iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60512-21-1:2010

Connectors for electronic equipment - Tests and measurements - Part 21-1: R.F. resistance tests - Test 21a: R.F. shunt resistance (IEC 60512-21-1:2010)

Connectors for electronic equipment - Tests and measurements - Part 21-1: R.F. resistance tests - Test 21a: R.F. shunt resistance (IEC 60512-21-1:2010)

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to determine the value of RF shunt resistance which degrades the quality factor of an L/C circuit when a connector is connected in parallel. This value is expressed in terms of a parallel damping resistance.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 21-1: Prüfungen der HF-Güte - Prüfung 21a: HF-Dämpfungswiderstand (IEC 60512-21-1:2010)

Connecteurs pour équipements électroniques - Essais et mesures - Partie 21-1: Essais de résistance aux fréquences radioélectriques - Essai 21a: Résistance parallèle aux fréquences radioélectriques (CEI 60512-21-1:2010)

La CEI 60512-21-1:2010 est utilisée pour les essais des connecteurs du domaine d'activité du comité d'études 48, lorsque la spécification particulière l'exige. Elle peut également être utilisée pour des dispositifs similaires lorsqu'une spécification particulière le stipule. L'objet de cette norme est de définir une méthode d'essai normalisée pour déterminer la valeur de la résistance parallèle aux fréquences radioélectriques qui dégrade le facteur de qualité d'un circuit L/C lorsqu'un connecteur est raccordé en parallèle. Cette valeur est exprimée en termes d'une résistance parallèle d'amortissement.

Konektorji za elektronsko opremo - Preskusi in meritve - 21-1. del: Preskusi odpornosti proti radijskim frekvencam - Preskus 21a: Odpornost proti vzporedni radijski frekvenci (IEC 60512-21-1:2010)

Ta del IEC 60512, kadar ga zahteva podrobna specifikacija, se uporablja za preskušanje konektorjev v okviru tehničnega odbora 48. Lahko se uporablja tudi za podobne naprave, kadar ga določa podrobna specifikacija. Cilj tega standarda je podrobno opredeliti standardno preskusno metodo za določevanje vrednost odpornosti proti vzporedni radijski frekvenci, ki zmanjšuje dejavnik kakovosti toka L/C, kadar je konektor povezan vzporedno. Ta vrednost je izražena glede na vzporedno dušilno odpornostjo.

General Information

Status
Published
Publication Date
22-Jul-2010
ICS
31.220.10 - Plug-and-socket devices. Connectors
Technical Committee
I11 - Imaginarni 11
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Jul-2010
Due Date
18-Sep-2010
Completion Date
23-Jul-2010
Ref Project
EN 60512-21-1:2010 - Connectors for electronic equipment - Tests and measurements - Part 21-1: R.F. resistance tests - Test 21a: R.F. shunt resistance

Buy Standard

EN 60512-21-1:2010EN 60512-21-1:2010
PreviousNext
Standard
EN 60512-21-1:2010
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60512-21-1:2010
01-september-2010
Konektorji za elektronsko opremo - Preskusi in meritve - 21-1. del: Preskusi
odpornosti proti radijskim frekvencam - Preskus 21a: Odpornost proti vzporedni
radijski frekvenci (IEC 60512-21-1:2010)
Connectors for electronic equipment - Tests and measurements - Part 21-1: R.F.
resistance tests - Test 21a: R.F. shunt resistance (IEC 60512-21-1:2010)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 21-1:
Prüfungen der HF-Güte - Prüfung 21a: HF-Dämpfungswiderstand (IEC 60512-21-
1:2010)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 21-1: Essais
de résistance aux fréquences radioélectriques - Essai 21a: Résistance parallèle aux
fréquences radioélectriques (CEI 60512-21-1:2010)
Ta slovenski standard je istoveten z: EN 60512-21-1:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60512-21-1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60512-21-1:2010

---------------------- Page: 2 ----------------------

SIST EN 60512-21-1:2010

EUROPEAN STANDARD
EN 60512-21-1

NORME EUROPÉENNE
July 2010
EUROPÄISCHE NORM

ICS 31.220.01


English version


Connectors for electronic equipment -
Tests and measurements -
Part 21-1: R.F. resistance tests -
Test 21a: R.F. shunt resistance
(IEC 60512-21-1:2010)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Essais et mesures - Mess- und Prüfverfahren -
Partie 21-1: Essais de résistance Teil 21-1: Prüfungen der HF-Güte -
aux fréquences radioélectriques - Prüfung 21a: HF-Dämpfungswiderstand
Essai 21a: Résistance parallèle (IEC 60512-21-1:2010)
aux fréquences radioélectriques
(CEI 60512-21-1:2010)




This European Standard was approved by CENELEC on 2010-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-21-1:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60512-21-1:2010
EN 60512-21-1:2010 - 2 -
Foreword
The text of document 48B/2151/FDIS, future edition 1 of IEC 60512-21-1, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-21-1 on 2010-07-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-07-01
__________
Endorsement notice
The text of the International Standard IEC 60512-21-1:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60512-21-1:2010
IEC 60512-21-1
®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Connectors for electronic equipment – Tests and measurements –
Part 21-1: RF resistance tests – Test 21a: RF shunt resistance

Connecteurs pour équipements électroniques – Essais et mesures –
Partie 21-1: Essais de résistance aux fréquences radioélectriques – Essai 21a:
Résistance parallèle aux fréquences radioélectriques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
D
CODE PRIX
ICS 31.220.01 ISBN 978-2-88910-954-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------

SIST EN 60512-21-1:2010
– 2 – 60512-21-1 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –

Part 21-1: RF resistance tests –
Test 21a: RF shunt resistance


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning stan
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 61076-2-115:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-115: Circular connectors - Detail specification for 12-pole connectors with 2 A rated current and push-pull locking IP65/IP67 with metal housing (IEC 61076-2-115:2023)
EN IEC 61076-2-115:2023

IEC 61076-2-115:2023 describes free and fixed 12P shielded circular connectors with 2 A rated current, rated voltage up to and including 50 V AC/DC, IP65/IP67 metal housing with push-pull locking (hereinafter referred to as a connectors) for use in electrical and electronic equipment. It includes overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61076-3-126:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 3-126: Rectangular connectors - Detail specification for 5-way power connector for industrial environments with push-pull locking (IEC 61076-3-126:2023)
EN IEC 61076-3-126:2023

IEC 61076-3-126:2023 covers 5-pole rectangular connectors for electric power supply up to 16 A per pole. These connectors consist of fixed and free connectors, both either rewirable or non-rewirable. This document employs the general function principles of the push-pull connector housing system described in IEC 61076‑3‑117 with IP65/IP67 degree of protection according to IEC 60529 for harsh applications.
Male connectors have pin contacts with square cross-section with 1 mm side. Connectors according to this document are without breaking capacity COC according to IEC 61984, therefore they are not intended to be engaged or disengaged in normal use when live or under load.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61076-2-116:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-116: Detail specification for circular connectors size 15 with up to 3+PE power contacts and auxiliary contacts, with bayonet-locking (IEC 61076-2-116:2022)
EN IEC 61076-2-116:2023

IEC 61076-2-116:2022 specifies circular connectors size 15 with bayonet-locking, with up to 3 power contacts with rated insulation voltage up to 630 V AC/DC and rated current up to 20 A, plus PE, and up to 3 auxiliary contacts with rated insulation voltage up to 63 V AC/DC and rated current up to 10 A, that are typically used for industrial power supply and power applications, such as the feeding and control of 3-phase asynchronous motors. These connectors consist of both fixed and free connectors either rewireable or non-rewireable, with bayonet-locking. Male connectors have round contacts, either power or signal, Ø1,6 mm.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60512-27-200:2022(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 27-200: Additional specifications for signal integrity tests up to 2 000 MHz on IEC 60603-7 series connectors - Tests 27a to 27g (IEC 60512-27-200:2022)
EN IEC 60512-27-200:2022

This part of IEC 60512 covers additional, supplemental test method specifications to extend the
upper frequency for the test connectors and associated indirect-reference test fixtures used in
the signal integrity and transmission performance tests specified in IEC 60512-27-100. In
support of de-embedded crosstalk and related transmission requirements specified in
IEC 60603-7-81, for frequencies up to 2 000 MHz, these supplemental specifications extend
the upper test frequency from IEC 60512-27-100 up to 500 MHz to the upper test frequency of
IEC 60512-28-100 up to 2 000 MHz.
This document covers measurements of connector signal integrity and transmission
performance of 8-way connector types defined in these published connector series standards:
IEC 60603-7-2
IEC 60603-7-3
IEC 60603-7-4
IEC 60603-7-5
IEC 60603-7-41
IEC 60603-7-51
IEC 60603-7-81.
This document covers respective performance test procedures of connector signal integrity and
transmission performance defined in these published connector test method series standards:
IEC 60512-26-100
IEC 60512-27-100
IEC 60512-28-100.
These additional specifications are also suitable for testing the series related lower frequency
backward compatible connectors. However, the actual measurement or test procedure specified
in the detail specification for any particular connector remains the reference conformance test
for that connector category; see Table 1.
The test procedures of IEC 60512-27-100 affected by these supplemental specifications are:
– insertion loss, test 27a;
– return loss, test 27b;
– near-end crosstalk (NEXT) test 27c;
– far-end crosstalk (FEXT), test 27d;
– transverse conversion loss (TCL), test 27f;
– transverse conversion transfer loss (TCTL), test 27g.
– transfer impedance (ZT), see IEC 60512-26-100, test 26e.
– 8 – IEC 60512-27-200:2022 © IEC 2022
– coupling attenuation (aC), see IEC 62153-4-12.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63171-5:2022(Main)
Connectors for electrical and electronic equipment - Part 5: Detail specification for 2-way M8 and M12 circular connectors, shielded or unshielded, free and fixed - Mechanical mating information, pin assignment and additional requirements for Type 5 (IEC 63171-5:2022)
EN IEC 63171-5:2022

This part of IEC 63171 describes shielded or unshielded circular connectors with 2 ways and M8 or M12 Styles, typically used for data transmission up to 600 MHz and with current carrying capacity up to 4 A, for use in areas with harsh environmental conditions. These connectors consist of fixed and free connectors either rewirable or non-rewirable. Male connectors have square cross- section contacts, for data and power transmission.
M12 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-101 of this size of circular connectors. M8 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-104. The use of alternative locking mechanisms according to IEC 61076-2-010 or IEC 61076-2-011 are possible.
The coding provided by this standard prevents the mating of accordingly coded male or female connectors to other similarly sized interfaces covered by this or other standards.
These Type 5 connectors are interoperable with Type 2 connectors according IEC 63171-2, except the locking and sealing system provided by the outer shell.
The shielded and unshielded connectors are interoperable for their internal transmission performance and can be exchanged. The shielded version has improved EMC and coupling properties.
This part of IEC 63171 covers Type 5 connectors. Each part of this series has the associated type number equal to the number of the part in the series. All connectors in the IEC 63171 series are deemed to provide the same functions as defined in IEC 63171:2021, using different mechanical interfaces.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60512-99-002:2022(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 99-002: Endurance test schedules - Test 99b: Test schedule for unmating under electrical load (IEC 60512-99-002:2022)
EN IEC 60512-99-002:2022

This part of IEC 60512 is used for the assessment of connectors within the scope of SC 48B
that are used in twisted pair communication cabling with remote power, such as
ISO/IEC 11801-1 Class D, or better, balanced cabling in support of IEEE 802.3btTM (Power over
Ethernet, supporting up to 90 W from the power sourcing equipment).
The object of this document is to detail a test schedule to determine the ability of sets of
connectors to withstand a minimum of 100 mechanical operations with electrical load, where an
electrical current is being passed through the connectors in accordance with IEC 60512-9-3
during the separation (unmating) step.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61076-2-011:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-011: Circular connectors - Detail specification for B12 bayonet coupling connectors based on mating interfaces according to IEC 61076-2-101 and IEC 61076-2-109 (IEC 61076-2-011:2021)
EN IEC 61076-2-011:2021

This part of IEC 61076-2 describes the bayonet coupling interface of circular connectors that
are typically used for industrial process measurement and control. These connectors consist of
fixed and free connectors either rewireable or non-rewireable, with bayonet-coupling. These
connectors may have glass to metal seal inserts. They have male or female contacts and are
deemed to be intermateable with corresponding free connectors produced according to this
document. Male connectors have round contacts Ø 0,6 mm, Ø 0,76 mm, Ø 0,8 mm and
Ø 1,0 mm.
Different codings prevent the mating of these individually coded fixed connectors (and
consequently of individually coded free connectors deemed to couple with them) to other
interfaces and cross-mating between the different codings. However, the styles and interface
dimensions, except for the coupling mechanism, are as given in 4.3 of IEC 61076-2- 101:2012
and 4.3.1 of IEC 61076-2-109:2014.
The male type B12 circular connectors are interoperable with the female type B12 connector of
the same coding and ways. The female type B12 connectors are interoperable with the male
type B12 and M12 (threaded screw coupling) connector of the same coding and ways.
NOTE B12 relates to a bayonet coupling with tube dimensions compatible with a M12 thread. M12 is the dimension
of the thread of the screw-coupling mechanism of circular connectors covered by IEC 61076-2-101 and
IEC 61076-2-109, which provide the mating interface (connector insert level) to these connectors with bayonet
coupling.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61076-2-010:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for connectors with outer or inner push-pull locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-010:2021)
EN IEC 61076-2-010:2021

This part of IEC 61076-2 specifies circular connectors with a push-pull locking mechanism of a size derived from, and thus being compatible with M12 screw-locking connectors (free connectors with screw-locking according to IEC 61076‑2‑101, IEC 61076-2-109,
IEC 61076-2-111 or IEC 61076‑2‑113 are compatible with push‑pull fixed interfaces according
to this document) and with mating interfaces according to IEC 61076‑2‑101, IEC 61076-2-109,
IEC 61076-2-111 (except codings E in general and coding F for inner push-pull) or
IEC 61076-2-113.
A fixed connector with push-pull locking according to this document is intermateable with a
correspondingly coded free connector with M12 screw-locking according to any of the above
mentioned standards.
NOTE 1 M12 is the dimension of the thread of the screw-locking mechanism of circular connectors with M12 screwlocking.
NOTE 2 IEC 61076-2-012 defines another inner push-pull for fixed female connectors which is however not
compatible to the inner push-pull defined in this document. Annex C shows the different styles of female free
connectors to extend male free connectors.
This document covers both:
a) power connectors with current ratings up to 16 A and voltage ratings up to 630 V, typically
used for power supply and power applications in industrial premises, and
b) connectors for data and signal transmission with frequencies up to 500 MHz.
These connectors consist of both, fixed and free connectors, either rewirable or non-rewirable,
with M12 push-pull locking as explained above. Male connectors have round contacts from Ø
0,6 mm up to Ø 1,5 mm. In addition, the push-pull mechanisms consist of 2 different push-pull
designs:
c) An outer push-pull for male and female fixed connector, where the locking groove is placed
onto the outer cylindric surface of the housing. The outer push-pull for female fixed
connectors is made for 2 different types of male connectors. It has locking means for both
types on its outer surface.
NOTE 3 For design and dimensions see 5.3.2 and 5.3.3.
d) An inner push-pull for female fixed connectors and for male free connectors, where the
locking means are placed onto the inner cylindric surface of the housing.
NOTE 4 For design and dimensions see 5.3.4.
The different codings provided by IEC 61076-2 series detail specifications mentioned within this
document prevent the mating of accordingly coded male or female connectors to any other
similarly sized interfaces, covered by other standards and the cross-mating between the
different codings provided by any other IEC 61076-2 series detail specification mentioned within
this document.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61076-3-122:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and data transmission with frequencies up to 500 MHz and current-carrying capacity in industrial environments (IEC 61076-3-122:2021)
EN IEC 61076-3-122:2021

This part of IEC 61076 covers 8-way, shielded, free and fixed rectangular connectors for I/O
and data transmission with frequencies up to 500 MHz. It is intended to specify the common
dimensions, mechanical, electrical and environmental characteristics and tests for this family
of connectors.
Connectors complying with this document provide an ingress protection level of IP20; however,
they are particularly suited for industrial environments with a high level of vibration.
NOTE 1 In terms of the MICE system as defined in ISO/IEC 11801-1, the connector matches the requirements of
the M3I1C3E3 levels.
There are two classes of connectors defined in this document, indicated by "class A" and
"class B" which are distinguished by some electrical and mechanical characteristics to meet the
particular sets of requirements of some industrial applications.
NOTE 2 Class A meets the requirements defined in Ed.1 of this document.
NOTE 3 With the two classes A and B, the two codings Type I and II, and the two sets of transmission requirements
according to the component categories Cat 5 and Cat 6A as defined in ISO/IEC 11801-1, this document specifies
2 × 2 × 2 = 8 variants.
All connectors covered by this document feature a current-carrying capacity beyond the
minimum requirement of 0,75 A per pin for an ambient temperature of 60° C as defined in
ISO/IEC 11801-1.
NOTE 4 The current-carrying capacity is given by the current-temperature derating defined in this document and is
dependent on the wire size of the cable attached to the connector.
NOTE 5 With a current-carrying capacity of 0,5 A per pin and with matching the requirement of withstanding the
test current of 2 A for unmating under load as defined in IEC 60512-99-002, the connectors covered by this document
support the highest Power over Ethernet level as defined by IEEE 802.3bt (100 W PoE++ Type 4).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63171:2021(Main)
Connectors for electrical and electronic equipment - Shielded or unshielded free and fixed connectors for balanced single-pair data transmission with current-carrying capacity - General requirements and tests (IEC 63171:2021)
EN IEC 63171:2021

This document covers shielded and unshielded free and fixed connectors, circular or
rectangular, for balanced single-pair data transmission, with current-carrying capacity.
It specifies the IEC 63171 series' common mechanical, electrical and transmission
characteristics and environmental requirements, as well as required test specifications.
This document does not describe a specific mating interface. Detail specifications of mating
interfaces complying with this document can be found in the family of detail specification
standards IEC 63171-X (type X).
Within their own type, the shielded and unshielded connectors are interoperable for their
transmission performance and can be exchanged; though the shielded version has improved
alien crosstalk and coupling attenuation properties.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day