1452-2:2009(E)
4 Material
4.1 Pipe material
The material to be used shall conform to ISO 1452-1 and to the requirements given in 4.2 and 4.3.
4.2 Density
The density, ρ, at 23 °C of the pipe, when measured in accordance with ISO 1183-1, shall be within the
following limits:
3 3
1 350 kg/m u ρ u 1 460 kg/m
4.3 MRS-value
The pipe material shall have a minimum required strength, MRS, as defined in ISO 1452-1:2009, 4.4.1, of at
least 25 MPa.
The manufacturer of the compound or formulation shall confirm the MRS by testing as described in
ISO 1452-1:2009, 4.4.1 or 4.4.2, respectively.
5 General characteristics
5.1 Appearance
When viewed without magnification the internal and external surfaces of pipes shall be smooth, clean and free
from scoring, cavities and other surface defects to an extent that would prevent conformity to this part of
ISO 1452. The material shall not contain any impurities visible without magnification. The ends of the pipe
shall be cut cleanly and square to the axis of the pipe.
5.2 Colour
The colour of the pipes shall be either grey, blue or cream for water supply, and grey or brown for drainage
and sewerage under pressure. The colour of the pipes shall be uniform throughout the wall.
NOTE Attention is drawn to the fact that the colouring of pipes for the supply of water for human consumption can be
part of national regulation.
5.3 Opacity of pipes intended for the above-ground conveyance of water
The wall of the pipe shall be opaque and shall not transmit more than 0,2 % of visible light when measured in
accordance with ISO 7686.
6 Geometrical characteristics
6.1 Measurement of dimensions
Dimensions shall be measured in accordance with ISO 3126.
6.2 Nominal outside diameters
The nominal outside diameter, d , of a pipe shall conform to Table 1.
n
ISO 1452-2:2009(E)
6.3 Mean outside diameters and their tolerances
The mean outside diameter, d , of a pipe shall conform to the applicable nominal outside diameter, d , within
em n
the tolerance given in Table 1.
The tolerance for out-of-roundness shall conform to Table 1.
Table 1 — Nominal outside diameters and tolerances
Dimensions in millimetres
b
Nominal outside Tolerance for mean Tolerance for out-of-roundness
a
diameter outside diameter, d
em
c d
d x S 20 to S 16 S 12,5 to S 5
n
12 0,2 — 0,5
16 0,2 — 0,5
20 0,2 — 0,5
25 0,2 — 0,5
32 0,2 — 0,5
40 0,2 1,4 0,5
50 0,2 1,4 0,6
63 0,3 1,5 0,8
75 0,3 1,6 0,9
90 0,3 1,8 1,1
110 0,4 2,2 1,4
125 0,4 2,5 1,5
140 0,5 2,8 1,7
160 0,5 3,2 2,0
180 0,6 3,6 2,2
200 0,6 4,0 2,4
225 0,7 4,5 2,7
250 0,8 5,0 3,0
280 0,9 6,8 3,4
315 1,0 7,6 3,8
355 1,1 8,6 4,3
400 1,2 9,6 4,8
450 1,4 10,8 5,4
500 1,5 12,0 6,0
560 1,7 13,5 6,8
630 1,9 15,2 7,6
710 2,0 17,1 8,6
800 2,0 19,2 9,6
900 2,0 21,6 —
1 000 2,0 24,0 —
a [3]
The tolerance conforms to grade D of ISO 11922-1 for d u 50 and to grade C for d > 50. The tolerance
n n
+ x
is expressed in the form mm, where x is the value of the tolerance.
b
The tolerance is expressed as the difference between the largest and the smallest outside diameter in a
cross-section of the pipe (i.e. d − d ).
e, max e, min
c [3]
For d u 250, the tolerance conforms to grade N of ISO 11922-1 .
n
[3]
For d > 250, the tolerance conforms to grade M of ISO 11922-1 . The requirement for out-of-roundness is only
n
applicable prior to storage.
d [3]
For a d of 12 to 1 000, the tolerance conforms to 0,5 grade M of ISO 11922-1 . The requirement for out-
n
of-roundness is only applicable prior to the pipe leaving the manufacturer's premises.

4 © ISO 2009 – All rights reserved

ISO 1452-2:2009(E)
6.4 Wall thickness and their tolerances
The nominal wall thickness, e , is classified with the pipe series S. The nominal wall thickness corresponds to
n
the minimum allowable wall thickness.
The nominal wall thickness shall conform to Table 2, as appropriate to the pipe series.
The tolerance for wall thickness, e, shall conform to Table 3.
Table 2 — Nominal (minimum) wall thicknesses
Pipe series S
Nominal (minimum) wall thickness
Nominal
outside
S 20 S 16 S 12,5 S 10 S 8 S 6,3 S 5
diameter,
(SDR 41) (SDR 33) (SDR 26) (SDR 21) (SDR 17) (SDR 13,6) (SDR 11)
d
n
Nominal pressure PN based on design coefficient C = 2,5
PN 6 PN 8 PN 10 PN 12,5 PN 16 PN 20
12 — — — — — 1,5
16 — — — — — 1,5
20 — — — — 1,5 1,9
25 — — — 1,5 1,9 2,3
32 — 1,5 1,6 1,9 2,4 2,9
40 1,5 1,6 1,9 2,4 3,0 3,7
50 1,6 2,0 2,4 3,0 3,7 4,6
63 2,0 2,5 3,0 3,8 4,7 5,8
75 2,3 2,9 3,6 4,5 5,6 6,8
90 2,8 3,5 4,3 5,4 6,7 8,2
a
Nominal pressure PN based on design coefficient C = 2,0
PN 6 PN 8 PN 10 PN 12,5 PN 16 P
...