SIST EN 851:2014
(Main)Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
EN 851 specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications. This standard is applicable to: - Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm. - Hot or cold-rolled circle stock with a thickness from 2 mm up to and including 12 mm and with a width up to 1 600 mm. This European Standard is not applicable to slugs for impact extrusions which are dealt with in other European Standards.
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - Spezifikationen
Diese Europäische Norm legt die besonderen Anforderungen für Ronden und Rondenvormaterial aus Aluminium-Knetlegierung und Aluminiumlegierungen fest, die zur Herstellung von Küchengeschirr eingesetzt werden.
Diese Norm gilt für:
- Ronden, die aus kalt- bzw. warmgewalztem Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einem Durchmesser von 100 mm bis 1 600 mm hergestellt werden;
ANMERKUNG Ronden mit einem Durchmesser von 1 000 mm können durch Stanzen (geschlossener Schnitt) her-gestellt werden.
- kalt- bzw. warmgewalztes Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einer Breite bis 1 600 mm;
Diese Norm gilt nicht für Butzen zum Fließpressen, die in einer besonderen Europäischen Norm behandelt werden.
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - Spécifications
La présente Norme européenne spécifie les exigences particulières applicables à l'aluminium et aux alliages d'aluminium corroyés sous forme de disques ou d'ébauches pour disques destinés à la fabrication d'ustensiles culinaires.
Elle s'applique aux :
- disques fabriqués à partir d'ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 12 mm inclus, et de diamètre compris entre 100 mm et 1 600 mm inclus.
NOTE Les disques dont le diamètre n'excède pas 1 000 mm peuvent être fabriqués par poinçonnage.
- ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 2 mm et 12 mm inclus et de largeur inférieure ou égale à 1 600 mm.
Elle ne s'applique pas aux pions de filage par choc, qui sont traités dans d'autres normes européennes.
Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih pripomočkov in posode - Specifikacije
Standard EN 851 določa posamezne zahteve za gneteni aluminij in aluminijeve zlitine v obliki rondel ali polizdelkov za uporabo pri izdelavi jedilnih pripomočkov in posode. Ta standard se uporablja za: - rondele, izdelane iz vroče ali hladno valjanih polizdelkov z debelino od 0,2 mm do vključno 12 mm in premerom od 100 mm do vključno 1 600 mm. – Vroče ali hladno valjane polizdelke z debelino od 2 mm do vključno 12 mm in premerom do vključno 1 600 mm. Ta evropski standard se ne uporablja za kovinske palice za udarno iztiskanje, ki so obravnavane v drugih evropskih standardih.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - SpezifikationenAluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - SpécificationsAluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:EN 851:2014SIST EN 851:2014en,fr,de01-julij-2014SIST EN 851:2014SLOVENSKI
STANDARDSIST EN 851:19981DGRPHãþD
SIST EN 851:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 851
April 2014 ICS 77.150.10 Supersedes EN 851:1995English Version
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - Spécifications
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - Spezifikationen This European Standard was approved by CEN on 13 March 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 851:2014 ESIST EN 851:2014
EN 851:2014 (E) 2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Technical conditions for inspection and delivery .5 4.1 General .5 4.2 Orders or tenders.5 5 Mechanical properties .6 5.1 General .6 5.2 Earing .6 6 Tolerances on dimensions and form .6 6.1 General .6 6.2 Diameter .6 6.3 Thickness .7 6.4 Tolerances on flatness for circle .7 6.5 Edge burr tolerances for circle .7 7 Other requirements.7 Bibliography . 12
SIST EN 851:2014
EN 851:2014 (E) 3 Foreword This document (EN 851:2014) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2014 and conflicting national standards shall be withdrawn at the latest by October 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 851:1995. With regard the previous version, Clause 2 Normative references was updated; no new alloys were added. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 851:2014
EN 851:2014 (E) 4 1 Scope This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications. This standard is applicable to: — Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm. NOTE Circles with a diameter up to 1 000 mm can be produced by blanking. — Hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm. This European Standard is not applicable to slugs for impact extrusions which are dealt with in other European Standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys – Sheet, strip and plate – Part 1: Technical conditions for inspection and delivery EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 circle circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a uniform thickness over 0,20 mm SIST EN 851:2014
EN 851:2014 (E) 5 3.2 circle stock flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils, sheets, or plate
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - SpezifikationenAluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - SpécificationsAluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:FprEN 851kSIST FprEN 851:2014en,fr,de01-februar-2014kSIST FprEN 851:2014SLOVENSKI
STANDARD
kSIST FprEN 851:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 851
September 2013 ICS 77.150.10 Will supersede EN 851:1995English Version
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - Spécifications
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - Spezifikationen This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 851:2013: EkSIST FprEN 851:2014
FprEN 851:2013 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Technical conditions for inspection and delivery . 5 4.1 General . 5 4.2 Orders or tenders . 5 5 Mechanical properties . 6 5.1 General . 6 5.2 Earing . 6 6 Tolerances on dimensions and form . 6 6.1 General . 6 6.2 Diameter . 6 6.3 Thickness . 7 6.4 Tolerances on flatness for circle . 7 6.5 Edge burr tolerances for circle . 7 7 Other requirements . 7 Bibliography. 12
kSIST FprEN 851:2014
FprEN 851:2013 (E) 3 Foreword This document (FprEN 851:2013) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 851:1995. With regard the previous version, Clause 2 Normative references was updated; no new alloys were added.
kSIST FprEN 851:2014
FprEN 851:2013 (E) 4 1 Scope This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This standard is applicable to: Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm. NOTE Circles with a diameter up to 1 000 mm may be produced by blanking. Hot or cold-rolled circle stock with a thickness from 2 mm up to and including 12 mm and with a width up to 1 600 mm.
This European Standard is not applicable to slugs for impact extrusions which are dealt with in other European Standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys – Sheet, strip and plate – Part 1: Technical conditions for inspection and delivery
EN 485-2, Aluminium and aluminium alloys – Sheet, strip and plate – Part 2: Mechanical properties
EN 485-3, Aluminium and aluminium alloys – Sheet, strip and plate – Part 3: Tolerances on dimensions and form for hot rolled products
EN 485-4, Aluminium and aluminium alloys – Sheet, strip and plate – Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys – Wrought products – Temper designations
EN 602, Aluminium and aluminium alloys – Wrought products – Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 circle circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a uniform thickness over 0,20 mm kSIST FprEN 851:2014
FprEN 851:2013 (E) 5 3.2 circle stock flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils, sheets, or plates, usually with sheared or sawn edges, and intended to be sawn, sheared or blanked into flat shapes to be subsequently formed, drawn, etc.
Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 hot rolled circle and circle stock circle or circle stock whose final thickness is obtained by hot rolli
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.