SIST EN 61058-1-1:2017/AC:2019
(Corrigendum)Switches for appliances - Part 1-1: Requirements for mechanical switches
Switches for appliances - Part 1-1: Requirements for mechanical switches
Geräteschalter - Teil 1-1: Anforderungen an mechanische Schalter
Interrupteurs pour appareils - Partie 1-1: Exigences relatives aux interrupteurs mécaniques
Stikala za aparate - 1-1. del: Zahteve za mehanske stikalne konstrukcije
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stikala za aparate - 1-1. del: Zahteve za mehanske stikalne konstrukcijeGeräteschalter - Teil 1-1: Anforderungen an mechanische SchalterInterrupteurs pour appareils - Partie 1-1: Exigences relatives aux interrupteurs mécaniquesSwitches for appliances - Part 1-1: Requirements for mechanical switches29.120.40StikalaSwitchesICS:Ta slovenski standard je istoveten z:EN
...
This May Also Interest You
- Amendment15 pagesEnglish languagesale 10% offe-Library read for×1 day
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for×1 day
- Corrigendum1 pageEnglish languagesale 10% offe-Library read for×1 day
This clause of Part 1 is completely replaced by the following:
This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons.
This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF.
Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices.
This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls).
The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed:
- intentionally by a person via an actuating member, a key, a card, etc., via a sensing
surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal;
- by physical means, for example, light, temperature, humidity, time, wind velocity, presence
of people;
- by any other influence.
This document also applies to electronic control devices which include integrated radio receivers and transmitters.
This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices.
Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670.
This document is not intended to cover devices falling within the scope of IEC 60730 (all parts).
Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of −5 °C.
NOTE 1 For lower temperatures, see Annex E.
Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices.
In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required.
This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1.
Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA.
Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC.
Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE.
NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.
- Standard139 pagesEnglish languagesale 10% offe-Library read for×1 day
- 21-Apr-2019
- 10-Apr-2023
- 29.120.40
- 97.120
- 2014/30/EU
- 2014/35/EU
- 2014/53/EU
- M/511
- M/536
- M/552
- EPR
To give requirements and tests for electronic control devices, a general term to cover electronic switches, HBES/BACS switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC.
This Part of IEC 60669 also applies to electronic control devices which include integrated radio receivers and transmitters.
- Amendment10 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Apr-2022
- 06-Apr-2023
- 29.120.40
- 97.120
- 2014/30/EU
- 2014/35/EU
- 2014/53/EU
- M/511
- M/536
- M/552
- EPR
IEC 61058-2-5:2018 is available as IEC 61058-2-5:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61058-2-5:2018 applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- updated references due to new structure of IEC 61058-1;
- changes on conducting the heating test due to the corresponding changes in IEC 61058-1.
- Standard13 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61058-2-1:2018 applies to cord switches (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A.
This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
Overall format to support IEC 61058-1, IEC 61058-1-1, IEC 61058-1-2, and the heating tests.
- Standard26 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61058-2-4:2018 is available as IEC 61058-2-4:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61058-2-4:2018 applies to independently mounted switches for appliances (mechanical or electronic) actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This second edition cancels and replaces the first edition published in 1995 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- overall format modified to support the revised structure of the series;
- Annexes K and M have been included as an integral part of this document;
- Annex L has been included for information purposes only.
This document is to be used in conjunction with IEC 61058-1:2016.
- Standard23 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 63180:2020 provides a methodology and test procedures to be able to declare and verify the detection area for motion detectors using passive infrared technology in electronic control devices and appliance switches, whether stand-alone (direct control of one or more applications) or as part of home and building electronic systems or building automation control systems (HBES/BACS) or similar.
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
TAN - // IEC Corrigendum
- Corrigendum6 pagesEnglish and French languagesale 10% offe-Library read for×1 day
- 09-Jun-2020
- 29.120.40
- 2014/35/EU
- M/511
- EPR
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...