SIST EN 848-1:2007+A1:2010
(Main)Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines
Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines
This document !specifies all significant" hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable hand fed single spindle vertical moulding machines (with or without demountable power feed unit), herein after referred to as "machines", designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer. This document does not apply to: a) machines equipped with outboard bearings; b) machines equipped with powered movements of front extension table and/or tenoning travelling table; c) hand held woodworking machines or any adaptation permitting their use in a different mode, i.e. bench mounting; d) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down; This document is not applicable to hand fed single spindle vertical moulding machines which are manufactured before the date of its publication as EN.
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung mit drehendem Werkzeug - Teil 1: Einspindelige senkrechte Tischfräsmaschinen
Dieses Dokument !spezifiziert alle" im Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen
und Gefährdungsereignisse, die auf stationäre und verschiebbare einspindelige senkrechte
Tischfräsmaschinen (mit oder ohne abnehmbaren Vorschubapparat) zutreffen — im Folgenden als
„Maschinen“ bezeichnet —, die konstruiert sind zum Bearbeiten von Massivholz, Spanplatten, Faserplatten,
Sperrholz, sowie diesen Werkstoffen, wenn sie kunststoffbeschichtet oder mit Kunststoffkanten versehen sind,
wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers
verwendet werden.
ANMERKUNG 1 Hinsichtlich der Definition von stationärer und verschiebbarer Maschine siehe 3.2.17 und 3.2.18.
Dieses Dokument gilt nicht für:
a) Maschinen, die mit Oberlager ausgerüstet sind;
b) Maschinen, die mit kraftbetätigten Bewegungen einer vorderen Tischverbreiterung und/oder eines
Zapfenschneid-/Schlitztisches ausgerüstet sind;
c) handgeführte Holzbearbeitungsmaschinen einschließlich solcher Einrichtungen, die ihre Verwendung in
einer anderen Weise, z. B. in einer Stationäreinrichtung, ermöglichen;
ANMERKUNG 2 Handgeführte motorbetriebene Elektrowerkzeuge sind in EN 60745-1:2003 zusammen mit
EN 60745-2-17:2003 behandelt.
d) Maschinen, die auf ein Gestell oder auf einen Tisch, der einem Gestell ähnlich ist, aufgesetzt sind und die
vorgesehen sind, während des Betriebs stationär verwendet zu werden und die von einer Person von
Hand angehoben werden können. Das Gestell kann auch ein fester Bestandteil der Maschine sein, wenn
es aus scharnierbefestigten Füßen besteht, die heruntergeklappt werden können.
ANMERKUNG 3 Transportable motorbetriebene Elektrowerkzeuge sind in EN 61029-1:2000 zusammen mit
!EN 61029-2-8:2003" behandelt.
Dieses Dokument gilt nicht für einspindelige senkrechte Tischfräsmaschinen mit Handvorschub, die vor seiner
Veröffentlichung als EN hergestellt wurden.
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil rotatif - Partie 1: Toupies monobroches à arbre vertical
Le présent document !spécifie tous les phénomènes dangereux", des situations et événements dangereux significatifs, tels qu’énumérés à l'Article 4, applicables aux toupies fixe et déplaçable monobroche à axe vertical à avance manuelle, avec ou sans unité d'alimentation mécanisée escamotable, ci-après désignées comme «machines». Celles-ci sont conçues pour la coupe de bois massif, de panneaux de particules, de contre-plaqué, ainsi que ces matériaux si leurs surfaces ou leurs chants sont recouverts de matière plastique ou de plastique léger stratifié, durant l’utilisation normale et dans les conditions prévues par le fabricant.
NOTE 1 Pour la définition de machine fixe et machine transportable, voir 3.2.17 et 3.2.18.
La présente Norme européenne ne s’applique pas :
a) aux machines équipées de contre-paliers extérieurs ;
b) aux machines équipées de mouvements mécanisés d’allonge de table frontale et/ou du chariot de tenonnage ;
c) aux machines pour le travail du bois portatives ou toute adaptation permettant leur utilisation de manière différente, c'est-à-dire fixées sur un bâti ;
NOTE 2 Les outils électroportatifs à moteur sont traités dans l’EN 60745-1:2003 à utiliser conjointement avec l’EN 60745-2-17:2003.
d) aux machines montées sur un bâti, ou une table similaire à un bâti, conçues pour réaliser un travail à poste fixe et capables d'être soulevées à la main par une personne. Le bâti peut également être une partie intégrée à la machine s'il consiste en pieds articulés qui peuvent être dépliés.
NOTE 3 Les machines-outils semi-fixes électriques sont traitées dans l’EN 61029-1:2000 à utiliser conjointement avec l’!EN 61029-2-8:2003".
La présente Norme européenne ne s’applique pas aux toupies monobroche à axe vertical qui ont été fabriquées avant sa date de publication comme EN.
NOTE 4 Les machines concernées par le présent document sont listées dans l’Annexe IV, A.7, de la Directive «Machines».
Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 1. del: Enovretenski navpični rezkalni stroji
Ta dokument opredeljuje vse »velike« nevarnosti, nevarna stanja in dogodke, kot so našteti v Klavzuli 4, ki so pomembni za stacionarne in premestljive enovretenske navpične rezkalne stroje z ročnim podajanjem (z ali brez snemljive pogonske enote za podajanje), v nadaljevanju »stroji«, ki so zasnovani za rezanje masivnega lesa, ivernih plošč, plošč iz stisnjenih vlaken, vezanega lesa, kot tudi teh istih materialov, če so prekriti s plastičnim laminatom ali robovi, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, ki jih predvidi proizvajalec. Ta dokument se ne nanaša na: a) stroje, opremljene z zunajkrmnimi ležaji; b) stroje, opremljene s gibanjem prednje gnane izvlečene mize in/ali pomične mize z zatičem; c) ročno upravljane stroje za obdelavo lesa ali vsako prilagoditev, ki dovoljuje njihovo uporabo na drug način, t.j. montaža na delovno mizo; d) stroje, nameščene na delovno površino ali delovni površini podobno mizo, kateri so namenjeni opravljanju dela v stacionarnem položaju in jih lahko ena oseba dvigne z roko. Delovna površina je lahko tudi sestavni del stroja, če jo sestavljajo noge na tečajih, ki jih je mogoče raztegniti navzdol. Ta dokument ne velja za enovretenske navpične rezkalne stroje z ročnim podajanjem, ki so bili proizvedeni pred datumom, ko je dokument objavljen kot EN.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 848-1:2007+A1:2010
01-januar-2010
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWLOQLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO (QRYUHWHQVNLQDYSLþQLUH]NDOQLVWURML
Safety of woodworking machines - One side moulding machines with rotating tool - Part
1: Single spindle vertical moulding machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 1: Einspindelige senkrechte Tischfräsmaschinen
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 1: Toupies monobroches à arbre vertical
Ta slovenski standard je istoveten z: EN 848-1:2007+A1:2009
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 848-1:2007+A1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 848-1:2007+A1:2010
---------------------- Page: 2 ----------------------
SIST EN 848-1:2007+A1:2010
EUROPEAN STANDARD
EN 848-1:2007+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2009
ICS 79.120.10 Supersedes EN 848-1:2007
English Version
Safety of woodworking machines - One side moulding machines
with rotating tool - Part 1: Single spindle vertical moulding
machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 1: Toupies Fräsmaschinen für einseitige Bearbeitung mit drehendem
monobroches à arbre vertical Werkzeug - Teil 1: Einspindelige senkrechte
Tischfräsmaschinen
This European Standard was approved by CEN on 13 January 2007 and includes Amendment 1 approved by CEN on 3 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-1:2007+A1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .9
3.1 General .9
3.2 Definitions .9
3.3 Terminology . 14
4 List of significant hazards . 18
5 Safety requirements and/or measures . 21
5.1 General . 21
5.2 Controls . 21
5.2.1 Safety and reliability of control systems . 21
5.2.2 Position of controls . 22
5.2.3 Starting . 23
5.2.4 Normal stopping . 24
5.2.5 Emergency stop . 25
5.2.6 Mode selection . 25
5.2.7 Speed changing . 26
5.2.8 Adjustments control . 27
5.2.9 Failure of the power supply . 28
5.2.10 Failure of the control circuits . 28
5.3 Protection against mechanical hazards . 29
5.3.1 Stability . 29
5.3.2 Hazard of break-up during operation. 29
5.3.3 Tool holder and tool design . 29
5.3.4 Braking . 36
5.3.5 Devices to minimise the possibility or the effect of kickback . 37
5.3.6 Work-piece supports and guides . 40
5.3.7 Prevention of access to moving parts . 46
5.3.8 Workpiece clamping device . 51
5.3.9 Safety appliances. 51
5.4 Protection against non-mechanical hazards . 52
5.4.1 Fire . 52
5.4.2 Noise . 52
5.4.3 Emission of chips and dust . 53
5.4.4 Electricity . 54
5.4.5 Ergonomics and handling . 55
5.4.6 Pneumatics . 55
5.4.7 Hydraulics . 55
5.4.8 Electromagnetic compatibility . 55
5.4.9 Errors of fitting . 56
5.4.10 Supply disconnecting devices . 56
5.4.11 Maintenance . 56
6 Information for use . 57
6.1 Warning devices . 57
6.2 Marking . 57
6.3 Instruction handbook . 59
2
---------------------- Page: 4 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
Annex A (normative) Determination of maximum tool spindle speeds . 63
Annex B (normative) Rigidity test for pressure pads, hand protectors and guiding steadies . 68
B.1 Pressure pads . 68
B.1.1 Fence pressure pads . 68
B.1.2 Table pressure pads . 69
B.1.3 Measuring equipment . 71
B.1.4 Test and test requirements. 71
B.1.5 Measuring conditions . 71
B.2 Adjustable guard (Hand protector) and guiding steady . 71
B.2.1 Adjustable guard . 71
B.2.2 Guiding steady . 72
B.2.3 Measuring equipment . 73
B.2.4 Test . 73
B.2.5 Measuring conditions . 74
Annex C (normative) Stability test for displaceable machines . 75
Annex D (informative) Use of well tried components . 76
Annex E (normative) Brake tests . 77
E.1 Conditions for all tests . 77
E.2 Tests . 77
E.2.1 Un-braked run-down time . 77
E.2.2 Run-up time . 77
E.2.3 Braked run-down time . 77
Annex F (normative) Use of electronic components . 79
F.1 General . 79
F.2 SRECS . 79
F.2.1 Components, hardware . 79
F.2.2 Safety related software . 80
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of UE Directive 98/37/EC . 82
Annex ZB (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC" . 85
Bibliography . 89
3
---------------------- Page: 5 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
Foreword
This document (EN 848-1:2007+A1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the
latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1, approved by CEN on 2009-10-03 and Corrigendum 1, issued by CEN
on 2008-11-26.
This document supersedes !EN 848-1:2007".
The start and finish of text introduced or altered by amendment is indicated in the text by tags!"͘
The modifications of the related CEN Corrigendum have been implemented at the appropriate places in the
Ϳ
ϭ
text and are indicated by the tags˜ ™͘
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the !Machinery Directives".
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
Organisation contributing to the preparation of this document include the European Association of
Manufacturer of Woodworking Machines "EUMABOIS".
The European Standards produced by CEN/TC 142 are particular to woodworking machines and compliment
the relevant A and B standards on the subject of general safety (see introduction of EN ISO 12100-1:2003 for
a description of A, B and C standards).
!EN 848 Safety of woodworking machines — One side moulding machines with rotating tool consists of the
following parts:
Part 1: Single spindle vertical moulding machines
Part 2: Single spindle hand fed/integrated fed routing machines
Part 3: Numerically controlled (NC) boring and routing machines"
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
)
1
Applicable to the French version.
4
---------------------- Page: 6 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
Introduction
This document has been prepared to be a harmonised standard to provide one means of conforming to the
essential safety requirements of the Machinery Directive, and associated EFTA Regulations.
This document is a type C standard as stated in EN 12100-1:2003.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of other standards, for machines that
have been designed and built in accordance with the requirements of the provisions of this type C standard.
The requirements of this document are directed to manufacturers and their authorised representatives of
single spindle vertical moulding machines. It is also useful for designers.
This document also includes provisions and examples of information to be provided by the manufacturer to
the user.
Common requirements for tooling are given in EN 847-1:2005, EN 847-2:2001 and EN 847-3:2004.
5
---------------------- Page: 7 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
1 Scope
This document !specifies all significant" hazards, hazardous situations and events as listed in Clause 4
which are relevant to stationary and displaceable hand fed single spindle vertical moulding machines (with or
without demountable power feed unit), herein after referred to as "machines", designed to cut solid wood, chip
board, fibreboard, plywood and also these materials if they are covered with plastic laminate or edgings when
they are used as intended and under the conditions foreseen by the manufacturer.
NOTE 1 For the definition of stationary and displaceable machine see 3.2.17 and 3.2.18.
This document does not apply to:
a) machines equipped with outboard bearings;
b) machines equipped with powered movements of front extension table and/or tenoning travelling table;
c) hand held woodworking machines or any adaptation permitting their use in a different mode, i.e. bench
mounting;
NOTE 2 Hand-held motor-operated electric tools are dealt with in EN 60745-1:2003 together with EN 60745-2-17:2003.
d) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a
stationary position, capable of being lifted by one person by hand. The bench can also be an integrated
part of the machine if it consists of hinged legs which can be extended down;
NOTE 3 Transportable motor-operated electric tools are dealt with in EN 61029-1:2000 together with
!EN 61029-2-8:2003".
This document is not applicable to hand fed single spindle vertical moulding machines which are
manufactured before the date of its publication as EN.
NOTE 4 Machines covered by this document are listed under A.7 of Annex IV of the Machinery Directive.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
!deleted text"
EN 847-1:2005, Tools for woodworking — Safety requirements — Part 1: Milling tools, circular saw blades
EN 847-2:2001, Tools for woodworking — Safety requirements — Part 2: Requirements for the shank of
shank mounted milling tools
EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators
6
---------------------- Page: 8 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and components —
Hydraulics
EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and components —
Pneumatics
EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up
EN 1088:1995, Safety of machinery — Interlocking devices associated with guards — Principles for design
and selection
EN 1837:1999, Safety of machinery — Integral lighting of machines
EN 50178:1997, Electronic equipment for use in power installations
EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine tools — Part
1: Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine tools — Part
2: Immunity
EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1:2005, modified)
EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)
EN 60529:1991, Degree of protection provided by enclosure (IP code) (IEC 60529:1989)
!EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, auditory and tactile signals (IEC 61310-1:2007)"
EN 61496-1:2004, Safety of machinery — Electro sensitive protective equipment — Part 1: General
requirements and tests (IEC 61496-1:2004, modified)
EN 61508-3:2001, Functional safety of electrical/electronic/programmable electronic safety related systems —
Part 3: Software requirements (IEC 61508-3:1998 + Corrigendum 1999)
EN 62061:2005, Safety of machinery — Functional safety of safety-related electrical, electronic and
programmable control systems (IEC 62061:2005)
EN ISO 3743-1:1995, Acoustics — Determination of sound power levels of noise sources — Engineering
methods for small movable sources in reverberant fields — Part 1: Comparison method for hard-walled test
rooms (ISO 3743-1:1994)
7
---------------------- Page: 9 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
EN ISO 3743-2:1996, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Engineering methods for small, movable sources in reverberant fields — Part 1: Methods for
special reverberation test rooms (ISO 3743-2:1994)
EN ISO 3744:1995, Acoustics — Determination of sound power levels of noise sources using sound pressure
— Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994)
EN ISO 3745:2003, Acoustics — Determination of sound power levels of noise sources using sound pressure
— Precision methods for anechoic and semi-anechoic rooms (ISO 3745:2003)
EN ISO 3746:1995, Acoustics — Determination of sound power levels of noise sources using sound pressure
— Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995)
EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 9614-1:1995, Acoustics — Determination of sound power levels of noise sources using sound
intensity — Part 1: Measurement at discreet points (ISO 9614-1:1993)
EN ISO 11202:1995, Acoustics — Noise emitted by machinery and equipment — Measurement method of
emission sound pressure levels at a work station and at other specified positions — Survey method in situ
(ISO 11202:1995)
EN ISO 11202:1995/AC:1997, Acoustics — Noise emitted by machinery and equipment — Measurement
method of emission sound pressure levels at a work station and at other specified positions — Survey method
in situ (ISO 11202:1995/Cor.1:1997)
EN ISO 11204:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Method requiring environmental
corrections (ISO 11204:1995)
EN ISO 11204:1995/AC:1997, Acoustics — Noise emitted by machinery and equipment — Measurement of
emission sound pressure levels at a work station and at other specified positions — Method requiring
environmental corrections (ISO 11204:1995/Cor.1:1997)
EN ISO 11688-1:1998, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 11688-1:1998/AC:1998, Acoustics — Recommended practice for the design of low-noise machinery
and equipment — Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)
!EN ISO 13849-1:2008", Safety of machinery — Safety-related parts of control systems — Part 1:
General principles for design (ISO 13849-1:2006)
!EN ISO 13849-2:2008", Safety of machinery — Safety-related parts of control systems — Part 2:
Validation (ISO 13849-2:2003)
EN ISO 13850:2006, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)
!EN ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2008)"
8
---------------------- Page: 10 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
ISO 7009:1983, Woodworking machines — Single spindle moulding machines — Nomenclature and
acceptance conditions
ISO 7960:1995, Airborne noise emitted by machine tools — Operating conditions for woodworking machines
3 Terms and definitions
3.1 General
For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following
apply.
3.2 Definitions
3.2.1
single spindle vertical moulding machine
hand fed machine fitted with a single vertical spindle (fixed or removable) the position of which is fixed during
machining and a horizontal table, all or part of which are fixed during operation. The spindle passes through
the table and its drive motor is situated beneath the table. The machine may have any of the following
features:
a) the facility for the spindle to be vertically adjustable relative to the table;
b) the facility to tilt the spindle;
c) the facility for fitting an additional manually operated tenoning travelling table;
d) the facility for the glass bead recovery;
e) the facility for an adjustable table insert
3.2.2
straight work
shaping of a work-piece with one face in contact with the table and a second with the fence, and where the
work starts at one end of the work-piece and continues through to the other end (see Figure 1)
Figure 1 — Example of straight work
9
---------------------- Page: 11 ----------------------
SIST EN 848-1:2007+A1:2010
EN 848-1:2007+A1:2009 (E)
3.2.3
curved work
machining of a curve on a work-piece by having one side in contact with the table (or if held in a jig with the jig
in contact with the table) and the other in contact with the vertical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.