SIST EN 62442-2:2014

SLOVENSKI STANDARD
SIST EN 62442-2:2014
01-september-2014
(QHUJLMVNDXþLQNRYLWRVWNUPLOQLKQDSUDY]DVLMDONHGHO.UPLOQHQDSUDYH]D
YLVRNRLQWHQ]LYQRVWQHUD]HOHNWULWYHQHVLMDONHUD]HQIOXRUHVFHQþQHVLMDONH0HULOQD
PHWRGD]DXJRWDYOMDQMHXþLQNRYLWRVWLNUPLOQLKQDSUDY
Energy performance of lamp controlgear - Part 2: Controlgear for high intensity discharge
lamps (excluding fluorescent lamps) - Method of measurement to determine the
efficiency of controlgear
/
Performance énergétique des appareillages de lampes - Partie 2: Appareillages des
lampes à décharge à haute intensité (à l’exclusion des lampes à fluorescence) -
Méthode de mesure pour la détermination du rendement des appareillages
Ta slovenski standard je istoveten z: EN 62442-2:2014
ICS:
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST EN 62442-2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62442-2:2014

---------------------- Page: 2 ----------------------

SIST EN 62442-2:2014


EUROPEAN STANDARD EN 62442-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2014
ICS 29.140.99

English Version
Energy performance of lamp controlgear - Part 2: Controlgear for
high intensity discharge lamps (excluding fluorescent lamps) -
Method of measurement to determine the efficiency of the
controlgear
(IEC 62442-2:2014)
Performance énergétique des appareillages de lampes - Energieeffizienz von Lampenbetriebsgeräten - Teil 2:
Partie 2: Appareillages des lampes à décharge à haute Betriebsgeräte für Hochdruck-Entladungslampen
intensité (à l'exclusion des lampes à fluorescence) - (ausgenommen Leuchtstofflampen) - Messverfahren zur
Méthode de mesure pour la détermination du rendement Bestimmung des Wirkungsgrades von Betriebsgeräten
des appareillages (IEC 62442-2:2014)
(CEI 62442-2:2014)
This European Standard was approved by CENELEC on 2014-05-22. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62442-2:2014 E

---------------------- Page: 3 ----------------------

SIST EN 62442-2:2014
EN 62442-2:2014 - 2 -

Foreword
The text of document 34C/1078/FDIS, future edition 1 of IEC 62442-2, prepared by SC 34C
"Auxiliaries for lamps" of IEC/TC 34 "Lamps and related equipment" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN 62442-2:2014.

The following dates are fixed:
• latest date by which the document has (dop) 2015-02-22
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-05-22
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 62442-2:2014 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60188 NOTE Harmonised in EN 60188 (not modified).
IEC 60662 NOTE Harmonised in EN 60662 (not modified).
IEC 60923 NOTE Harmonised in EN 60923 (not modified).
IEC 61167 NOTE Harmonised in EN 61167 (not modified).
IEC 62035 NOTE Harmonised in EN 62035 (not modified).
IEC 62442-1:2011 NOTE Harmonised in EN 62442-1:2011 (not modified).
IEC 62442-3 NOTE Harmonised in EN 62442-3 (not modified).

---------------------- Page: 4 ----------------------

SIST EN 62442-2:2014
- 3 - EN 62442-2:2014

Annex ZA
(normative)


Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu

Publication Year Title EN/HD Year

IEC 61347-1 (mod) 2007 Lamp controlgear -- EN 61347-1 2008
Part 1: General and safety requirements
+A1 2010  +A1 2011
+A2 2012  +A2 2013
IEC 61347-2-9 2012 Lamp controlgear -- EN 61347-2-9 2013
Part 2-9: Particular requirements for
electromagnetic controlgear for discharge
lamps (excluding fluorescent lamps)
IEC 61347-2-12 2010 Lamp controlgear - - -
Part 2-12: Particular requirements for d.c.
or a.c. supplied electronic ballasts for
discharge lamps (excluding fluorescent
lamps)
IEC Guide 115  Application of uncertainty of measurement - -
to conformity assessment activities in the
electrotechnical sector

---------------------- Page: 5 ----------------------

SIST EN 62442-2:2014

---------------------- Page: 6 ----------------------

SIST EN 62442-2:2014



IEC 62442-2

®


Edition 1.0 2014-04




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Energy performance of lamp controlgear –

Part 2: Controlgear for high intensity discharge lamps (excluding fluorescent

lamps) – Method of measurement to determine the efficiency of the controlgear




Performance énergétique des appareillages de lampes –

Partie 2: Appareillages des lampes à décharge à haute intensité (à l’exclusion


des lampes à fluorescence) – Méthode de mesure pour la détermination du

rendement des appareillages












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX M


ICS 29.140.99 ISBN 978-2-8322-1529-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62442-2:2014
– 2 – IEC 62442-2:2014 © IEC 2014
CONTENTS

FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions. 6
4 General . 7
4.1 Applicability . 7
4.2 General notes on test . 7
4.3 Controllable controlgear . 7
4.4 Multi-lamp type controlgear . 7
4.5 Measurement uncertainty . 8
4.6 Sampling of controlgear for testing . 8
4.7 Number of samples . 8
4.8 Power supply. 8
4.9 Supply voltage waveform . 8
4.10 Instrument accuracy . 8
4.11 Multi-rated voltage controlgear . 9
5 Method of measurement of the input power and calculation of the efficiency of
controlgear for high intensity discharge lamps . 9
5.1 Measurement setup: Electromagnetic wire wound controlgear . 9
5.2 Efficiency calculation: Magnetic wire wound controlgear . 10
5.3 Measurement setup: Electronic controlgear . 10
5.4 Efficiency calculation: Electronic controlgear . 11
5.5 Standby power measurement of electronic controlgear . 11
Bibliography . 13

Figure 1 – Measurement setup for electromagnetic controlgear . 9
Figure 2 – Measurement setup for electronic controlgear . 10
Figure 3 – Measurement setup of the standby power of electronic controlgear . 11

Table 1 – Typical nominal electricity supply details for some regions . 8

---------------------- Page: 8 ----------------------

SIST EN 62442-2:2014
IEC 62442-2:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ENERGY PERFORMANCE OF LAMP CONTROLGEAR –

Part 2: Controlgear for high intensity discharge lamps
(excluding fluorescent lamps) – Method of measurement
to determine the efficiency of the controlgear


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62442-2 has been prepared by subcommittee 34C: Auxiliaries for
lamps, of IEC technical committee 34: Lamps and related equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
34C/1078/FDIS 34C/1089/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------

SIST EN 62442-2:2014
– 4 – IEC 62442-2:2014 © IEC 2014
A list of all parts of the IEC 62442 series, published under the general title Energy performance
of lamp controlgear, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------

SIST EN 62442-2:2014
IEC 62442-2:2014 © IEC 2014 – 5 –
ENERGY PERFORMANCE OF LAMP CONTROLGEAR –

Part 2: Controlgear for high intensity discharge lamps
(excluding fluorescent lamps) – Method of measurement
to determine the efficiency of the controlgear



1 Scope
This part of the IEC 62442 series defines a measurement method of the power losses of
...