SIST EN 302 217-2-2 V2.2.1:2014

Harmonized European Standard
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2-2: Digital systems operating in frequency bands where
frequency co-ordination is applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

2 ETSI EN 302 217-2-2 V2.2.1 (2014-04)

Reference
REN/ATTM-04025
Keywords
antenna, DFRS, digital, DRRS, FWA, point-to-
point, radio, regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 7
1 Scope . 8
1.1 General background . 8
1.2 Spectral efficiency classes . 8
1.3 System alternatives . 9
1.4 Channel arrangements and utilization . 10
1.5 Payload flexibility . 10
1.6 Document structure . 11
2 References . 11
2.1 Normative references . 12
2.2 Informative references . 12
3 Definitions, symbols and abbreviations . 16
3.1 Definitions . 16
3.2 Symbols . 16
3.3 Abbreviations . 16
4 Technical requirements specifications . 16
4.0 System identification and traffic loading . 16
4.1 Environmental profile . 17
4.2 Transmitter requirements . 18
4.2.1 Transmitter power and power tolerance . 18
4.2.1.1 Maximum power . 18
4.2.1.2 Transmitter power tolerance. 18
4.2.2 Transmitter power and frequency control . 19
4.2.2.1 Transmitter Power Control (ATPC and RTPC) . 19
4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 19
4.2.2.1.2 Remote Transmit Power Control (RTPC) . 19
4.2.2.2 Remote Frequency Control (RFC) . 19
4.2.3 Void . 19
4.2.4 Radio Frequency (RF) spectrum mask. 20
4.2.4.1 Limits background . 20
4.2.4.2 Limits . 23
4.2.4.2.1 Unified masks . 23
4.2.4.2.2 Other alternative and system specific masks options . 35
4.2.5 Discrete CW components exceeding the spectrum mask limit . 35
4.2.5.1 Discrete CW components at the symbol rate . 35
4.2.5.2 Other discrete CW components exceeding the spectrum mask limit . 35
4.2.6 Spurious emissions - external . 37
4.2.7 Dynamic Change of Modulation Order . 37
4.2.8 Radio frequency tolerance . 37
4.3 Receiver requirements . 37
4.3.1 Spurious emissions - external . 38
4.3.2 BER as a function of receiver input signal level RSL . 38
4.3.3 Co-channel "external" and adjacent channel interference sensitivity . 38
4.3.4 CW spurious interference . 39
4.4 Antenna directional requirements . 39
4.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 40
4.4.2 Antenna gain . 40
4.4.3 Antenna Cross-Polar Discrimination (XPD) . 40
5 Testing for compliance with technical requirements . 40
5.1 Environmental and other conditions for testing . 40
5.1.1 Environmental conditions . 40
ETSI
4 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
5.1.2 Test interpretation and measurement uncertainty . 40
5.1.3 Other basic conditions . 41
5.2 Essential radio test suites for the transmitter . 41
5.2.1 Transmitter power and power tolerance . 42
5.2.2 Transmitter power and frequency control . 43
5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 43
5.2.2.1.1 ATPC . 43
5.2.2.1.2 RTPC . 43
5.2.2.1.3 Remote Frequency Control (RFC). 43
5.2.3 Void . 43
5.2.4 RF spectrum mask . 43
5.2.5 Discrete CW components exceeding the spectrum mask limit . 44
5.2.6 Spurious emissions - external . 44
5.2.7 Dynamic Change of Modulation Order . 44
5.2.8 Radio frequency tolerance . 44
5.3 Essential radio test suites for the receiver . 45
5.3.1 Spurious emissions - external . 45
5.3.2 BER as a function of receiver input signal level (RSL) . 46
5.3.3 Co-channel "external" and adjacent channel interference sensitivity . 46
5.3.4 CW spurious interference . 46
5.4 Additional essential antenna test suites for systems with integral antenna. 46
5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 46
5.4.2 Antenna gain . 46
5.4.3 Antenna Cross-Polar Discrimination (XPD) . 46
Annex A (normative): Frequency bands from 1,4 GHz to 2,7 GHz . 47
A.1 Introduction . 47
A.2 General characteristics . 47
A.2.1 Frequency characteristics and channel arrangements . 47
A.2.2 Transmission capacities . 48
A.3 Transmitter . 48
A.3.1 General requirements . 48
A.3.2 RF spectrum masks options . 49
A.4 Receiver . 49
A.4.1 General requirements . 49
A.4.2 BER as a function of receiver input signal level (RSL) . 50
A.4.3 Co-channel "external" and adjacent channels interference sensitivity . 50
Annex B (normative): Frequency bands from 3 GHz to 11 GHz (channel separation up to
30 MHz and 56/60 MHz) . 52
B.1 Introduction . 52
B.2 General characteristics . 52
B.2.1 Frequency characteristics and channel arrangements . 52
B.2.2 Transmission capacities . 53
B.3 Transmitter . 54
B.3.1 General requirements . 54
B.3.2 RF spectrum masks options . 54
B.4 Receiver . 55
B.4.1 General requirements . 55
B.4.2 BER as a function of Receiver input Signal Level (RSL) . 55
B.4.3 Co-channel "external" and adjacent channel interference sensitivity . 57
Annex C (normative): Frequency bands from 3 GHz to 11 GHz (channel separation
40 MHz) . 58
C.1 Introduction . 58
C.2 General characteristics . 58
ETSI
5 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
C.2.1 Frequency characteristics and channel arrangements . 58
C.2.2 Transmission capacities . 58
C.3 Transmitter . 59
C.3.1 General requirements . 59
C.3.2 RF spectrum masks . 59
C.4 Receiver . 60
C.4.1 General requirements . 60
C.4.2 BER as a function of Receiver input Signal Level (RSL) . 60
C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 61
Annex D (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 62
D.1 Introduction . 62
D.2 General characteristics . 62
D.2.1 Frequency characteristics and channel arrangements . 62
D.2.2 Transmission capacities . 63
D.3 Transmitter . 63
D.3.1 General requirements . 63
D.3.2 RF spectrum masks options . 64
D.4 Receiver . 65
D.4.1 General requirements . 65
D.4.2 BER as a function of Receiver input Signal Level (RSL) . 65
D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 67
Annex E (normative): Frequency bands from 23 GHz to 55 GHz . 69
E.1 Introduction . 69
E.2 General characteristics . 69
E.2.1 Frequency characteristics and channel arrangements . 69
E.2.2 Transmission capacities . 70
E.3 Transmitter . 70
E.3.1 General requirements . 70
E.3.2 RF spectrum masks options . 71
E.3.2.1 Frequency bands 23 GHz to 42 GHz . 71
E.3.2.2 Frequency bands 50 GHz to 55 GHz . 72
E.4 Receiver . 72
E.4.1 General requirements . 72
E.4.2 BER as a function of Receiver input Signal Level (RSL) . 73
E.4.2.1 Systems in bands from 23 GHz to 42 GHz . 74
E.4.2.2 Systems in bands from 50 GHz to 55 GHz . 76
E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 77
Annex Ea (normative): Frequency bands from 71 GHz to 86 GHz . 78
Ea.1 Introduction . 78
Ea.2 General characteristics . 78
Ea.2.1 Frequency characteristics and channel arrangements . 78
Ea.2.2 Transmission capacities . 79
Ea.3 Transmitter . 80
Ea.3.1 General requirements . 80
Ea.3.2 RF spectrum masks . 80
Ea.4 Receiver . 80
Ea.4.1 General requirements . 80
Ea.4.2 BER as a function of Receiver input Signal Level (RSL) . 80
Ea.4.3 Co-channel "external" and adjacent channel interference sensitivity . 82
ETSI
6 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 84
F.1 Introduction . 84
F.2 General characteristics . 84
F.2.1 Frequency characteristics and channel arrangements . 84
F.2.2 Transmission capacities . 84
F.3 System parameters . 87
F.3.1 Transmitter . 87
F.3.2 Receiver . 87
F.3.3 FER as a function of BER . 87
Annex G (normative): Test report in relation to flexible systems applications . 89
G.1 Wide radio-frequency band covering units . 89
G.2 Multirate/multiformat equipment . 91
G.2.1 Generic required tests in the test report . 91
G.2.2 Reduced required tests in the test report . 91
G.2.2.1 Reduced transmitter tests . 91
G.2.2.2 Reduced receiver tests . 92
G.2.3 Bandwidth adaptive test set requirements . 93
G.3 BER measurement in a SDH or Ethernet multi-interfaces, multi-channels system . 93
G.3.1 Case 1: multi-interfaces/single channel or multi-interfaces/two-channels systems where each interface
payload is transmitted on one channel only . 94
G.3.2 Case 2: single interface/two-channels system . 94
G.3.3 Case 3: multi-interfaces/two-channels system where each payload interface is transmitted on both
channels . 94
Annex H (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 95
Annex I (informative): Impact of power control (ATPC and/or RTPC), mixed-mode and
bandwidth adaptive operation on spectrum mask and link design
requirements. 97
I.0 General Background for, ATPC, RTPC and mixed mode operation . 97
I.1 ATPC and RTPC implementation background . 97
I.2 Mixed-mode operation impact . 99
I.2.1 Basic concepts . 99
I.3 Bandwidth adaptive operation impact . 100
I.3.1 Basic concepts . 100
I.3.2 Bandwidth (channel) occupancy . 100
I.4 Impact on frequency co-ordination . 100
I.5 Impact on article 3.2 "essential" parameters and operating conditions . 102
Annex J (informative): Typical interference sensitivity behaviour for frequency planning
purpose . 104
Annex K (informative): Bibliography . 105
Annex L (informative): Change History . 106
History . 107

ETSI
7 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals,
Transmission and Multiplexing (ATTM).
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.64].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [1].
See article 5.1 of Directive 1999/5/EC [1] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [1] are summarized in annex H.
The present document is part 2, sub-part 2 of a multi-part deliverable covering Fixed Radio Systems; Characteristics
and requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [6].

National transposition dates
Date of adoption of this EN: 26 March 2014
Date of latest announcement of this EN (doa): 30 June 2014
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2014
Date of withdrawal of any conflicting National Standard (dow): 31 December 2015

Introduction
The EN 302 217 series has been produced in order to rationalize a large number of previous ETSI ENs dealing with
equipment and antennas for Point-to-Point (P-P) Fixed Service applications. For more details, see foreword in the
EN 302 217-1 [6].
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is described in EG 201 399 [i.24].
Figure 1: Void
ETSI
8 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
1 Scope
1.1 General background
The present document specifies the essential requirements for point-to-point Digital Fixed Radio Systems (DFRS)
operating in frequency division full duplex (FDD) in frequency bands, where co-ordinated link-by-link frequency
planning is applied. It is intended to cover the provisions of the R&TTE Directive [1] regarding article 3.2, which states
that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio
communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
For the correct understanding and application of the requirements in the present document, the definitions summarized
in EN 302 217-1 [6] are also relevant.
1.2 Spectral efficiency classes
As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment
classes are here defined. They are based on typical modulation formats and limited by a "minimum Radio Interface
Capacity density" (Mbit/s/MHz) shown in table 0. Radio Interface Capacity (RIC) is defined in EN 302 217-1 [6].
The minimum RIC density figures in table 0 are valid only for systems operating on the most common channel
separation (CS) equal or higher than 1,75 MHz and taking into account that for channel separations "about" 14 MHz
(i.e. from 13,75 MHz to 15,0 MHz), "about" 28 MHz (i.e. from 27,5 MHz to 30 MHz), "about" 56 MHz (i.e. from
55 MHz to 60 MHz) and "about" 112 MHz (i.e. 110 MHz or 112 MHz) the RIC density of actual systems is evaluated
only over the "nominal" 14 MHz, 28 MHz, 56 MHz and 112 MHz channel width.
Minimum RIC figures for some systems operating on 40 MHz channel separation, with RIC density lower than the
minimum requirement in table 0, are defined only in annexes C and Ea. For the special cases of sub-STM-0 capacities
(defined in Recommendation ITU-T G.708 [i.63], annex D), alternative minimum RIC figures are not defined.
ETSI
9 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
Table 0: Spectral efficiency classes and their minimum RIC density
Reference Spectral Minimum Description
modulation efficiency RIC density
index class (Mbit/s/MHz)
(see note)
1 1 0,57 Equipment with spectral efficiency based on typical 2-states modulation
scheme (e.g. 2FSK, 2PSK)
2 2 1,14 Equipment with spectral efficiency based on typical 4-states modulation
scheme (e.g. 4FSK, 4QAM)
3 3 1,7 Equipment with spectral efficiency based on typical 8-states modulation
scheme (e.g. 8PSK)
4 4L 2,28 Equipment with spectral efficiency based on typical 16-states modulation
scheme (e.g. 16QAM, 16APSK)
5 4H 3,5 Equipment with spectral efficiency based on typical 32-states modulation
scheme (e.g. 32QAM, 32APSK)
6 5L 4,2 Equipment with spectral efficiency based on typical 64-states modulation
scheme (e.g. 64QAM)
7 5H 4,9 Equipment with spectral efficiency based on typical 128-states modulation
scheme (e.g. 128QAM)
8 6L 5,6 Equipment with spectral efficiency based on typical 256-states modulation
scheme (e.g. 256QAM)
9 6H 6,3 Equipment with spectral efficiency based on typical 512-states modulation
scheme (e.g. 512QAM)
10 7 7 Equipment with spectral efficiency based on typical 1 024-states
modulation scheme (e.g. 1024QAM)
11 8 7,7 Equipment with spectral efficiency based on typical 2 048-states
modulation scheme (e.g. 2048QAM)
NOTE: When defining the minimum RIC for actual channel separations, for simplicity, it will be rounded to the
suitably closer integer Mbit/s.

All classes up to class 4H, for any CS, and classes 5L, 5H, 6L, 6H, 7 and 8, for CS < 27,5 MHz, are intended suitable
for ACCP operation and, in principle, whenever appropriate, also expandable to CCDP. Classes 5L, 5H, 6L, 6H, 7 and
8, only for CS ≥ 27,5 MHz, are further subdivided in two sub-classes:
• subClass A: classes 5LA, 5HA, 6LA, 6HA, 7A and 8A are intended suitable, on the same route, for cross-polar
adjacent channel (ACAP) operation only (see figure 2a).
• subClass B: classes 5LB, 5HB, 6LB, 6HB, 7B and 8B are suitable, on the same route, for ACCP operation and,
in principle, whenever appropriate, also expandable to CCDP (see figure 2a).
The above classes are for system identification only and will not imply any constraint to the actual modulation format,
provided that all the requirements of the selected class in the relevant parts of EN 302 217 series are met.
1.3 System alternatives
In order to (technically) cover different market and network requirements, with an appropriate balance of performance
to cost and effective and appropriate use of the radio spectrum, the present document, together with
EN 302 217-4-2 [8], offers a number of system types and antennas alternatives, for selection by administrations,
operators and manufacturers dependent on the desired use of the radio spectrum and network/market requirements;
those options include:
• channel separation alternatives (as provided by the relevant CEPT or Recommendation ITU-R);
• spectral efficiency class alternatives (different modulation formats provided in radio equipment standards) as
defined in clause 1.2; actual equipment may operate within one spectral efficiency class only
(Single-mode) or within multiple classes, either with static pre-selection of the class (Preset-mode) or with
dynamic variation of capacity according the propagation conditions (Mixed-mode) (see note);
• antenna directivity class alternatives (for different network requirements).
NOTE: Single- mode, Preset-mode and Mixed-mode systems are defined in clause 3.1 of EN 302 217-1 [6];
additional information on Mixed-mode systems may be found in annex I of the present document and in
TR 103 103 [i.35].
ETSI
10 ETSI EN 302 217-2-2 V2.2.1 (2014-04)
1.4 Channel arrangements and utilization
Systems in the scope of the present document are intended to operate only in full frequency division duplex (FDD).
Time division duplex (TDD) applications are not in the scope of the present document.
Unidirectional systems are assumed to be an underequipped FDD system.
From the point of view of the transmission capacity, these systems are defined, in the relevant annexes, on the basis of
their minimum Channel Separation (CS) on the same route, for a given spectral efficiency class, taken into account by
the system design. The possible channel arrangements may be:
• Adjacent Channel Alternate-Polarized (ACAP);
• Adjacent Channel Co-Polarized (ACCP);
• Co-Channel Dual-Polarization (CCDP).
These possible applications and their channel arrangements are shown in figure 2a.
V
V or H
V
H H
ACAP
ACCP
CCDP
Figure 2a: Examples of channel arrangements on the same route
1.5 Payload flexibility
For quick identification of the system, the capacities in tables X.2 (where X = A, B, C, D, E, Ea represents the relevant
annex) are the minimum transmitted RIC required for conformance to the present document; they are based on the
"minimum RIC density" defined in clause 1.2. Only some cases of systems in annex A, due to the smaller channel
separation provided, are (exceptionally) labelled with typical gross bit rate rather than minimum RIC capacity rates.
However, equipment may offer a variety of base band interfaces, e.g. typical hierarchical rates PDH or SDH, ISDN,
Ethernet as well as mixture of these or other standardized interfaces. Mapping/multiplexing of the various base-band
interfaces into common frame(s) suitable for radio transmission may be done using standardized higher hierarchical
frames or other proprietary methods.
NOTE: Information on applicable base-band interfaces can be found in EN 302 217-1 [6].
Tables F.1a through F.1g in annex F summarize the "minimum RIC" considered in the present document and, when
only PDH or SDH interfaces are provided, give the equivalent capacity in term of number of 2,048 Mbit/s streams
provided as multiple or single multiplexed PDH or SDH interfaces. These minimum capacities will be associated to the
relevant channel separation and spectral efficiency classes defined.
Equipment may operate with one single RIC payload rate or with multiple RIC payload rates (multirate systems), either
statically preset (possibly coupled also with preset-mode operation) or, when coupled with mixed-mode operation,
dynamically changing according to the modulation format.
The requirements of the present document apply separately to each transmitter/receiver or single transmitters or
receivers used for combining complex or simple (e.g. space diversity receivers or single transmitters and receivers used
for unidirectional links) fixed radio systems. Systems carrying N × STM-1 (N =
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 2-2: Digital systems operating in frequency bands where frequency co-ordination is applied - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 302 217-2-2 Version 2.2.1SIST EN 302 217-2-2 V2.2.1:2014en01-junij-2014SIST EN 302 217-2-2 V2.2.1:2014SLOVENSKI
STANDARD
Harmonized European Standard SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)2
Reference REN/ATTM-04025 Keywords antenna, DFRS, digital, DRRS, FWA,
point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)3 Contents Intellectual Property Rights . 7 Foreword . 7 Introduction . 7 1 Scope . 8 1.1 General background . 8 1.2 Spectral efficiency classes . 8 1.3 System alternatives . 9 1.4 Channel arrangements and utilization . 10 1.5 Payload flexibility . 10 1.6 Document structure . 11 2 References . 11 2.1 Normative references . 12 2.2 Informative references . 12 3 Definitions, symbols and abbreviations . 16 3.1 Definitions . 16 3.2 Symbols . 16 3.3 Abbreviations . 16 4 Technical requirements specifications . 16 4.0 System identification and traffic loading . 16 4.1 Environmental profile . 17 4.2 Transmitter requirements . 18 4.2.1 Transmitter power and power tolerance . 18 4.2.1.1 Maximum power . 18 4.2.1.2 Transmitter power tolerance. 18 4.2.2 Transmitter power and frequency control . 19 4.2.2.1 Transmitter Power Control (ATPC and RTPC) . 19 4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 19 4.2.2.1.2 Remote Transmit Power Control (RTPC) . 19 4.2.2.2 Remote Frequency Control (RFC) . 19 4.2.3 Void . 19 4.2.4 Radio Frequency (RF) spectrum mask. 20 4.2.4.1 Limits background . 20 4.2.4.2 Limits . 23 4.2.4.2.1 Unified masks . 23 4.2.4.2.2 Other alternative and system specific masks options . 35 4.2.5 Discrete CW components exceeding the spectrum mask limit . 35 4.2.5.1 Discrete CW components at the symbol rate . 35 4.2.5.2 Other discrete CW components exceeding the spectrum mask limit . 35 4.2.6 Spurious emissions - external . 37 4.2.7 Dynamic Change of Modulation Order . 37 4.2.8 Radio frequency tolerance . 37 4.3 Receiver requirements . 37 4.3.1 Spurious emissions - external . 38 4.3.2 BER as a function of receiver input signal level RSL . 38 4.3.3 Co-channel "external" and adjacent channel interference sensitivity . 38 4.3.4 CW spurious interference . 39 4.4 Antenna directional requirements . 39 4.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 40 4.4.2 Antenna gain . 40 4.4.3 Antenna Cross-Polar Discrimination (XPD) . 40 5 Testing for compliance with technical requirements . 40 5.1 Environmental and other conditions for testing . 40 5.1.1 Environmental conditions . 40 SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)4 5.1.2 Test interpretation and measurement uncertainty . 40 5.1.3 Other basic conditions . 41 5.2 Essential radio test suites for the transmitter . 41 5.2.1 Transmitter power and power tolerance . 42 5.2.2 Transmitter power and frequency control . 43 5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 43 5.2.2.1.1 ATPC . 43 5.2.2.1.2 RTPC . 43 5.2.2.1.3 Remote Frequency Control (RFC). 43 5.2.3 Void . 43 5.2.4 RF spectrum mask . 43 5.2.5 Discrete CW components exceeding the spectrum mask limit . 44 5.2.6 Spurious emissions - external . 44 5.2.7 Dynamic Change of Modulation Order . 44 5.2.8 Radio frequency tolerance . 44 5.3 Essential radio test suites for the receiver . 45 5.3.1 Spurious emissions - external . 45 5.3.2 BER as a function of receiver input signal level (RSL) . 46 5.3.3 Co-channel "external" and adjacent channel interference sensitivity . 46 5.3.4 CW spurious interference . 46 5.4 Additional essential antenna test suites for systems with integral antenna. 46 5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 46 5.4.2 Antenna gain . 46 5.4.3 Antenna Cross-Polar Discrimination (XPD) . 46 Annex A (normative): Frequency bands from 1,4 GHz to 2,7 GHz . 47 A.1 Introduction . 47 A.2 General characteristics . 47 A.2.1 Frequency characteristics and channel arrangements . 47 A.2.2 Transmission capacities . 48 A.3 Transmitter . 48 A.3.1 General requirements . 48 A.3.2 RF spectrum masks options . 49 A.4 Receiver . 49 A.4.1 General requirements . 49 A.4.2 BER as a function of receiver input signal level (RSL) . 50 A.4.3 Co-channel "external" and adjacent channels interference sensitivity . 50 Annex B (normative): Frequency bands from 3 GHz to 11 GHz
(channel separation up to 30 MHz and 56/60 MHz) . 52 B.1 Introduction . 52 B.2 General characteristics . 52 B.2.1 Frequency characteristics and channel arrangements . 52 B.2.2 Transmission capacities . 53 B.3 Transmitter . 54 B.3.1 General requirements . 54 B.3.2 RF spectrum masks options . 54 B.4 Receiver . 55 B.4.1 General requirements . 55 B.4.2 BER as a function of Receiver input Signal Level (RSL) . 55 B.4.3 Co-channel "external" and adjacent channel interference sensitivity . 57 Annex C (normative): Frequency bands from 3 GHz to 11 GHz (channel separation 40 MHz) . 58 C.1 Introduction . 58 C.2 General characteristics . 58 SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)5 C.2.1 Frequency characteristics and channel arrangements . 58 C.2.2 Transmission capacities . 58 C.3 Transmitter . 59 C.3.1 General requirements . 59 C.3.2 RF spectrum masks . 59 C.4 Receiver . 60 C.4.1 General requirements . 60 C.4.2 BER as a function of Receiver input Signal Level (RSL) . 60 C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 61 Annex D (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 62 D.1 Introduction . 62 D.2 General characteristics . 62 D.2.1 Frequency characteristics and channel arrangements . 62 D.2.2 Transmission capacities . 63 D.3 Transmitter . 63 D.3.1 General requirements . 63 D.3.2 RF spectrum masks options . 64 D.4 Receiver . 65 D.4.1 General requirements . 65 D.4.2 BER as a function of Receiver input Signal Level (RSL) . 65 D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 67 Annex E (normative): Frequency bands from 23 GHz to 55 GHz . 69 E.1 Introduction . 69 E.2 General characteristics . 69 E.2.1 Frequency characteristics and channel arrangements . 69 E.2.2 Transmission capacities . 70 E.3 Transmitter . 70 E.3.1 General requirements . 70 E.3.2 RF spectrum masks options . 71 E.3.2.1 Frequency bands 23 GHz to 42 GHz . 71 E.3.2.2 Frequency bands 50 GHz to 55 GHz . 72 E.4 Receiver . 72 E.4.1 General requirements . 72 E.4.2 BER as a function of Receiver input Signal Level (RSL) . 73 E.4.2.1 Systems in bands from 23 GHz to 42 GHz . 74 E.4.2.2 Systems in bands from 50 GHz to 55 GHz . 76 E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 77 Annex Ea (normative): Frequency bands from 71 GHz to 86 GHz . 78 Ea.1 Introduction . 78 Ea.2 General characteristics . 78 Ea.2.1 Frequency characteristics and channel arrangements . 78 Ea.2.2 Transmission capacities . 79 Ea.3 Transmitter . 80 Ea.3.1 General requirements . 80 Ea.3.2 RF spectrum masks . 80 Ea.4 Receiver . 80 Ea.4.1 General requirements . 80 Ea.4.2 BER as a function of Receiver input Signal Level (RSL) . 80 Ea.4.3 Co-channel "external" and adjacent channel interference sensitivity . 82 SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)6 Annex F (normative): Definition of equivalent data rates for packet data, PDH/SDH and other signals on the traffic interface. 84 F.1 Introduction . 84 F.2 General characteristics . 84 F.2.1 Frequency characteristics and channel arrangements . 84 F.2.2 Transmission capacities . 84 F.3 System parameters . 87 F.3.1 Transmitter . 87 F.3.2 Receiver . 87 F.3.3 FER as a function of BER . 87 Annex G (normative): Test report in relation to flexible systems applications . 89 G.1 Wide radio-frequency band covering units . 89 G.2 Multirate/multiformat equipment . 91 G.2.1 Generic required tests in the test report . 91 G.2.2 Reduced required tests in the test report . 91 G.2.2.1 Reduced transmitter tests . 91 G.2.2.2 Reduced receiver tests . 92 G.2.3 Bandwidth adaptive test set requirements . 93 G.3 BER measurement in a SDH or Ethernet multi-interfaces, multi-channels system . 93 G.3.1 Case 1: multi-interfaces/single channel or multi-interfaces/two-channels systems where each interface payload is transmitted on one channel only . 94 G.3.2 Case 2: single interface/two-channels system . 94 G.3.3 Case 3: multi-interfaces/two-channels system where each payload interface is transmitted on both channels . 94 Annex H (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 95 Annex I (informative): Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation on spectrum mask and link design requirements. 97 I.0 General Background for, ATPC, RTPC and mixed mode operation . 97 I.1 ATPC and RTPC implementation background . 97 I.2 Mixed-mode operation impact . 99 I.2.1 Basic concepts . 99 I.3 Bandwidth adaptive operation impact . 100 I.3.1 Basic concepts . 100 I.3.2 Bandwidth (channel) occupancy . 100 I.4 Impact on frequency co-ordination . 100 I.5 Impact on article 3.2 "essential" parameters and operating conditions . 102 Annex J (informative): Typical interference sensitivity behaviour for frequency planning purpose . 104 Annex K (informative): Bibliography . 105 Annex L (informative): Change History . 106 History . 107
ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.64]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [1]. See article 5.1 of Directive 1999/5/EC [1] for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [1] are summarized in annex H. The present document is part 2, sub-part 2 of a multi-part deliverable covering Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [6].
National transposition dates Date of adoption of this EN: 26 March 2014 Date of latest announcement of this EN (doa): 30 June 2014 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2014 Date of withdrawal of any conflicting National Standard (dow): 31 December 2015
Introduction The EN 302 217 series has been produced in order to rationalize a large number of previous ETSI ENs dealing with equipment and antennas for Point-to-Point (P-P) Fixed Service applications. For more details, see foreword in the EN 302 217-1 [6]. The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular structure is described in EG 201 399 [i.24]. Figure 1: Void SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)8 1 Scope 1.1 General background The present document specifies the essential requirements for point-to-point Digital Fixed Radio Systems (DFRS) operating in frequency division full duplex (FDD) in frequency bands, where co-ordinated link-by-link frequency planning is applied. It is intended to cover the provisions of the R&TTE Directive [1] regarding article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. For the correct understanding and application of the requirements in the present document, the definitions summarized in EN 302 217-1 [6] are also relevant. 1.2 Spectral efficiency classes As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment classes are here defined. They are based on typical modulation formats and limited by a "minimum Radio Interface Capacity density" (Mbit/s/MHz) shown in table 0. Radio Interface Capacity (RIC) is defined in EN 302 217-1 [6]. The minimum RIC density figures in table 0 are valid only for systems operating on the most common channel separation (CS) equal or higher than 1,75 MHz and taking into account that for channel separations "about" 14 MHz (i.e. from 13,75 MHz to 15,0 MHz), "about" 28 MHz (i.e. from 27,5 MHz to 30 MHz), "about" 56 MHz (i.e. from 55 MHz to 60 MHz) and "about" 112 MHz (i.e. 110 MHz or 112 MHz) the RIC density of actual systems is evaluated only over the "nominal" 14 MHz, 28 MHz, 56 MHz and 112 MHz channel width. Minimum RIC figures for some systems operating on 40 MHz channel separation, with RIC density lower than the minimum requirement in table 0, are defined only in annexes C and Ea. For the special cases of sub-STM-0 capacities (defined in Recommendation ITU-T G.708 [i.63], annex D), alternative minimum RIC figures are not defined. SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)9 Table 0: Spectral efficiency classes and their minimum RIC density Reference modulation index Spectral efficiency class Minimum
RIC density (Mbit/s/MHz) (see note) Description 1 1 0,57 Equipment with spectral efficiency based on typical 2-states modulation scheme (e.g. 2FSK, 2PSK) 2 2 1,14 Equipment with spectral efficiency based on typical 4-states modulation scheme (e.g. 4FSK, 4QAM) 3 3 1,7 Equipment with spectral efficiency based on typical 8-states modulation scheme (e.g. 8PSK) 4 4L 2,28 Equipment with spectral efficiency based on typical 16-states modulation scheme (e.g. 16QAM, 16APSK) 5 4H 3,5 Equipment with spectral efficiency based on typical 32-states modulation scheme (e.g. 32QAM, 32APSK) 6 5L 4,2 Equipment with spectral efficiency based on typical 64-states modulation scheme (e.g. 64QAM) 7 5H 4,9 Equipment with spectral efficiency based on typical 128-states modulation scheme (e.g. 128QAM) 8 6L 5,6 Equipment with spectral efficiency based on typical 256-states modulation scheme (e.g. 256QAM) 9 6H 6,3 Equipment with spectral efficiency based on typical 512-states modulation scheme (e.g. 512QAM) 10 7 7 Equipment with spectral efficiency based on typical 1 024-states modulation scheme (e.g. 1024QAM) 11 8 7,7 Equipment with spectral efficiency based on typical 2 048-states modulation scheme (e.g. 2048QAM) NOTE: When defining the minimum RIC for actual channel separations, for simplicity, it will be rounded to the suitably closer integer Mbit/s.
All classes up to class 4H, for any CS, and classes 5L, 5H, 6L, 6H, 7 and 8, for CS < 27,5 MHz, are intended suitable for ACCP operation and, in principle, whenever appropriate, also expandable to CCDP. Classes 5L, 5H, 6L, 6H, 7 and 8, only for CS ≥ 27,5 MHz, are further subdivided in two sub-classes: • subClass A: classes 5LA, 5HA, 6LA, 6HA, 7A and 8A are intended suitable, on the same route, for cross-polar adjacent channel (ACAP) operation only (see figure 2a). • subClass B: classes 5LB, 5HB, 6LB, 6HB, 7B and 8B are suitable, on the same route, for ACCP operation and, in principle, whenever appropriate, also expandable to CCDP (see figure 2a). The above classes are for system identification only and will not imply any constraint to the actual modulation format, provided that all the requirements of the selected class in the relevant parts of EN 302 217 series are met. 1.3 System alternatives In order to (technically) cover different market and network requirements, with an appropriate balance of performance to cost and effective and appropriate use of the radio spectrum, the present document, together with EN 302 217-4-2 [8], offers a number of system types and antennas alternatives, for selection by administrations, operators and manufacturers dependent on the desired use of the radio spectrum and network/market requirements; those options include: • channel separation alternatives (as provided by the relevant CEPT or Recommendation ITU-R); • spectral efficiency class alternatives (different modulation formats provided in radio equipment standards) as defined in clause 1.2; actual equipment may operate within one spectral efficiency class only (Single-mode) or within multiple classes, either with static pre-selection of the class (Preset-mode) or with dynamic variation of capacity according the propagation conditions (Mixed-mode) (see note); • antenna directivity class alternatives (for different network requirements). NOTE: Single- mode, Preset-mode and Mixed-mode systems are defined in clause 3.1 of EN 302 217-1 [6]; additional information on Mixed-mode systems may be found in annex I of the present document and in TR 103 103 [i.35]. SIST EN 302 217-2-2 V2.2.1:2014

ETSI ETSI EN 302 217-2-2 V2.2.1 (2014-04)10 1.4 Channel arrangements and utilization Systems in the scope of the present document are intended to operate only in full frequency division duplex (FDD). Time division duplex (TDD) applications are not in the scope of the present document. Unidirectional systems are assumed to be an underequipped FDD system. From the point of view of the transmission capacity, these systems are defined, in the relevant annexes, on the basis of their minimum Channel Separation (CS) on the same route, for a given spectral efficiency class, taken into account by the system design. The possible channel arrangements may be: • Adjacent Channel Alternate-Polarized (ACAP); • Adjacent Channel Co-Polarized (ACCP); • Co-Channel Dual-Polarization (CCDP). These possible applications and their channel arrangements are shown in figure 2a. ACCPV or HCCDPVHACAPVH Figure 2a: Examples of channel arrangements on the same route 1.5 Payload flexibility For quick identification of the system, the capacities in tables X.2 (where X = A, B, C, D, E, Ea represents the relevant annex) are the minimum transmitted RIC required for conformance to the present document; they are based on the "minimum RIC density" defined in clause 1.2. Only some cases of systems in annex A, due to the smaller channel separation provided, are (exceptionally) labelled with typical gross bit rate rather than minimum RIC capacity rates. However, equipment may offer a variety of base band interfaces, e.g. typical hierarchical rates PDH or SDH, ISDN, Ethernet as well as mixture of these or other standardized interfaces. Mapping/multiplexing of the various base-band interfaces into common frame(s) suitable for radio transmission may be done using standardized higher hierarchical frames or other proprietary methods. NOTE: Information on applicable base-band interfaces can be found in EN 302 217-1 [6]. Tables F.1a through F.1g in annex F summarize the "minimum RIC" considered in the present document and, when only PDH or SDH interfaces are provided, give the equivalent capacity in term of number of 2,048 Mbit/s streams provided as multiple or single multiplexed PDH or SDH interfaces. These minimum capacities will be associated to the relevant channel separation and spectral efficiency classes defined. Equipment may operate with one single RIC payload rate or with multiple RIC payload rates (multirate systems), either statically preset (possibly coupled also with preset-mode operation) or, when coupled with mixed-mode operation, dynamically changing according to the modulation format. The requirements of the present document apply separately to each transmitter/receiver or single transmitters or receivers used for combining complex or simple (e.g. space diversity receivers or single transmitters and receivers used
...