SIST EN 302 217-1 V3.2.2:2020

Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)

EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements

2 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)

Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
ETSI
4 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
7.2.1.2 Combined TX power and EIRP limits . 34
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
ETSI
5 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
A.2.2.2 Receiver selectivity . 49
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73

ETSI
6 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals,
Transmission and Multiplexing (ATTM), and is now submitted for the Vote phase of the ETSI standards EN Approval
Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity will cease on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

ETSI
7 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
8 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment. These requirements are introduced in
two different clauses sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper
system operation and deployment when specific deployment conditions or compatibility requirements are
present. Compliance to all or some of these requirements is left to manufacturer decision.
Technical background for most of the parameters and requirements referred to in this multi-part deliverable may be
found in ETSI TR 101 036-1 [i.16].
Health and safety requirements and EMC conditions and requirements are not considered in the ETSI EN 302 217
series.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 122150 : "Sectional Specification: Radio frequency coaxial connectors - Series
EIA flange".
[2] CEPT/ERC/DEC(00)07: "The shared use of the band 17.7 - 19.7 GHz by the fixed service and
earth stations of the fixed-satellite service (space-to-Earth)". ERC Decision, approved
19 October 2000, amended 04 March 2016.
[3] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[4] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
ETSI
9 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[7] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[8] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[9] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weather protected locations".
[10] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weather protected locations".
[11] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weather protected locations".
[12] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weather protected locations".
[13] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: Operated by -48 V Direct
Current (DC)".
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input to
telecommunications equipment; Part 3: Operated by rectified current source, alternating current
source or direct current source up to 400 V".
[15] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[16] ETSI EN 302 099: "Environmental Engineering (EE); Powering of equipment in access network".
[17] ETSI EN 301 126-3-1: "Fixed Radio Systems; Conformance testing; Part 3-1: Point-to-Point
antennas; Definitions, general requirements and test procedures".
[18] ETSI EN 302 217-2 (V3.2.0): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz
to 86 GHz; Harmonised Standard for access to radio spectrum".
[19] ETSI EN 302 217-4 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 4: Antennas".
[20] CENELEC EN 60835-2-4: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 4:
Transmitter/receiver including modulator/demodulator".
[21] CENELEC EN 60835-2-8: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 8:
Adaptive equalizer".
[22] IEEE 802.3-2012™: "IEEE Standard for Ethernet".
[23] Recommendation ITU-R F.746: "Radio-frequency arrangements for fixed service systems".
ETSI
10 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
[24] Recommendation ITU-R F.1668: "Error performance objectives for real digital fixed wireless links
used in 27 500 km hypothetical reference paths and connections".
[25] Recommendation ITU-R F.1703: "Availability objectives for real digital fixed wireless links used
in 27 500 km hypothetical reference paths and connections".
[26] Recommendation ITU-R P.530: "Propagation data and prediction methods required for the design
of terrestrial line-of-sight systems".
[27] Recommendation ITU-T G.703: "Physical/electrical characteristics of hierarchical digital
interfaces".
[28] Recommendation ITU-T G.704: "Synchronous frame structures used at 1544, 6312, 2048, 8448
and 44 736 kbit/s hierarchical levels".
[29] Recommendation ITU-T G.707: "Network node interface for the synchronous digital hierarchy
(SDH)".
[30] Recommendation ITU-T G.708: "Sub STM-0 network node interface for the synchronous digital
hierarchy (SDH)".
[31] Recommendation ITU-T G.826: "End-to-end error performance parameters and objectives for
international, constant bit-rate digital paths and connections".
[32] Recommendation ITU-T G.828: "Error performance parameters and objectives for international,
constant bit-rate synchronous digital paths".
[33] Recommendation ITU-T G.829: "Error performance events for SDH multiplex and regenerator
sections".
[34] Recommendation ITU-T G.957: "Optical interfaces for equipment and systems relating to the
synchronous digital hierarchy".
[35] Recommendation ITU-T I.356: "B-ISDN ATM layer cell transfer performance".
[36] Recommendation ITU-T I.357: "B-ISDN semi-permanent connection availability".
[37] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary rate and above".
[38] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces".
[39] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM
connections".
[40] Recommendation ITU-T V.11: "Electrical characteristics for balanced double-current interchange
circuits operating at data signalling rates up to 10 Mbit/s".
[41] Recommendation ITU-T V.24: "List of definitions for interchange circuits between data terminal
equipment (DTE) and data circuit-terminating equipment (DCE)".
[42] Recommendation ITU-T V.28: "Electrical characteristics for unbalanced double-current
interchange circuits".
[43] Recommendation ITU-T Y.1540: "Internet protocol data communication service - IP packet
transfer and availability performance parameters".
ETSI
11 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 101 035: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH)
aspects regarding Digital Radio Relay Systems (DRRS)".
[i.3] ETSI TR 102 243-1: "Fixed Radio Systems; Representative values for transmitter power and
antenna gain to support inter- and intra-compatibility and sharing analysis; Part 1: Digital point-to-
point systems".
[i.4] CEPT/ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial
fixed systems operating in the band 17.7 GHz to 19.7 GHz".
[i.5] Void.
[i.6] CEPT/ECC/REC(02)06: "Preferred channel arrangements for digital Fixed Service Systems
operating in the frequency range 7125-8500 MHz".
[i.7] CEPT/ECC/Report 80: "Enhancing harmonisation and introducing flexibility in the spectrum
regulatory framework".
[i.8] CEPT/ECC/Report 198: "Adaptive modulation and ATPC operations in fixed point-to-point
systems - Guideline on coordination procedures".
[i.9] CEPT/ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and
digital radio-relay systems operating in the band 5925 MHz to 6425 MHz".
[i.10] CEPT/ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low
capacity digital fixed service systems operating in the band 6425 to 7125 MHz".
[i.11] ETSI EN 301 489-1: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements; Harmonised Standard for ElectroMagnetic
Compatibility".
[i.12] ETSI EN 301 489-4: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 4: Specific conditions for fixed radio links and ancillary equipment; Harmonised
Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU".
[i.13] ETSI EN 302 217-1 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 1: Overview and system-independent common
characteristics".
NOTE: The ETSI EN 302 217-1 (V2.1.1) is not applicable in Directive 2014/53/EU [i.1] regime.
[i.14] Void.
[i.15] ETSI EN 300 119 (all parts): "Environmental Engineering (EE); European telecommunication
standard for equipment practice".
[i.16] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital
Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment
parameters".
ETSI
12 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
[i.17] ETSI TR 101 506 (V2.1.1): "Fixed Radio Systems; Generic definitions, terminology and
applicability of essential requirements covering article 3.2 of Directive 2014/53/EU to Fixed Radio
Systems".
[i.18] ETSI TR 101 854: "Fixed Radio Systems; Point-to-point equipment; Derivation of receiver
interference parameters useful for planning fixed service point-to-point systems operating different
equipment classes and/or capacities".
[i.19] ETSI TR 103 103: "Fixed Radio Systems; Point-to-point systems; ATPC, RTPC, Adaptive
Modulation (mixed-mode) and Bandwidth Adaptive functionalities; Technical background and
impact on deployment, link design and coordination".
[i.20] CENELEC EN 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for
ordinary rectangular waveguides".
[i.21] CENELEC EN 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for
ordinary rectangular waveguides".
[i.22] IEC 60169-1 : "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[i.23] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
connectors".
[i.24] Recommendation ITU-R F.383-9: "Radio-frequency channel arrangements for high capacity fixed
wireless systems operating in the lower 6 GHz (5 925 to 6 425 MHz) band".
[i.25] Recommendation ITU-R F.384-11: "Radio -frequency channel arrangements for medium- and
high-capacity digital fixed wireless systems operating in the 6 425-7 125 MHz band".
[i.26] Recommendation ITU-R F.385-10: "Radio-frequency channel arrangements for fixed wireless
systems operating in the 7 110-7 900 MHz band".
[i.27] Recommendation ITU-R F.595-10: "Radio-frequency channel arrangements for fixed wireless
systems operating in the 17.7-19.7 GHz frequency band".
[i.28] Recommendation ITU-R F.750: "Architectures and functional aspects of radio-relay systems for
synchronous digital hierarchy (SDH)-based network".
[i.29] Void.
[i.30] Recommendation ITU-R F.752: "Diversity techniques for point-to-point fixed wireless systems".
[i.31] Recommendation ITU-R F.1093: "Effects of multipath propagation on the design and operation of
line-of-sight digital fixed
...

EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements

2 ETSI EN 302 217-1 V3.2.2 (2020-02)

Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 217-1 V3.2.2 (2020-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
4 ETSI EN 302 217-1 V3.2.2 (2020-02)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 40
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
5 ETSI EN 302 217-1 V3.2.2 (2020-02)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73

ETSI
6 ETSI EN 302 217-1 V3.2.2 (2020-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity ceased on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.

National transposition dates
Date of adoption of this EN: 4 February 2020
Date of latest announcement of this EN (doa): 31 May 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2020
Date of withdrawal of any conflicting National Standard (dow): 30 November 2020

ETSI
7 ETSI EN 302 217-1 V3.2.2 (2020-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
8 ETSI EN 302 217-1 V3.2.2 (2020-02)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment. These requirements are introduced in
two different clauses sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper
system operation and deployment when specific deployment conditions or compatibility requirements are
present. Compliance to all or some of these requirements is left to manufacturer decision.
Technical background for most of the parameters and requirements referred to in this multi-part deliverable may be
found in ETSI TR 101 036-1 [i.16].
Health and safety requirements and EMC conditions and requirements are not considered in the ETSI EN 302 217
series.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 122150 : "Sectional Specification: Radio frequency coaxial connectors - Series
EIA flange".
[2] CEPT/ERC/DEC(00)07: "The shared use of the band 17.7 - 19.7 GHz by the fixed service and
earth stations of the fixed-satellite service (space-to-Earth)". ERC Decision, approved
19 October 2000, amended 04 March 2016.
[3] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[4] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
ETSI
9 ETSI EN 302 217-1 V3.2.2 (2020-02)
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[7] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[8] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[9] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weather protected locations".
[10] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weather protected locations".
[11] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weather protected locations".
[12] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weather protected locations".
[13] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: Operated by -48 V Direct
Current (DC)".
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input to
telecommunications equipment; Part 3: Operated by rectified current source, alternating current
source or direct current source up to 400 V".
[15] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[16] ETSI EN 302 099: "Environmental Engineering (EE); Powering of equipment in access network".
[17] ETSI EN 301 126-3-1: "Fixed Radio Systems; Conformance testing; Part 3-1: Point-to-Point
antennas; Definitions, general requirements and test procedures".
[18] ETSI EN 302 217-2 (V3.2.2): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz
to 86 GHz; Harmonised Standard for access to radio spectrum".
[19] ETSI EN 302 217-4 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 4: Antennas".
[20] CENELEC EN 60835-2-4: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 4:
Transmitter/receiver including modulator/demodulator".
[21] CENELEC EN 60835-2-8: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 8:
Adaptive equalizer".
[22] IEEE 802.3-2012™: "IEEE Standard for Ethernet".
[23] Recommendation ITU-R F.746: "Radio-frequency arrangements for fixed service systems".
ETSI
10 ETSI EN 302 217-1 V3.2.2 (2020-02)
[24] Recommendation ITU-R F.1668: "Error performance objectives for real digital fixed wireless links
used in 27 500 km hypothetical reference paths and connections".
[25] Recommendation ITU-R F.1703: "Availability objectives for real digital fixed wireless links used
in 27 500 km hypothetical reference paths and connections".
[26] Recommendation ITU-R P.530: "Propagation data and prediction methods required for the design
of terrestrial line-of-sight systems".
[27] Recommendation ITU-T G.703: "Physical/electrical characteristics of hierarchical digital
interfaces".
[28] Recommendation ITU-T G.704: "Synchronous frame structures used at 1544, 6312, 2048, 8448
and 44 736 kbit/s hierarchical levels".
[29] Recommendation ITU-T G.707: "Network node interface for the synchronous digital hierarchy
(SDH)".
[30] Recommendation ITU-T G.708: "Sub STM-0 network node interface for the synchronous digital
hierarchy (SDH)".
[31] Recommendation ITU-T G.826: "End-to-end error performance parameters and objectives for
international, constant bit-rate digital paths and connections".
[32] Recommendation ITU-T G.828: "Error performance parameters and objectives for international,
constant bit-rate synchronous digital paths".
[33] Recommendation ITU-T G.829: "Error performance events for SDH multiplex and regenerator
sections".
[34] Recommendation ITU-T G.957: "Optical interfaces for equipment and systems relating to the
synchronous digital hierarchy".
[35] Recommendation ITU-T I.356: "B-ISDN ATM layer cell transfer performance".
[36] Recommendation ITU-T I.357: "B-ISDN semi-permanent connection availability".
[37] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary rate and above".
[38] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces".
[39] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM
connections".
[40] Recommendation ITU-T V.11: "Electrical characteristics for balanced double-current interchange
circuits operating at data signalling rates up to 10 Mbit/s".
[41] Recommendation ITU-T V.24: "List of definitions for interchange circuits between data terminal
equipment (DTE) and data circuit-terminating equipment (DCE)".
[42] Recommendation ITU-T V.28: "Electrical characteristics for unbalanced double-current
interchange circuits".
[43] Recommendation ITU-T Y.1540: "Internet protocol data communication service - IP packet
transfer and availability performance parameters".
ETSI
11 ETSI EN 302 217-1 V3.2.2 (2020-02)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 101 035: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH)
aspects regarding Digital Radio Relay Systems (DRRS)".
[i.3] ETSI TR 102 243-1: "Fixed Radio Systems; Representative values for transmitter power and
antenna gain to support inter- and intra-compatibility and sharing analysis; Part 1: Digital point-to-
point systems".
[i.4] CEPT/ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial
fixed systems operating in the band 17.7 GHz to 19.7 GHz".
[i.5] Void.
[i.6] CEPT/ECC/REC(02)06: "Preferred channel arrangements for digital Fixed Service Systems
operating in the frequency range 7125-8500 MHz".
[i.7] CEPT/ECC/Report 80: "Enhancing harmonisation and introducing flexibility in the spectrum
regulatory framework".
[i.8] CEPT/ECC/Report 198: "Adaptive modulation and ATPC operations in fixed point-to-point
systems - Guideline on coordination procedures".
[i.9] CEPT/ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and
digital radio-relay systems operating in the band 5925 MHz to 6425 MHz".
[i.10] CEPT/ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low
capacity digital fixed service systems operating in the band 6425 to 7125 MHz".
[i.11] ETSI EN 301 489-1: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements; Harmonised Standard for ElectroMagnetic
Compatibility".
[i.12] ETSI EN 301 489-4: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 4: Specific conditions for fixed radio links and ancillary equipment; Harmonised
Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU".
[i.13] ETSI EN 302 217-1 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 1: Overview and system-independent common
characteristics".
NOTE: The ETSI EN 302 217-1 (V2.1.1) is not applicable in Directive 2014/53/EU [i.1] regime.
[i.14] Void.
[i.15] ETSI EN 300 119 (all parts): "Environmental Engineering (EE); European telecommunication
standard for equipment practice".
[i.16] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital
Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment
parameters".
ETSI
12 ETSI EN 302 217-1 V3.2.2 (2020-02)
[i.17] ETSI TR 101 506 (V2.1.1): "Fixed Radio Systems; Generic definitions, terminology and
applicability of essential requirements covering article 3.2 of Directive 2014/53/EU to Fixed Radio
Systems".
[i.18] ETSI TR 101 854: "Fixed Radio Systems; Point-to-point equipment; Derivation of receiver
interference parameters useful for planning fixed service point-to-point systems operating different
equipment classes and/or capacities".
[i.19] ETSI TR 103 103: "Fixed Radio Systems; Point-to-point systems; ATPC, RTPC, Adaptive
Modulation (mixed-mode) and Bandwidth Adaptive functionalities; Technical background and
impact on deployment, link design and coordination".
[i.20] CENELEC EN 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for
ordinary rectangular waveguides".
[i.21] CENELEC EN 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for
ordinary rectangular waveguides".
[i.22] IEC 60169-1 : "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[i.23] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
connectors".
[i.24] Recommendation ITU-R F.383-9: "Radio-frequency channel arrangements for high capacity fixed
wireless systems operating in the lower 6 GHz (5 925 to 6 425 MHz) band".
[i.25] Recommendation ITU-R F.384-11: "Radio -frequency channel arrangements for medium- and
high-capacity digital fixed wireless systems operating in the 6 425-7 125 MHz band".
[i.26] Recommendation ITU-R F.385-10: "Radio-frequency channel arrangements for fixed wireless
systems operating in the 7 110-7 900 MHz band".
[i.27] Recommendation ITU-R F.595-10: "Radio-frequency channel arrangements for fixed wireless
systems operating in the 17.7-19.7 GHz frequency band".
[i.28] Recommendation ITU-R F.750: "Architectures and functional aspects of radio-relay systems for
synchronous digital hierarchy (SDH)-based network".
[i.29] Void.
[i.30] Recommendation ITU-R F.752: "Diversity techniques for point-to-point fixed wireless systems".
[i.31] Recommendation ITU-R F.1093: "Effects of multipath propagation on the design and operation of
line-of-sight digital fixed wireless systems".
[i.32] Recommendation ITU-R F.1101: "Characteristics of digital fixed wireless systems below about
17 GHz".
[i.33] Recommendation ITU-R F.1102: "Characteristics of fixed wireless systems operating in frequency
...

SLOVENSKI STANDARD
01-april-2020
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in
antene - 1. del: Pregled, splošne karakteristike in sistemsko neodvisne zahteve
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 1: Overview, common characteristics and system-independent
requirements
Ta slovenski standard je istoveten z: ETSI EN 302 217-1 V3.2.2 (2020-02)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements

2 ETSI EN 302 217-1 V3.2.2 (2020-02)

Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 217-1 V3.2.2 (2020-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
4 ETSI EN 302 217-1 V3.2.2 (2020-02)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 40
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
5 ETSI EN 302 217-1 V3.2.2 (2020-02)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73

ETSI
6 ETSI EN 302 217-1 V3.2.2 (2020-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity ceased on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.

National transposition dates
Date of adoption of this EN: 4 February 2020
Date of latest announcement of this EN (doa): 31 May 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2020
Date of withdrawal of any conflicting National Standard (dow): 30 November 2020

ETSI
7 ETSI EN 302 217-1 V3.2.2 (2020-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
8 ETSI EN 302 217-1 V3.2.2 (2020-02)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment. These requirements are introduced in
two different clauses sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper
system operation and deployment when specific deployment conditions or compatibility requirements are
present. Compliance to all or some of these requirements is left to manufacturer decision.
Technical background for most of the parameters and requirements referred to in this multi-part deliverable may be
found in ETSI TR 101 036-1 [i.16].
Health and safety requirements and EMC conditions and requirements are not considered in the ETSI EN 302 217
series.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 122150 : "Sectional Specification: Radio frequency coaxial connectors - Series
EIA flange".
[2] CEPT/ERC/DEC(00)07: "The shared use of the band 17.7 - 19.7 GHz by the fixed service and
earth stations of the fixed-satellite service (space-to-Earth)". ERC Decision, approved
19 October 2000, amended 04 March 2016.
[3] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[4] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
ETSI
9 ETSI EN 302 217-1 V3.2.2 (2020-02)
[5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[6] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-1: Specification of environmental
tests; Storage".
[7] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-2: Classification of environmental
conditions; Transportation".
[8] ETSI EN 300 019-2-2: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-2: Specification of environmental
tests; Transportation".
[9] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-3: Classification of environmental
conditions; Stationary use at weather protected locations".
[10] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-3: Specification of environmental
tests; Stationary use at weather protected locations".
[11] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-4: Classification of environmental
conditions; Stationary use at non-weather protected locations".
[12] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-4: Specification of environmental
tests; Stationary use at non-weather protected locations".
[13] ETSI EN 300 132-2: "Environmental Engineering (EE); Power supply interface at the input of
Information and Communication Technology (ICT) equipment; Part 2: Operated by -48 V Direct
Current (DC)".
[14] ETSI EN 300 132-3: "Environmental Engineering (EE); Power supply interface at the input to
telecommunications equipment; Part 3: Operated by rectified current source, alternating current
source or direct current source up to 400 V".
[15] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point
equipment - Definitions, general requirements and test procedures".
[16] ETSI EN 302 099: "Environmental Engineering (EE); Powering of equipment in access network".
[17] ETSI EN 301 126-3-1: "Fixed Radio Systems; Conformance testing; Part 3-1: Point-to-Point
antennas; Definitions, general requirements and test procedures".
[18] ETSI EN 302 217-2 (V3.2.2): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz
to 86 GHz; Harmonised Standard for access to radio spectrum".
[19] ETSI EN 302 217-4 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 4: Antennas".
[20] CENELEC EN 60835-2-4: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 4:
Transmitter/receiver including modulator/demodulator".
[21] CENELEC EN 60835-2-8: "Methods of measurement for equipment used in digital microwave
radio transmission systems - Part 2: Measurements on terrestrial radio-relay systems - Section 8:
Adaptive equalizer".
[22] IEEE 802.3-2012™: "IEEE Standard for Ethernet".
[23] Recommendation ITU-R F.746: "Radio-frequency arrangements for fixed service systems".
ETSI
10 ETSI EN 302 217-1 V3.2.2 (2020-02)
[24] Recommendation ITU-R F.1668: "Error performance objectives for real digital fixed wireless links
used in 27 500 km hypothetical reference paths and connections".
[25] Recommendation ITU-R F.1703: "Availability objectives for real digital fixed wireless links used
in 27 500 km hypothetical reference paths and connections".
[26] Recommendation ITU-R P.530: "Propagation data and prediction methods required for the design
of terrestrial line-of-sight systems".
[27] Recommendation ITU-T G.703: "Physical/electrical characteristics of hierarchical digital
interfaces".
[28] Recommendation ITU-T G.704: "Synchronous frame structures used at 1544, 6312, 2048, 8448
and 44 736 kbit/s hierarchical levels".
[29] Recommendation ITU-T G.707: "Network node interface for the synchronous digital hierarchy
(SDH)".
[30] Recommendation ITU-T G.708: "Sub STM-0 network node interface for the synchronous digital
hierarchy (SDH)".
[31] Recommendation ITU-T G.826: "End-to-end error performance parameters and objectives for
international, constant bit-rate digital paths and connections".
[32] Recommendation ITU-T G.828: "Error performance parameters and objectives for international,
constant bit-rate synchronous digital paths".
[33] Recommendation ITU-T G.829: "Error performance events for SDH multiplex and regenerator
sections".
[34] Recommendation ITU-T G.957: "Optical interfaces for equipment and systems relating to the
synchronous digital hierarchy".
[35] Recommendation ITU-T I.356: "B-ISDN ATM layer cell transfer performance".
[36] Recommendation ITU-T I.357: "B-ISDN semi-permanent connection availability".
[37] Recommendation ITU-T O.151: "Error performance measuring equipment operating at the
primary rate and above".
[38] Recommendation ITU-T O.181: "Equipment to assess error performance on STM-N interfaces".
[39] Recommendation ITU-T O.191: "Equipment to measure the cell transfer performance of ATM
connections".
[40] Recommendation ITU-T V.11: "Electrical characteristics for balanced double-current interchange
circuits operating at data signalling rates up to 10 Mbit/s".
[41] Recommendation ITU-T V.24: "List of definitions for interchange circuits between data terminal
equipment (DTE) and data circuit-terminating equipment (DCE)".
[42] Recommendation ITU-T V.28: "Electrical characteristics for unbalanced double-current
interchange circuits".
[43] Recommendation ITU-T Y.1540: "Internet protocol data communication service - IP packet
transfer and availability performance parameters".
ETSI
11 ETSI EN 302 217-1 V3.2.2 (2020-02)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 101 035: "Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH)
aspects regarding Digital Radio Relay Systems (DRRS)".
[i.3] ETSI TR 102 243-1: "Fixed Radio Systems; Representative values for transmitter power and
antenna gain to support inter- and intra-compatibility and sharing analysis; Part 1: Digital point-to-
point systems".
[i.4] CEPT/ERC/REC 12-03: "Harmonised radio frequency channel arrangements for digital terrestrial
fixed systems operating in the band 17.7 GHz to 19.7 GHz".
[i.5] Void.
[i.6] CEPT/ECC/REC(02)06: "Preferred channel arrangements for digital Fixed Service Systems
operating in the frequency range 7125-8500 MHz".
[i.7] CEPT/ECC/Report 80: "Enhancing harmonisation and introducing flexibility in the spectrum
regulatory framework".
[i.8] CEPT/ECC/Report 198: "Adaptive modulation and ATPC operations in fixed point-to-point
systems - Guideline on coordination procedures".
[i.9] CEPT/ERC/REC 14-01: "Radio-frequency channel arrangements for high capacity analogue and
digital radio-relay systems operating in the band 5925 MHz to 6425 MHz".
[i.10] CEPT/ERC/REC 14-02: "Radio-frequency channel arrangements for high, medium and low
capacity digital fixed service systems operating in the band 6425 to 7125 MHz".
[i.11] ETSI EN 301 489-1: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements; Harmonised Standard for ElectroMagnetic
Compatibility".
[i.12] ETSI EN 301 489-4: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 4: Specific conditions for fixed radio links and ancillary equipment; Harmonised
Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU".
[i.13] ETSI EN 302 217-1 (V2.1.1): "Fixed Radio Systems; Characteristics and requirements for point-
to-point equipment and antennas; Part 1: Overview and system-independent common
characteristics".
NOTE: The ETSI EN 302 217-1 (V2.1.1) is not applicable in Directive 2014/53/EU [i.1] regime.
[i.14] Void.
[i.15] ETSI EN 300 119 (all parts): "Environmental Engineering (EE); European telecommunication
standard for equipment practice".
[i.16] ETSI TR 101 036-1: "Fixed Radio Systems; Generic wordings for standards on DFRS (Digital
Fixed Radio Systems) characteristics; Part 1: General aspects and point-to-point equipment
parameters".
ETSI
12 ETSI EN 302 217-1 V3.2.2 (2020-02)
[i.17] ETSI TR 101 506 (V2.1.1): "Fixed Radio Systems; Generic definitions, terminology and
applicability of essential requirements covering article 3.2 of Directive 2014/53/EU to Fixed Radio
Systems".
[i.18] ETSI TR 101 854: "Fixed Radio Systems; Point-to-point equipment; Derivation of receiver
interference parameters useful for planning fixed service point-to-point systems operating different
equipment classes and/or capacities".
[i.19] ETSI TR 103 103: "Fixed Radio Systems; Point-to-point systems; ATPC, RTPC, Adaptive
Modulation (mixed-mode) and Bandwidth Adaptive functionalities; Technical background and
impact on deployment, link design and coordination".
[i.20] CENELEC EN 60153-2: "Hollow metallic waveguides. Part 2: Relevant specifications for
ordinary rectangular waveguides".
[i.21] CENELEC EN 60154-2: "Flanges for waveguides. Part 2: Relevant specifications for flanges for
ordinary rectangular waveguides".
[i.22] IEC 60169-1 : "Radio-frequency connectors. Part 1: General requirements and measuring
methods".
[i.23] IEC 60339 (all parts): "General purpose rigid coaxial transmission lines and their associated flange
...