SIST EN 61169-2:2007

SLOVENSKI STANDARD
01-november-2007
5DGLRIUHNYHQþQLNRQHNWRUML±GHO3RGURþQDVSHFLILNDFLMD±5DGLRIUHNYHQþQL
NRDNVLDOQLNRQHNWRUMLWLSD,(&
Radio-frequency connectors -- Part 2: Sectional specification - Radio frequency coaxial
connectors of type 9,52 (IEC 61169-2:2007)
Hochfrequenz-Steckverbinder – Teil 2: Rahmenspezifikation – Koaxiale
Hochfrequenzsteckverbinder Typ 9,52 (IEC 61169-2:2007)
Connecteurs pour fréquences radioélectriques -- Partie 2: Spécification intermédiaire -
Connecteurs pour fréquences radioélectriques de série 9,52 (IEC 61169-2:2007)
Ta slovenski standard je istoveten z: EN 61169-2:2007
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61169-2
NORME EUROPÉENNE
March 2007
EUROPÄISCHE NORM
ICS 31.220.10 Supersedes EN 61169-2:2001

English version
Radio-frequency connectors -
Part 2: Sectional specification -
Radio frequency coaxial connectors of type 9,52
(IEC 61169-2:2007)
Connecteurs pour fréquences Hochfrequenz-Steckverbinder -
radioélectriques - Teil 2: Rahmenspezifikation -
Partie 2: Spécification intermédiaire - Koaxiale Hochfrequenzsteckverbinder
Connecteurs pour fréquences Typ 9,52
radioélectriques de série 9,52 (IEC 61169-2:2007)
(CEI 61169-2:2007)
This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61169-2:2007 E
Foreword
The text of document 46F/56/FDIS, future edition 2 of IEC 61169-2, prepared by SC 46F, R.F. and
microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 61169-2 on 2007-03-01.
This European Standard supersedes EN 61169-2:2001.
The main change introduced in EN 61169-2:2007 is that the maximum frequency is now 3 GHz.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61169-2:2007 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61169-2:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61169-1 1992 Radio-frequency connectors - EN 61169-1 1994
Part 1: Generic specification - General
requirements and measuring methods

INTERNATIONAL IEC
STANDARD 61169-2
QC 220200
Second edition
2007-02
Radio-frequency connectors –
Part 2:
Sectional specification –
Radio frequency coaxial connectors of type 9,52

© IEC 2007 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale R
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 61169-2 © IEC:2007(E)
CONTENTS
FOREWORD.3

1 Scope.5
2 Normative references .5
3 Interface dimensions .5
3.1 Interface.5
3.2 Mechanical gauges.9
4 Quality assessment procedures.10
4.1 General .10
4.2 Ratings and characteristics .10
4.3 Test schedule and inspection requirements .12
4.4 Procedures.14
5 Instructions for preparation of detail specifications .14
5.1 General .14
5.2 Identification of the detail specification .14
5.3 Identification of the component.15
5.4 Performance.15
5.5 Marking, ordering information and related matters .15
5.6 Selection of tests, test conditions and severities.15
5.7 Blank detail specification pro-forma for type 9,52 connector .16

Figure 1a – Sliding male connector .6
Figure 1b – Sliding female connector .6
Figure 1 – Sliding connector .6
Figure 2a – Screw coupling male connector .7
Figure 2b – Screw coupling female connector .7
Figure 2 – Screw coupling connector .7
Figure 3a – Standard test male connector.8
Figure 3b – Standard test female connector.8
Figure 3 – Standard test connectors .8
Figure 4 – Gauge pins for outer contact of socket connector.9
Figure 5 – Gauge pins for centre contact of socket connector .10

Table 1 – Ratings and characteristics .11
Table 2 – Acceptance tests.12
Table 3 – Periodic tests .13

61169-2 © IEC:2007(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
RADIO-FREQUENCY CONNECTORS –
Part 2: Sectional specification –
Radio frequency coaxial connectors of type 9,52

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-2 Ed: 2.0 has been prepared by subcommittee 46F: R.F.
and microwave passive components, of IEC technical committee 46: Cables, wires,
waveguides, R.F. connectors, R.F. and microwave passive components and accessories.
This second edition cancels and replaces the first edition published in 2001. It constitutes a
technical revision.
The main change introduced in this edition is that the maximum frequency is now 3 GHZ.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/56/FDIS 46F/66/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

– 4 – 61169-2 © IEC:2007(E)
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61169 series, published under the general title Radio-frequency
connectors, can be found on the IEC website.
The QC number that appears on the front cover of this publication is the specification number
in the IEC Quality Assessment System for Electronic Components (IECQ).
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual edition of this document may be issued at a later date.

61169-2 © IEC:2007(E) – 5 –
RADIO-FREQUENCY CONNECTORS –
Part 2: Sectional specification –
Radio frequency coaxial connectors type 9,52

1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for RF coaxial connectors of type 9,52.
It describes the interface dimensions for general purpose grade 2 connectors, dimensional
details for standard test connectors, grade 0, together with gauging information and the
mandatory tests selected from IEC 61169-1, applicable to all DS relating to type 9,52
connectors.
This specification indicates the recommended performance characteristics to be considered
when writing a DS and covers test schedules and inspection requirements.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 61169-1:1992, Radio-frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
3 Interface dimensions
3.1 Interface
3.1.1 General
All dimensions are in millimetres.
All undimensioned pictorial configurations are for reference purposes only.
3.1.2 Dimensions
Figures 1, 2 and 3 provide dimensions for sliding connectors, screw coupling connectors and
standard test connectors respectively.

– 6 – 61169-2 © IEC:2007(E)
9,1 min.
+0,43
7,11
0,8 ± 0,4
2 max.
Cone or radius
IEC  105/07
Figure 1a – Sliding male connector

7,54 min.
+1,5
0,5
IEC  106/07
Figure 1b – Sliding female connector

Figure 1 – Sliding connector
+0,3
∅1
–0,1
+0,03
∅2,35
–0,08
∅8,5 min.
∅9,525 ± 0,05
61169-2 © IEC:2007(E) – 7 –
+0,43
7,11
4 ± 0,5
Optional sealing
4 min.
gasket
IEC  107/07
Figure 2a – Screw coupling male connector
5 min.
IEC  108/07
Figure 2b – Screw coupling female connector

Figure 2 – Screw coupling connector

M14 × 1
M14 × 1
– 8 – 61169-2 © IEC:2007(E)
9,1 min.
+0,43
7,11
0,8 ± 0,4
2 max.
4 min.
IEC  109/07
Figure 3a – Standard test male connector

7,54 min.
7,2 min.
5 min.
+0,2
0,5
4 slots
width 0,3 mm
lenght 4,5 mm
IEC  110/07
Figure 3b – Standard test female connector

Figure 3 – Standard test connectors

M14 × 1
∅3,2 ± 0,02
+0,3
∅1
–0,1
∅2,35 ± 0,01
∅8,5 ± 0,02
∅9,525 ± 0,05
M14 × 1
61169-2 © IEC:2007(E) – 9 –
3.2 Mechanical gauges
3.2.1 General
All dimensions are in millimetres.
All undimensioned pictorial configurations are for reference purposes only.
3.2.2 Socket connectors – Gauges for the resilient outer contact
Figure 4 illustrates gauge pins for outer contacts of socket connectors.

∅a
7 ± 0,5
IEC  111/07
Surface finish: Ra <=0,5
Weight: 5 N
Gauge A Gauge B
Reference mm mm
Min. Max. Min. Max.
9,575 9,585 9,465 9,475
∅ a
b 5,0 5,2 7,0 7,2
Test sequence
a) Steel test pin (A) (Figure 4) shall be inserted at least three times into the outer contact.
b) A second steel test pin (B) (Figure 4) shall be inserted into the outer contact.
This gauge, when in a vertical downward attitude, shall be retained by the contact.
Figure 4 – Gauge pins for outer contact of socket connector

b
– 10 – 61169-2 © IEC:2007(E)
3.2.3 Socket connectors – Gauges for the resilient centre contact
Figure 4 illustrates gauge pins for outer contacts of socket connectors.

∅a
R0,5
–0,1
IEC  112/07
Surface finish: Ra <=0,5
Gauge C Gauge D
Reference mm mm
Min. Max. Min. Max.
∅ a 2,38 2,39 2,29 2,30
Test sequence
a) Steel test pin (C) (Figure 5) shall be inserted at least three times into the centre contact.
b) A second steel test pin (D) (Figure 5) shall be inserted into the centre contact.
This gauge, when in a vertical downward attitude, shall be retained by the contact.
This gauge will have a mass (weight) of 0,25 N.
Figure 5 – Gauge pins for centre contact of socket connector
4 Quality assessment procedures
4.1 General
The following subclauses provide recommended ratings, performance and test conditions to
be considered when writing a detail
...