SIST EN 13207:2002

SLOVENSKI STANDARD
SIST EN 13207:2002
01-februar-2002
Plastomerni filmi za siliranje
Silage thermoplastic films
Thermoplastische Silagefolien
Films thermoplastiques d'ensilage
Ta slovenski standard je istoveten z: EN 13207:2001
ICS:
65.040.20 3RVORSMDLQQDSUDYH]D Buildings and installations for
SUHGHODYRLQVNODGLãþHQMH processing and storage of
NPHWLMVNLKSULGHONRY agricultural produce
83.140.10 Filmi in folije Films and sheets
SIST EN 13207:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13207:2002

---------------------- Page: 2 ----------------------

SIST EN 13207:2002
EUROPEAN STANDARD
EN 13207
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2001
ICS 65.040.20; 83.140.10
English version
Silage thermoplastic films
Films thermoplastiques d'ensilage Thermoplastische Silagefolien
This European Standard was approved by CEN on 4 February 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13207:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13207:2002
Page 2
EN 13207:2001
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 249
"Plastics", the secretariat of which is held by IBN.
This European Standard shall be given the status of a national standard, either by
publication of an identical text or by endorsement, at the latest by September 2001, and
conflicting national standards shall be withdrawn at the latest by September 2001.
According to the CEN/CENELEC Internal Regulations, the national standards
organizations of the following countries are bound to implement this European Standard:
Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland,
Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland
and the United Kingdom

---------------------- Page: 4 ----------------------

SIST EN 13207:2002
Page 3
EN 13207:2001
1 Scope
This standard specifies the basic requirements for physical and mechanical characteristics
of films used during the manufacture of silage and designed to last at least one year for
protecting fodder.
The films are usually black, white or bicoloured (double face, black and white) and are
made of polyethylene and/or ethylene copolymers.
2 Normative references
This European Standard incorporates by dated or undated references, provisions from
other publications. These normative references are cited at the appropriate places in the
text and the publications are listed hereafter. For dated references subsequent
amendments to or revisions of any of these publications apply to this European Standard
only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies (including amendments).
EN ISO 527-1 Plastics - Determination of tensile properties - Part 1: General
principles (ISO 527-1:1993 including Corr 1:1994)
EN ISO 527-3 Plastics - Determination of tensile properties Part 3: Test conditions
for films and sheets (ISO 527-3:1995)
EN ISO 4892-2 Plastics - Methods of exposure to laboratory light sources - Part 2 :
Xenon-arc sources (ISO 4892-2:1994)
ISO 4591 Plastics - Film and sheeting - Determination of average thickness of
a sample and average thickness and yield of a roll by gravimetric
techniques (gravimetric thickness)
ISO 4592 Plastics - Film and sheeting - Determination of length and width
ISO 4593 Plastics - Film and sheeting - Determination of thickness by
mechanical scanning
ISO 7765-1:1988 Plastics film and sheeting - Determination of impact resistance by the
free falling dart method - Part 1: Staircase methods
3 Terms and definitions
For the purposes of this standard, the following terms and definitions apply.

---------------------- Page: 5 ----------------------

SIST EN 13207:2002
Page 4
EN 13207:2001
3.1
width
total width of the film when laid flat, given in millimetres. Films which are wider than 2000
mm are usually wound on a roll and folded lengthwise at least once
NOTE These folds are retained even when the film is laid out flat, and this may affect
test results. Therefore, a distinction shall be made between the sample sheets taken from
the folds ("fold" area) and sample sheets from areas which have not been folded ("flat
area").
3.2
nominal width
width declared by the manufacturer in mm
3.3
thickness
given in
m
3.4
nominal thickness
thickness declared by the manufacturer in
m
3.5
length of the roll
the largest dimension of the r
...