SIST EN ISO 25178-601:2025

SLOVENSKI STANDARD
01-maj-2025
Specifikacija geometrijskih veličin izdelka - Tekstura površine: ploskovna - 601.
del: Konstrukcije in značilnosti kontaktnih (s tipalom) instrumentov (ISO 25178-
601:2025)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 601: Design and
characteristics of contact (stylus) instruments (ISO 25178-601:2025)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 601: Aufbau und Merkmale von berührend messenden Geräten (mit Taster) (ISO
25178-601:2025)
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 601:
Conception et caractéristiques des instruments à contact (à stylet) (ISO 25178-
601:2025)
Ta slovenski standard je istoveten z: EN ISO 25178-601:2025
ICS:
17.040.20 Lastnosti površin Properties of surfaces
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 25178-601
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2025
EUROPÄISCHE NORM
ICS 17.040.20 Supersedes EN ISO 25178-601:2010
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 601: Design and characteristics of contact
(stylus) instruments (ISO 25178-601:2025)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 601: Conception et Oberflächenbeschaffenheit: Flächenhaft - Teil 601:
caractéristiques des instruments à contact (palpeur) Aufbau und Merkmale von berührend messenden
(ISO 25178-601:2025) Geräten (mit Taster) (ISO 25178-601:2025)
This European Standard was approved by CEN on 21 February 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-601:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 25178-601:2025) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2025, and conflicting national standards shall
be withdrawn at the latest by August 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 25178-601:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 25178-601:2025 has been approved by CEN as EN ISO 25178-601:2025 without any
modification.
International
Standard
ISO 25178-601
Second edition
Geometrical product specifications
2025-02
(GPS) — Surface texture: Areal —
Part 601:
Design and characteristics of
contact (stylus) instruments
Spécification géométrique des produits (GPS) — État de surface:
Surfacique —
Partie 601: Conception et caractéristiques des instruments à
contact (palpeur)
Reference number
ISO 25178-601:2025(en) © ISO 2025

ISO 25178-601:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 25178-601:2025(en)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Instrument requirements . 4
5 Metrological characteristics . 4
6 Design features . 5
6.1 General .5
6.2 Nominal values for characteristics of a contact stylus instrument .5
6.2.1 Stylus tip geometry .5
6.2.2 Static measuring force.5
7 General information . 5
Annex A (informative) Principles of contact stylus instruments for areal surface topography
measurement . 6
Annex B (informative) Sources of measurement error for contact stylus instruments .11
Annex C (informative) Background regarding changes from ISO 3274 .13
Annex D (informative) Relationship to the GPS matrix model .15
Bibliography .16

iii
ISO 25178-601:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 290, Dimensional and geometrical product specification and verification, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 25178-601:2010), which has been technically
revised, and cancels and replaces ISO 3274:1996, whose contents have been revised and incorporated into
this document and others, see Annex C for more information.
The main changes are as follows:
— removal of information about the general metrological characteristics for the areal topography measuring
method, which are specified in ISO 25178-600;
— removal of the terms and definitions now specified in ISO 25178-600;
— revision of all terms and definitions for clarity and consistency with other ISO standards documents;
— addition of Clause 4 for instrument requirements, which summarizes normative features and
characteristics;
— addition of an information flow concept diagram in Clause 4;
— addition of Clause 5 on metrological characteristics;
— addition of Clause 6 on design features, which clarifies the types of instruments relevant to this document;
— revision of Annex A describing the principles of instruments addressed by this document;
— addition of Annex B on the metrological characteristics and influence quantities; replacement of the
normative table of influence quantities with an informative description of common error sources and
how these relate to the metrological characteristics in ISO 25178-600;

iv
...