kSIST FprEN 507:2026

SLOVENSKI STANDARD
oSIST prEN 507:2025
01-julij-2025
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte
proizvode iz aluminijske pločevine
Roofing and cladding products from metal sheet - Specification for fully supported
products of aluminium sheet
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für
vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de
couverture en tôle d'aluminium totalement supportés
Ta slovenski standard je istoveten z: prEN 507
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
oSIST prEN 507:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 507:2025
oSIST prEN 507:2025
DRAFT
EUROPEAN STANDARD
prEN 507
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2025
ICS 91.060.20 Will supersede EN 507:2019
English Version
Roofing and cladding products from metal sheet -
Specification for fully supported products of aluminium
sheet
Produits de couverture et bardage en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les produits de couverture en tôle Metallblech - Festlegungen für vollflächig unterstützte
d'aluminium totalement supportés Bedachungselemente aus Aluminiumblech
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 128.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 507:2025 E
worldwide for CEN national Members.

oSIST prEN 507:2025
prEN 507:2025 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, symbols and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Symbols and abbreviations . 6
4 Requirements . 7
4.1 General. 7
4.2 Materials . 7
4.2.1 Aluminium . 7
4.2.2 Organic coatings . 8
4.2.3 Anodizing . 9
4.3 Products . 9
4.3.1 Flat products . 9
4.3.2 Formed (prefabricated) products . 9
4.3.3 Safety in case of fire. 9
5 Sampling and test methods . 10
5.1 Flat products . 10
5.2 Formed (prefabricated) products . 10
5.2.1 Sampling . 10
5.2.2 Testing . 10
6 Designation . 10
7 Marking, labelling and packaging . 10
7.1 Marking and labelling . 10
7.2 Packaging and any special ordering conditions . 11
7.3 Transport, storage and handling . 11
Bibliography . 12

oSIST prEN 507:2025
prEN 507:2025 (E)
European foreword
This document (prEN 507:2025) has been prepared by Technical Committee CEN/TC 128 “Roof
covering products for discontinuous laying and products for wall cladding”, the secretariat of which is
held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 507:2019.
prEN 507:2025 includes the following significant technical changes with respect to EN 507:2019:
The list of aluminium alloys suitable for roofing and cladding products has been extended.
These changes or additions can be found in the following sections: 4.2.1.
oSIST prEN 507:2025
prEN 507:2025 (E)
Introduction
Figure 1 indicates the position of this document in the CEN framework of standards concerning roofing
and cladding products of metal sheet.

Roofing and cladding products
of metal sheet
Self supporting   Fully supported products
products
EN 14783
EN 14782
Zinc  Stainless steel  Copper  Steel  Aluminium
EN 501 EN 502 EN 504 EN 505 EN 507

References regarding
Materials
Quality
assurance
Figure 1 — Framework of standards
In this document the performance of the product has been defined in terms of a number of type tests.
The performance of a roof or cladding constructed with these products depends not only on the
properties of the product as it is required by this document, but also on the design, construction and
performance of the roof or the cladding as a whole in relation to the environment and conditions of use.
Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn,
folded, roll-formed without difficulty within the given limits of the properties listed in the respective
material specifications.
Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but
minimum bend radius, design of forming tools, process temperature etc are chosen according to
material properties.
oSIST prEN 507:2025
prEN 507:2025 (E)
1 Scope
This document specifies requirements for roofing and cladding products used for assembly into
coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without
additional surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together
with requirements for the materials from which the products can be manufactured. It is intended to be
used either by manufacturers to ensure that their products comply with the requirements or by
purchasers to verify that the products comply before they are despatched from the factory. It specifies
the requirements for products which enable them to meet all normal service conditions. Products can
be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications
(e.g. standing seam roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products
made of aluminium sheets. No requirements for supporting construction, design of roof system and
execution of connections and flashings are included.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2:—.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 485-1, Aluminium and aluminium alloys — Sheet, strip and plate — Part 1: Technical conditions for
inspection and delivery
EN
...