SIST EN 16776:2016
(Main)Resilient floor coverings - Homogeneous and heterogeneous polyurethane floor coverings - Specification
Resilient floor coverings - Homogeneous and heterogeneous polyurethane floor coverings - Specification
This European standard specifies the characteristics of resilient floor coverings based on polyurethane and modifications thereof supplied in either roll or tile form.
This specification does not apply for floor coverings that are specified in ISO 10582, ISO 24011, EN 1817 or EN 14565.
To encourage the consumer to make an informed choice, the standard includes a classification system (see ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking.
Elastische Bodenbeläge - Homogene und heterogene Polyurethan-Bodenbeläge - Spezifikation
Diese Europäische Norm legt die Eigenschaften für heterogene elastische Bodenbeläge ((TITEL+homogen?)) auf Basis von Polyurethan mit duroplastischen Eigenschaften fest, die als Rolle, Dielen oder in Plattenform geliefert werden. Diese Spezifikation gilt für Bodenbeläge, die aus einer Nutzschicht und weiteren, aus Polyurethan hergestellten kompakten Schichten bestehen, die sich in Zusammensetzung, chemischer Vernetzung und/oder im Design unterscheiden, und die eine Dekorschicht, Stabilisierungseinlage und eine sonstige Rückenschicht enthalten können.
Diese Spezifikation gilt nicht für Bodenbeläge, die in ISO 10582, ISO 24011, EN 1817 oder EN 14565 festgelegt sind.
Um den Verbraucher zu ermutigen, eine sachkundige Entscheidung zu treffen, enthält diese Norm ein Klassi¬fizierungssystem (siehe EN ISO 10874) auf Basis der Nutzungsintensität, das zeigt, wofür diese Bodenbeläge zufriedenstellend eingesetzt werden könnten. Die Norm legt auch die Anforderungen an die Kennzeichnung fest.
Revêtements de sol résilients - Revêtements homogènes et hétérogènes en polyuréthanne - Spécification
La présente Norme européenne spécifie les caractéristiques des revêtements de sol résilients hétérogènes à base de polyuréthanne et ayant des propriétés thermodurcissables fournis sous forme de rouleaux, de lames ou de dalles. La présente spécification s'applique aux revêtements de sol consistant en une couche d’usure et en une ou plusieurs autres couches compactes en polyuréthanne. Elles sont de composition et/ou de conception différentes, ont un taux de réticulation différent et peuvent contenir une couche décorative, une armature et un autre envers.
Elle ne s’applique pas aux revêtements de sol spécifiés dans les normes EN ISO 10582, EN ISO 24011, EN 1817 ou EN 14565.
Pour aider le consommateur à faire un choix éclairé, la présente norme inclut un système de classification (voir l'EN ISO 10874) basé sur l'intensité d'utilisation, qui indique les zones considérées pour l’usage de ces revêtements de sol. Elle prescrit également des exigences relatives au marquage.
Netekstilne talne obloge - Homogene in heterogene poliuretanske talne obloge - Specifikacija
Ta evropski standard določa lastnosti netekstilnih talnih oblog na osnovi poliuretana in njegovih sprememb, ki so na voljo v obliki plošč ali zvitkov. Ta specifikacija ne zajema talnih oblog, ki jih določa standard ISO 10582, ISO 24011, EN 1817 ali EN 14565. Da bi ta standard potrošnike spodbujal k sprejemanju utemeljenih odločitev, vključuje sistem razvrščanja (glej EN 10874) na podlagi intenzivnosti uporabe, ki kaže, kje bi se naj te talne obloge zadovoljivo uporabljale. Vključuje tudi zahteve za označevanje.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Netekstilne talne obloge - Homogene in heterogene poliuretanske talne obloge - SpecifikacijaElastische Bodenbeläge - Homogene und heterogene Polyurethan-Bodenbeläge - SpezifikationRevêtements de sol résilients - Revêtements homogènes et hétérogènes en polyuréthanne - SpécificationResilient floor coverings - Homogeneous and heterogeneous polyurethane floor coverings - Specification97.150Netekstilne talne oblogeNon-textile floor coveringsICS:Ta slovenski standard je istoveten z:EN 16776:2016SIST EN 16776:2016en,fr,de01-maj-2016SIST EN 16776:2016SLOVENSKI
STANDARD
SIST EN 16776:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16776
March
t r s x ICS
{ yä s w r English Version
Resilient floor coverings æ Heterogeneous polyurethane floor coverings æ Specification Revêtements de sol résilients æ Revêtements hétérogènes en polyuréthanne æ Spécification
Elastische Bodenbeläge æ Homogene und heterogene PolyurethanæBodenbeläge æ Spezifikation This European Standard was approved by CEN on
s r January
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x y y xã t r s x ESIST EN 16776:2016
EN 16776:2016 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Requirements . 5 5 Use and performance specification . 6 6 Marking . 7 Annex A (normative)
Method for test for resistance to scratching . 9 A.1 Introduction . 9 A.2 Principle . 9 A.3 Apparatus and materials . 9 A.4 Sampling and conditioning . 11 A.5 Procedure. 11 A.6 Evaluation . 12 A.7 Report . 12 A.8 Calibration of steel pins . 12 A.8.1 General . 12 A.8.2 Procedure. 12 A.8.3 Evaluation . 13 Annex B (informative)
Optional properties . 14 Bibliography . 15
SIST EN 16776:2016
EN 16776:2016 (E) 3 European foreword This document (EN 16776:2016) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by September 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 16776:2016
EN 16776:2016 (E) 4 1 Scope This European Standard specifies the characteristics of heterogeneous resilient floor coverings based on polyurethane with thermosetting properties supplied in either roll, planks or tile form. This specification does apply for floor covering consisting of a wear layer and other compact layers made from polyurethane which differ in composition, chemical crosslinking and/or design and can contain a decor layer, reinforcement and other backing. This specification does not apply for floor coverings that are specified in EN ISO 10582, EN ISO 24011, EN 1817 or EN 14565. To encourage the consumer to make an informed choice, the standard includes a classification system (see EN ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 424, Resilient floor coverings — Determination of the effect of simulated movement of a furniture leg EN 425, Resilient and laminate floor coverings — Castor chair test EN 1471, Textile floor coverings — Assessment of changes in appearance EN ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105-B02) EN ISO 291, Plastics — Standard atmospheres for conditioning and testing (ISO 291) EN ISO 10874, Resilient, textile and laminate floor coverings — Classification (ISO 10874) EN ISO 23997, Resilient floor coverings — Determination of mass per unit area (ISO 23997) EN ISO 23999, Resilient floor coverings — Determination of dimensional stability and curling after exposure to heat (ISO 23999) EN ISO 24340, Resilient floor coverings — Determination of thickness of layers (ISO 24340) EN ISO 24341, Resilient and textile floor coverings — Determination of length, width and straightness of sheet (ISO 24341) EN ISO 24342, Resilient and textile floor-coverings — Determination of side length, edge, straightness and squareness of tiles (ISO 24342) EN ISO 24343-1, Resilient and laminate floor coverings — Determination of indentation and residual indentation — Part 1: Residual indentation (ISO 24343-1) EN ISO 24344, Resilient floor coverings — Determination of flexibility and deflection (ISO 24344) EN ISO 24346, Resilient floor coverings — Determination of overall thickness (ISO 24346) ISO 11378-1, Textile floor coverings — Laboratory soiling tests — Part 1: Kappasoil test SIST EN 16776:2016
EN 16776:2016 (E) 5 ISO 16581, Resilient and laminate floor coverings — Determination of the effect of simulated movement of a furniture leg ASTM F1515, Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 wear layer layer of the floor covering directly exposed to wear Note 1 to entry: Binder content should be minimum 80 %. The binder content is consisting of polyurethane resin. 3.2 scratch permanent, visible surface damage of a physical nature 4 Requirements The requirements and test methods for floor coverings made from polyurethane are illustrated in Table 1. Table 1 — General requirements Characteristic Requirement Test method Roll form: length in m width in mm Not less than nominal values EN ISO 24341 Tiles: side length in mm Does not apply to planks squareness and straightness for side length: mm
400 mm > 400 mm Deviation
0,15 % of nominal length up to 0,5 mm maximum Deviation allowed at any point
0,25
0,35 EN ISO 24342 Overall thickness in mm - averagea
- individual results in mm - minimum overall thickness Nominal value + 0,13 - 0,10 Average valueb ± 0,15 1,20 mm EN ISO 24
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.