SIST EN 13892-5:2003
(Main)Methods of test for screed materials - Part 5: Determination of wear resistance to rolling wheel of screed material for wearing layer
Methods of test for screed materials - Part 5: Determination of wear resistance to rolling wheel of screed material for wearing layer
This European Standard specifies a method for determining the wear resistance to a heavily loaded rolling wheel on moulded mortar specimens made from cementitious screed- and synthetic resin screed material or optionally for other screed materials for wearing surface.
Prüfverfahren für Estrichmörtel und Estrichmassen - Teil 5: Bestimmung des Widerstandes gegen Rollbeanspruchung von Estrichen für Nutzschichten
Méthodes d'essais des matériaux de chape - Partie 5: Détermination de la résistance a l'usure par roulette pivotante des matériaux de chape avec couche d'usure
La présente Norme européenne spécifie une méthode permettant de déterminer la résistance à l'usure due au roulement d'une roue lourdement chargée, sur des éprouvettes de mortier moulées, confectionnées avec des matériaux pour chapes à base ciment ou de résine synthétique utilisés en couche d'usure. Cette méthode peut s'appliquer, le cas échéant, à d'autres matériaux de chape utilisés en couche d'usure.
Metode preskušanja za mešanice za estrih – 5. del: Določevanje odpornosti mešanice za estrih za obrabno plast proti obrabi zaradi koles
General Information
Overview
EN 13892-5:2003 - Methods of test for screed materials, Part 5 - specifies a laboratory method to determine the wear resistance to a heavily loaded rolling wheel of screed materials intended as wearing layers. The standard applies to moulded specimens of cementitious screed and synthetic resin screed (and optionally other screed materials), assessing abrasion caused by repeated passages of a loaded swivel castor (rolling wheel).
Key topics and technical requirements
- Test principle: Repeated passages of a heavily loaded swivel castor produce combined normal and shear stresses; wear is quantified from change in surface profile.
- Specimens: Three moulded slabs (minimum 500 mm edge, thickness ≥ 50 mm) prepared and cured in accordance with EN 13892-1. Surface must be dry and free of contaminants.
- Test rig and movement:
- Longitudinal travel: (390 ± 2) mm at (7.0 ± 0.4) cycles/min.
- Transverse travel: (260 ± 2) mm at (1.72 ± 0.1) cycles/min.
- Frequency ratio ≈ 4.07 to avoid repeat wheel paths.
- Swivel castor (rolling wheel):
- Solid case-hardened steel wheel (Vickers hardness ≈ 735 HV over outer 1.5 mm).
- Diameter (125 ± 2) mm, width (40 ± 1) mm, overhang (45 ± 1) mm.
- Total applied load: (2000 ± 10) N.
- Abrasive debris removal: Suction nozzles / vacuum to continuously remove abraded material.
- Measurement:
- Depth gauge readable to 10 µm; profile measured via a rigid bridge with defined positions.
- Test duration: 10 000 cycles in the long direction (≈ 24 h); stop earlier if severe damage or substrate exposure occurs.
- Calculation: abrasion volume RWA is derived from mean depth d (µm). Using the standard’s assumption of an abraded area of 1 100 cm²:
- RWA (cm³) = d (µm) × 11.0
- Test report: Comprehensive documentation including specimen identification, preparation conditions, apparatus details, individual and mean results, and remarks (per clause 8).
Applications and users
EN 13892-5:2003 is used for:
- Product development and comparative screed testing (cementitious and resin screeds).
- Quality control and factory/laboratory acceptance testing.
- Specification and compliance checks for floor wearing layers in commercial, industrial and public buildings.
- Decision-making by flooring manufacturers, independent test laboratories, architects, specifiers and contractors concerned with abrasion resistance, durability and expected service life.
Related standards
- EN 13892-1 (sampling, making and curing specimens)
- EN 13813 (screed material properties and requirements)
- EN 1818 (resilient floor coverings / related test rig)
- EN 10084, ISO 606 (referenced for materials and transmission details)
Keywords: EN 13892-5:2003, wear resistance, rolling wheel, screed material, screed testing, cementitious screed, synthetic resin screed, abrasion resistance, castor wheel, test rig.
Frequently Asked Questions
SIST EN 13892-5:2003 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Methods of test for screed materials - Part 5: Determination of wear resistance to rolling wheel of screed material for wearing layer". This standard covers: This European Standard specifies a method for determining the wear resistance to a heavily loaded rolling wheel on moulded mortar specimens made from cementitious screed- and synthetic resin screed material or optionally for other screed materials for wearing surface.
This European Standard specifies a method for determining the wear resistance to a heavily loaded rolling wheel on moulded mortar specimens made from cementitious screed- and synthetic resin screed material or optionally for other screed materials for wearing surface.
SIST EN 13892-5:2003 is classified under the following ICS (International Classification for Standards) categories: 91.100.10 - Cement. Gypsum. Lime. Mortar. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 13892-5:2003 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 13892-5:2003 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SRUQRVWLPrüfverfahren für Estrichmörtel und Estrichmassen - Teil 5: Bestimmung des Widerstandes gegen Rollbeanspruchung von Estrichen für NutzschichtenMéthodes d'essais des matériaux de chape - Partie 5: Détermination de la résistance a l'usure par roulette pivotante des matériaux de chape avec couche d'usureMethods of test for screed materials - Part 5: Determination of wear resistance to rolling wheel of screed material for wearing layer91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. MortarICS:Ta slovenski standard je istoveten z:EN 13892-5:2003SIST EN 13892-5:2003en01-september-2003SIST EN 13892-5:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13892-5June 2003ICS 91.100.10English versionMethods of test for screed materials - Part 5: Determination ofwear resistance to rolling wheel of screed material for wearinglayerMéthodes d'essais des matériaux de chape - Partie 5:Détermination de la résistance à l'usure par roulettepivotante - Méthodes pour matériaux de chape aveccouche d'usurePrüfverfahren für Estrichmörtel und Estrichmassen - Teil 5:Bestimmung des Widerstandes gegen Rollbeanspruchungvon Estrichen für NutzschichtenThis European Standard was approved by CEN on 3 April 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13892-5:2003 ESIST EN 13892-5:2003
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...