SIST EN 15416-4:2017
(Main)Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions
This European Standard specifies a laboratory method of determining the open assembly time in a standard atmosphere [20/65].
This European Standard is intended to determine the open assembly time using a defined procedure for obtaining a reliable base for comparison of open assembly time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence of factors such as timber density, moisture content, factory temperature and relative air humidity.
Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste - Prüfverfahren - Teil 4: Bestimmung der offenen Wartezeit bei Referenzbedingungen
Diese Europäische Norm legt ein Laborverfahren zur Bestimmung der offenen Wartezeit in einem Normal¬klima [20/65] fest.
Diese Europäische Norm dient zur Bestimmung der offenen Wartezeit unter Anwendung eines festgelegten Verfahrens, um eine zuverlässige Grundlage zum Vergleich der offenen Wartezeiten verschiedener Klebstoffe bei Referenzbedingungen zu schaffen.
Das Verfahren führt zu einem Ergebnis, das für die sichere Herstellung von Holzbauteilen nur unter Berück-sichtigung der Einflussfaktoren, wie z. B. Rohdichte/Feuchtegehalt des Holzes, Werkstemperatur und relative Luftfeuchte, zugrunde gelegt werden kann.
Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste - Méthodes d'essais - Partie 4 : Détermination du temps d'assemblage ouvert dans des conditions de référence
La présente Norme européenne spécifie une méthode de détermination en laboratoire du temps d’assemblage ouvert dans une atmosphère normale (20/65).
Le présent document est destiné à déterminer le temps d’assemblage ouvert en utilisant un mode opératoire défini afin d’obtenir une base fiable de comparaison des temps d’assemblage ouvert de différents adhésifs dans des conditions de référence.
La méthode conduit à un résultat qui ne peut pas être utilisé pour une fabrication sûre des structures en bois sans tenir compte de l’influence de facteurs tels que la masse volumique du bois, sa teneur en humidité, la température de l’usine et l’humidité relative de l’air.
Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne metode - 4. del: Ugotavljanje odprtega časa pri referenčnih pogojih
Ta evropski standard določa laboratorijsko metodo za določanje odprtega časa montaže v standardni atmosferi [20/65].
Ta evropski standard je namenjen za določanje odprtega časa montaže z določenim postopkom za pridobivanje zanesljive podlage za primerjavo odprtega časa montaže med lepili pri referenčnih pogojih.
Z metodo se pridobi rezultat, ki ga ni mogoče uporabiti za varno proizvodnjo lesenih konstrukcij brez upoštevanja vplivov dejavnikov, kot so gostota lesa, vsebnost vlage, tovarniška temperatura in relativna vlažnost zraka.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LKKlebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste - Prüfverfahren - Teil 4: Bestimmung der offenen Wartezeit bei ReferenzbedingungenAdhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste - Méthodes d'essais - Partie 4 : Détermination du temps d'assemblage ouvert dans des conditions de référenceAdhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions91.080.20Lesene konstrukcijeTimber structures83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 15416-4:2017SIST EN 15416-4:2017en,fr,de01-april-2017SIST EN 15416-4:2017SLOVENSKI
STANDARDSIST EN 15416-4:20061DGRPHãþD
SIST EN 15416-4:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15416-4
January
t r s y ICS
z uä s z r Supersedes EN
s w v s xæ vã t r r xEnglish Version
Adhesives for load bearing timber structures other than phenolic and aminoplastic æ Test methods æ Part
vã Determination of open assembly time under referenced conditions Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste æ Méthodes d 5essais æ Partie
v ã Détermination du temps d 5assemblage ouvert dans des conditions de référence Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste æ Prüfverfahren æ Teil
vã Bestimmung der offenen Wartezeit bei Referenzbedingungen This European Standard was approved by CEN on
u r October
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s w v s xæ vã t r s y ESIST EN 15416-4:2017
EN 15416-4:2017 (E) 2 Contents Page European foreword . 3 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 4 Principle . 6 5 Apparatus . 6 6 Procedure. 7 6.1 General . 7 6.2 Preparation of bonded assemblies . 7 6.3 Preparation of samples for testing . 8 6.4 Test procedure . 8 7 Expression of results . 8 7.1 Tensile shear strength . 8 7.2 Failure mode . 8 8 Requirement . 8 9 Test report . 8 9.1 General information . 8 9.2 Information about the adhesive . 9 9.3 Preparation of test pieces and testing procedure . 9 9.4 Test results . 9
SIST EN 15416-4:2017
EN 15416-4:2017 (E) 3 European foreword This document (EN 15416-4:2017) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15416-4:2006. Compared to EN 15416-4:2006, the following main modifications have been made: a) title has been changed; b) 7.2 covering failure mode has been introduced; c) new definition of open assembly time has been given in 3.1; d) time intervals for open assembly times in Table 1 divided into slow and fast systems; e) requirement has been added as Clause 8. This document is one of a series dealing with adhesives for use with timber structures, and is published in support of product standards for bonded load-bearing timber structures. The series consists of three classification and performance requirements for adhesives for load-bearing timber structures, phenolic and aminoplastic adhesives (EN 301), one component polyurethane adhesives (EN 15425) and emulsion polymerized isocyanate adhesives (EN 16254), together with 12 test methods (EN 302 Parts 1 to 8 and EN 15416 Parts 1 and 3 to 5). These European Standards have the following titles: — EN 301, Adhesives, phenolic and aminoplastic, for load-bearing timber structures — Classification and performance requirements — EN 15425, Adhesives — One component polyurethane (PUR) for load-bearing timber structures — Classification and performance requirements — EN 16254, Adhesives — Emulsion polymerized isocyanate (EPI) for load-bearing timber structures — Classification and performance requirements — EN 302-1, Adhesives for load-bearing timber structures — Test methods — Part 1: Determination of longitudinal tensile shear strength — EN 302-2, Adhesives for load-bearing timber structures — Test methods — Part 2: Determination of resistance to delamination — EN 302-3, Adhesives for load-bearing timber structures — Test methods — Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength SIST EN 15416-4:2017
EN 15416-4:2017 (E) 4 — EN 302-4, Adhesives for load-bearing timber structures — Test methods — Part 4: Determination of the effects of wood shrinkage on the shear strength — EN 302-5, Adhesives for load-bearing timber structures — Test methods — Part 5: Determination of maximum assembly time under referenced conditions — EN 302-6, Adhesives for load-bearing timber structures — Test methods — Part 6: Determination of the minimum pressing time under referenced conditions — EN 302-7, Adhesives for load-bearing timber structures — Test methods - Part 7: Determination of the working life under referenced conditions — EN 302-8, Adhesives for load-bearing timber structures — Test methods — Part 8: Static load test of multiple bond line specimens in compression shear — EN 15416-1, Adhesives for load bearing timber structures other than phenolic and aminoplastic — Test methods — Part 1: Long-term tension load test perpendicular to the bond line at varying climate conditions with specimens perpendicular to the glue line (Glass house test) — EN 15416-3, Adhesives for load bearing timber structures other than phenolic and aminoplastic — Test methods — Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear — EN 15416-4, Adhesi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.