SIST EN 1106:2010

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Handbetätigte Einstellgeräte für GasgeräteRobinets à commande manuelle pour appareils utilisant les combustibles gazeuxManually operated taps for gas burning appliances27.060.20Plinski gorilnikiGas fuel burners23.060.99Drugi ventiliOther valvesICS:Ta slovenski standard je istoveten z:EN 1106:2010SIST EN 1106:2010en,fr,de01-november-2010SIST EN 1106:2010SLOVENSKI
STANDARDSIST EN 1106:20021DGRPHãþD



SIST EN 1106:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1106
May 2010 ICS 23.060.40 Supersedes EN 1106:2001English Version
Manually operated taps for gas burning appliances
Robinets à commande manuelle pour appareils à gaz
Handbetätigte Einstellgeräte für Gasgeräte This European Standard was approved by CEN on 29 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1106:2010: ESIST EN 1106:2010



EN 1106:2010 (E) 2 Contents Page Foreword .51Scope .62Normative references .63Terms and definitions .64Classification . 114.1Classes of control . 114.2Groups of taps . 124.3Classes of control functions . 125Units of measurement and test conditions . 126Construction requirements . 126.1General . 126.2Mechanical parts of the control . 126.2.1Appearance . 126.2.2Holes . 126.2.3Breather holes . 126.2.4Test for leakage of breather holes . 126.2.5Screwed fastenings . 126.2.6Jointing . 126.2.7Moving parts . 126.2.8Sealing caps . 126.2.9Dismantling and reassembly . 136.2.101Operating parts of taps . 136.3Materials . 136.3.1General material requirements . 136.3.2Housing . 136.3.3Test for leakage of housing after removal of non-metallic parts . 136.3.4Zinc alloys . 136.3.5Springs providing closing and/or sealing force . 136.3.6Resistance to corrosion and surface protection . 136.3.7Impregnation . 136.3.8Seals for glands for moving parts. 146.3.101Tap closure member . 146.4Gas connections . 146.5Electronic parts of the control . 146.6Protection against internal faults for the purpose of functional safety . 146.101Component parts . 146.101.1General . 146.101.2Turning angles . 146.101.2.1General . 146.101.2.2Opening at maximum flow . 156.101.2.3Opening at minimum flow . 156.101.2.4Single outlet tap . 156.101.3Lubrication . 156.101.4Stops . 156.101.5Safety lock . 156.101.6Bearing seal . 156.101.7Taper angle . 166.101.8Pre-setting devices . 166.101.9Open and closed position of a tap . 16SIST EN 1106:2010



EN 1106:2010 (E) 3 6.101.10Compensation means for taps . 166.101.11Spring effect in taps . 167Performance . 167.1General . 167.2Leak-tightness . 167.3Test for leak-tightness . 167.4Torsion and bending . 167.5Torsion and bending tests. 167.6Rated flow rate . 177.7Test for rated flow rate . 177.7.1Apparatus . 177.7.2Test procedure . 177.7.3Conversion of air flow rate . 177.8Durability . 177.9Performance tests for electronic controls . 177.10Long-term performance for electronic controls . 177.101Operating torque and force . 177.101.1Requirements for operating torque . 177.101.2Test for operating torque . 187.101.3Requirements for operating force . 187.101.4Test for operating force . 187.101.5Requirements for operating torque for safety lock . 187.101.6Test for operating torque for safety lock . 197.102Endurance . 197.102.1Requirement . 197.102.2Endurance test . 198EMC/Electrical requirements . 199Marking, installation and operating instructions . 209.1Marking . 209.2Installation and operating instructions . 209.3Warning notice . 20Annex A (normative)
Gas connections in common use in the various countries . 21Annex B (informative)
Leak-tightness test − volumetric method . 22Annex C (informative)
Leak-tightness test − pressure loss method . 23Annex D (normative)
Conversion of pressure loss into leakage rate . 24Annex E (normative)
Electrical/electronic component fault modes . 25Annex F (normative)
Additional requirements for safety accessories and pressure accessories as defined in EU Directive 97/23/EC . 26Annex G (normative)
Materials for pressurized parts . 27Annex H (informative)
Additional materials for pressurized parts . 28Annex I (normative)
Requirements for controls used in DC supplied gas burners and gas burning appliances . 29Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2009/142/EC relating to appliances burning gaseous fuels . 30Bibliography . 32 Figures Figure 1 — Taper plug tap . 7Figure 2 — Disc tap . 8SIST EN 1106:2010



EN 1106:2010 (E) 4 Figure 3 — Linear disc tap . 9Figure 4 — Parallel plug tap . 10Figure 5 — Needle valve . 11 Tables Table 1 — Marking . 14Table 2 — Maximum operating torque. 18Table 3 — Maximum operating force . 18Table ZA.1 — Correspondence between this European Standard and Directive 2009/142/EC relating to appliances burning gaseous fuels. 30 SIST EN 1106:2010



EN 1106:2010 (E) 5 Foreword This document (EN 1106:2010) has been prepared by Technical Committee CEN/TC 58 “Safety and control devices for burners and appliances burning gaseous or liquid fuels”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1106:2001. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document is intended to be used in conjunction with EN 13611:2007. This document refers to clauses of EN 13611:2007 or adapts clauses by stating "with the following modification", "with the following addition", "is replaced with the following" or "is not applicable" in the corresponding clause. This European Standard adds clauses or subclauses to the structure of EN 13611:2007 which are particular to this standard. It should be noted that these clauses and subclauses are not indicated as an addition. It should be noted that the following significant technical changes compared to the previous edition have been incorporated in this European Standard: a) scope is enlarged to maximum inlet pressures up to and including 50 kPa (500 mbar); b) alignment with EN 13611:2007; c) updating of Clause 2, Normative references; d) requirements from EN 126:2004 relating to "Open and closed position of a tap", "Compensation means for taps" and "Spring effect in taps" were included (refer to 6.101.9 to 6.101.11); e) requirements and tests relating to durability of elastomers in contact with gas (7.8 of this standard) are now totally aligned with EN 13611:2007, 7.8. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1106:2010



EN 1106:2010 (E) 6 1 Scope This European Standard specifies the safety, construction and performance requirements for manually operated taps and pre-setting taps intended for use with gas appliances and similar use, hereafter referred to as "taps".
This European Standard is applicable to taps with declared maximum inlet pressures up to and including 50 kPa (500 mbar) of nominal connection sizes up to and including DN 50 for use with one or more fuel gases in accordance with EN 437. This European Standard does not apply to manual operated shut-off valves conforming to EN 331. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13611:2007, Safety and control devices for gas burners and gas burning appliances — General requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13611:2007 and the following apply. 3.101 control tap direct or indirect manually operated devices with one or more
...