SIST EN ISO 5210:2017

SLOVENSKI STANDARD
01-julij-2017
1DGRPHãþD
SIST EN ISO 5210:2000
,QGXVWULMVNLYHQWLOL3ULNOMXþNLYUWLOQLKSRJRQRYQDYHQWLOLK,62
Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017)
Industriearmaturen - Anschlüsse von Drehantrieben für Armaturen (ISO 5210:2017)
Robinetterie industrielle - Raccordement des actionneurs multitours aux appareils de
robinetterie (ISO 5210:2017)
Ta slovenski standard je istoveten z: EN ISO 5210:2017
ICS:
23.060.01 Ventili na splošno Valves in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 5210
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2017
EUROPÄISCHE NORM
ICS 23.060.01 Supersedes EN ISO 5210:1996
English Version
Industrial valves - Multi-turn valve actuator attachments
(ISO 5210:2017)
Robinetterie industrielle - Raccordement des Industriearmaturen - Anschlüsse von Drehantrieben
actionneurs multitours aux appareils de robinetterie für Armaturen (ISO 5210:2017)
(ISO 5210:2017)
This European Standard was approved by CEN on 1 March 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5210:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 5210:2017) has been prepared by Technical Committee ISO/TC 153 “Valves” in
collaboration with Technical Committee CEN/TC 69 “Industrial valves” the secretariat of which is held
by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2017, and conflicting national standards shall
be withdrawn at the latest by October 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 5210:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5210:2017 has been approved by CEN as EN ISO 5210:2017 without any modification.
INTERNATIONAL ISO
STANDARD 5210
Second edition
2017-03
Industrial valves — Multi-turn valve
actuator attachments
Robinetterie industrielle — Raccordement des actionneurs multitours
aux appareils de robinetterie
Reference number
ISO 5210:2017(E)
©
ISO 2017
ISO 5210:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 5210:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Maximum torques and thrusts . 3
5 Flange dimensions . 4
6 Designation . 6
7 Dimensions of driving and driven components . 6
7.1 General . 6
7.2 Dimensions for assemblies capable of transmitting both torque and thrust: Group A . 6
7.3 Dimensions for assemblies capable of transmitting torque only: Group B . 8
7.4 Dimensions for assemblies capable of transmitting torque only: Group C . 9
7.5 Dimensions for assemblies capable of transmitting torque only: Group D .10
7.6 Dimensions for assemblies capable of transmitting thrust only: Group Linear actuators .11
Annex A (informative) Explanation of calculations .13
Bibliography .15
ISO 5210:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 153, Valves.
This second edition cancels and replaces the first edition (ISO 5210:1991), which has been technically
revised with the following changes:
a) extension of flange sizes;
b) introduction of groups C and D for assemblies capable of transmitting torque, in 7.4 and 7.5;
c) introduction of linear actuator in 7.6.
iv © ISO 2017 – All rights reserved

ISO 5210:2017(E)
Introduction
The purpose of this document is to establish certain basic requirements for the attachment of multi-
turn actuators, in order to define the interface between actuator and valve.
This document has, in general, to be considered in conjunction with the specific requirements which
may be agreed between the parties concerned.
INTERNATIONAL STANDARD ISO 5210:2017(E)
Industrial valves — Multi-turn valve actuator attachments
1 Scope
This document specifies the requirements for the attachment of multi-turn actuators to valves.
Throughout this document, “actuator” may be understood as “actuator and/or gearbox” providing a
multi-turn and/or linear output.
It specifies:
— flange dimensions necessary for the attachment of actuators to industrial valves [see Figure 1 a)] or
to intermediate supports [see Figure 1 b)];
— those driving component dimensions of actuators which are necessary to attach them to the driven
components;
— reference values for torque and thrust for flanges having the dimensions specified in this document.
NOTE 1 In this document, the term “valve” may also be understood to include “valve with an intermediate
support” [see Figure 1 b)].
NOTE 2 When a combination of a multi-turn actuator and separate multi-turn/linear gearbox is coupled to
form an actuator, the multi-turn attachment to the gearbox is in accordance with this document [see Figures 1 c)
and 1 d)]. A combination of a multi-turn actuator with integral multi-turn/linear gearbox supplied as an actuator
is in accordance with Figures 1 a) and 1 b).
ISO 5210:2017(E)
a)  Direct interface b)  Intermediate c)  Direct interface d)  Intermediate support
support interface   (when combination     interface (when
of a multi-turn     combination of a multi-
actuator and multi-     turn actuator and a
turn/linear     multi-turn/linear
gearbox)    gearbox)
Key
1 multi-turn/linear actuator 5 gearbox
2 interface (see ISO 5210) 6 interface (see ISO 5210)
3 valve 7 multi-turn actuator
4 intermediate support
Figure 1 — Interface between multi-turn/linear actuator and valve
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 273, Fasteners — Clearance holes for bolts and screws
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
2 © ISO 2017 – All rights reserved

ISO 5210:2017(E)
3.1
actuator
any device designed for attachment to a general purpose industrial valve in order to provide for the
operation of the valve
Note 1 to entry: The device
...