oSIST prEN 15427-1-1:2020
(Main)Railway applications - Wheel/Rail friction management - Part 1-1: Equipment and Application - Flange Lubricants
Railway applications - Wheel/Rail friction management - Part 1-1: Equipment and Application - Flange Lubricants
This European standard specifies the requirements when applying lubricant to the interface between the wheel flange and the rail (active interface) either directly or indirectly to the wheel flange or to the rail and includes both trainborne and trackside solutions.
This standard only covers the equipment and application of lubricant to the active interface.
This document defines:
- the characteristics that systems of lubrication of the wheel-rail interface shall achieve, together with applicable inspection and test methods to be carried out for verification;
- all relevant terminology which is specific to the lubrication of the wheel-rail interface.
This document only applies to the mainline railway
NOTE This document can also be used for other railways, e. g urban rail.
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 1-1: Vorrichtungen und Anwendung - Spurkranzschmierung
Applications ferroviaires - Gestion des frottements roue/rail - Partie 1-1 : Équipement et application - Lubrification des boudins de roues
Železniške naprave - Trenje na stiku kolo-tirnica - 1-1. del: Oprema in uporaba - Maziva za prirobnice
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
oSIST prEN 15427-1-1:2020
01-december-2020
Železniške naprave - Trenje na stiku kolo-tirnica - 1-1. del: Oprema in uporaba -
Maziva za prirobniceRailway applications - Wheel/Rail friction management - Part 1-1: Equipment and
Application - Flange Lubricants
Bahnanwendungen - Reibungsmanagement zwischen Rad und Schiene - Teil 1-1:
Vorrichtungen und Anwendung - Spurkranzschmierung
Applications ferroviaires - Gestion des frottements roue/rail - Partie 1-1 : Équipement et
application - Lubrification des boudins de rouesTa slovenski standard je istoveten z: prEN 15427-1-1
ICS:
21.260 Mazalni sistemi Lubrication systems
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
oSIST prEN 15427-1-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN 15427-1-1:2020
---------------------- Page: 2 ----------------------
oSIST prEN 15427-1-1:2020
DRAFT
EUROPEAN STANDARD
prEN 15427-1-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2020
ICS 21.260; 45.040 Will supersede EN 15427:2008+A1:2010
English Version
Railway applications - Wheel/Rail friction management -
Part 1-1: Equipment and Application - Flange Lubricants
Applications ferroviaires - Gestion des frottements Bahnanwendungen - Reibungsmanagement zwischen
roue/rail - Partie 1-1 : Équipement et application - Rad und Schiene - Teil 1-1: Vorrichtungen und
Lubrification des boudins de roues Anwendung - SpurkranzschmierungThis draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 256.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15427-1-1:2020 E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
Contents Page
European foreword .................................................................................................................................. 4
Introduction ............................................................................................................................................... 5
1 Scope ............................................................................................................................................... 6
2 Normative references ............................................................................................................... 6
3 Terms and definitions .............................................................................................................. 6
4 General ........................................................................................................................................... 7
4.1 Purpose of equipment .............................................................................................................. 7
4.2 Application of lubricant ........................................................................................................... 7
5 Requirements for trainborne equipment .......................................................................... 8
5.1 General ........................................................................................................................................... 8
5.2 Design of trainborne equipment .......................................................................................... 8
5.3 Installation of trainborne equipment ................................................................................. 9
5.4 Operations, Inspection and maintenance .......................................................................... 9
5.5 Application ................................................................................................................................. 10
5.6 Verification ................................................................................................................................ 10
6 Requirements for trackside equipment .......................................................................... 11
6.1 General ........................................................................................................................................ 11
6.2 Design of trackside equipment........................................................................................... 11
6.3 Installation of trackside equipment ................................................................................. 12
6.4 Operations, Inspection and maintenance ....................................................................... 12
6.5 Application ................................................................................................................................. 12
6.6 Verification ................................................................................................................................ 13
Annex A (informative) Types of trainborne and trackside equipment ............................ 14
A.1 Introduction .............................................................................................................................. 14
A.2 Trainborne Equipment.......................................................................................................... 14
A.3 Trackside Equipment ............................................................................................................. 14
Annex B (informative) Guidance on approvals testing and verification .......................... 15
B.1 General ........................................................................................................................................ 15
B.2 System – Equipment and lubricants ................................................................................. 16
Annex C (informative) Lubricant product performance - Field assessment ................... 17
C.1 General ........................................................................................................................................ 17
C.2 Product performance assessment ..................................................................................... 17
C.3 Monitoring ................................................................................................................................. 18
C.4 Outcome of trial ....................................................................................................................... 18
Annex D (informative) Guidance on verification and optimization of the application
system .......................................................................................................................................... 19
D.1 General ........................................................................................................................................ 19
---------------------- Page: 4 ----------------------oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
D.2 Trainborne equipment.......................................................................................................... 19
D.3 Trackside equipment ............................................................................................................. 19
D.4 Assessing the lubrication condition of rail or wheel (adhesive tapeimpression) ............................................................................................................................... 20
Annex E (informative) Installation and maintenance good practice for trainborneequipment .................................................................................................................................. 23
E.1 Reasons for installing trainborne equipment .............................................................. 23
E.2 Positioning of Applicator ...................................................................................................... 23
E.3 Information for maintenance of spray nozzles ............................................................ 25
E.4 Information for maintenance of spray nozzles ............................................................ 25
Annex F (informative) Installation and maintenance good practice for tracksideequipment .................................................................................................................................. 27
F.1 Selecting locations for trackside equipment ................................................................. 27
F.2 Determination of Lubricant Application Unit position ............................................. 27
F.3 Inspection and maintenance ............................................................................................... 27
F.4 Records ....................................................................................................................................... 29
Bibliography ............................................................................................................................................ 30
---------------------- Page: 5 ----------------------oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
European foreword
This document (prEN 15427-1-1:2020) has been prepared by Technical Committee CEN/TC 256
“Railway Applications”, the secretariat of which is held by DIN.This document is currently submitted to the CEN Enquiry.
This document is part of the series EN 15427, Railway applications - Wheel/Rail friction
management, which consists of the following parts:— Part 1-1: Equipment and Application – Flange Lubrication
— Part 1-2: Equipment and Application – Top of Rail materials
— Part 1-3: Equipment and Application – Adhesion materials
— Part 2-1: Properties and Characteristics – Flange lubricants
— Part 2-2: Properties and Characteristics – Top of Rail materials
— Part 2-3: Properties and Characteristics – Adhesion materials
— Part 3: Rationale for requirements and further background information
---------------------- Page: 6 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
Introduction
Friction management using solid or fluid (oil, grease, etc) substances at the wheel-rail interface is
a complex subject and includes:— lubrication of the wheel flange / rail gauge corner interface, commonly referred to as “flange
or rail lubrication”;— lubrication of the back of flange/ check rail interface, commonly referred to as “check rail
lubrication”;— altering the level of friction at the interface between the top of rail and the wheel tread,
commonly referred to as “top of rail friction management”;— applying materials to the wheel rail contact to increase (improve/ enhance/ recover) adhesion.
This document sets out requirements for the lubrication of the wheel flange / rail gauge corner and
back of flange/ check rail interface. It describes systems fitted on board trains and on the track, as
both systems may need to be employed to achieve effective lubrication of the wheel-rail interface.
Managing the wheel-rail interface effectively will reduce wear of both wheel and rail. When friction
is managed effectively, noise levels, wear levels and the risk of flange climbing are reduced.
Conversely, where not managed effectively, assets may require replacement prematurely before
reaching their full economic potential.There needs to be control in the application of lubrication such that there is:
— no loss of traction or braking performance;
— no adverse effect on signalling systems or track circuits;
— understanding of the increased risk of fire;
— no harmful environmental effect;
— no incompatibility between the different lubricants/ materials in use, particularly, between
solid and fluid systems.---------------------- Page: 7 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
1 Scope
This document is limited to specifying the requirements when applying lubricant to the interface
between the wheel flange and the rail (active interface), either directly or indirectly to the wheel
flange or to the rail and includes both trainborne and trackside solutions.This document only covers the equipment and application of lubricant to the active interface.
This document defines:— the characteristics that systems of lubrication of the wheel-rail interface shall achieve, together
with applicable inspection and test methods to be carried out for verification;— all relevant terminology which is specific to the lubrication of the wheel-rail interface.
This document only applies to the mainline railway.NOTE This document can also be used for other railways, e.g urban rail.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.prEN 15427-2-1:2020, Railway applications — Wheel/Rail friction management — Part 2-1:
Properties and Characteristics — Flange lubricants3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
active interface
contact area between wheel flange and the gauge face of the rail and contact area between the check
rail face and the back of the wheel3.2
applicator
part of trackside/trainborne equipment that delivers the lubricant to the active interface
EXAMPLE Nozzles or sticks3.3
trainborne equipment
system carried on the train that consists of one or more applicators, a storage unit and a means of
control---------------------- Page: 8 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
3.4
trackside equipment
system installed on or adjacent to the track that consists of one or more applicators, storage
containers and a means of control3.5
train operator
authority responsible for operating the train or their authorised representative
3.6
infrastructure manager
authority responsible for the infrastructure or their authorised representative
3.7
supplier
organisation responsible for supplying the equipment/ lubricant
3.8
lubricant
substance designed to alter friction at the wheel/rail active interface
3.9
technical specification
document outlining agreement between the client and the supplier
3.10
top of rail material
substance that changes the rheology of the third layer body to lower friction
4 General
4.1 Purpose of equipment
The aim of the equipment is to apply the lubricant to the active interface to reduce the risk of flange
climb derailment and achieve wheel/rail friction conditions that optimises asset life, as part of a
wider wheel/rail management strategy without compromising the safe operation of the railway.
Wheel flange/ rail friction management may be used to:— reduce noise and vibration;
— reduce the rate of wear;
— reduce number of wheel and rail defects.
The specific purpose for the use of lubrication equipment and lubricants shall be understood before
deployment in order to achieve the desired outcome (e.g reduction in wear).4.2 Application of lubricant
The trainborne/trackside lubrication equipment shall apply lubricant to take effect in the active
interface as set out in chapters 5 and 6 of this document.The trainborne/trackside lubrication equipment shall be designed to limit contamination of any
other part of the train or infrastructure.---------------------- Page: 9 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
The trainborne/ trackside lubrication system shall not compromise the performance of the train
(i.e braking and traction), see Annex B.The application of the trainborne/trackside equipment shall be considered where both can be in
use at the same location.Compatibility between different lubricants (such as flange lubricant and top of rail material/
adhesion material) in use shall be taken into account. Lubricant properties and characteristics shall
comply with the requirements set out in prEN 15427-2-1:2020.The applicator shall be adjustable such that it can be returned to its correct working position (refer
to 5.4) following wheel or rail reprofiling or other maintenance changes.A method to determine when refilling is required shall be provided.
A method by which the equipment can be checked to ensure its functional status shall be provided.
NOTE 1 Ensure the lubricant being applied to the active interface has been approved for use by the
relevant authorizing bodies (see Annex B).NOTE 2 It is good practice for all affected parties (infrastructure manger/ train operator/ suppliers) to
discuss the final use as early as possible to ensure a smooth approval process.Where there is any change to the approved design of the equipment, the customer shall be
informed. Such changes may lead to equipment requiring reapproval,5 Requirements for trainborne equipment
5.1 General
When applying to the active interface, the following shall be considered:
— method of braking (e.g. tread, disk or other);
— position and number of applicator(s) on the vehicle;
— direction of travel;
— proximity of applicator to the wheel and the rail;
— speed of train;
— frequency and amount of application.
The position and alignment of each applicator shall take into account:
— suspension movements to ensure application of the lubricant to the active interface in all
conditions;— the need to gain access for maintenance.
The trainborne equipment shall comply with the vehicle gauge.
5.2 Design of trainborne equipment
General consideration when designing and installing trainborne equipment shall include:
— ambient temperature range and climatic conditions (see EN 50125-1);---------------------- Page: 10 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
— equipment positioning – The design and location of the equipment shall factor in the
consideration for quick and easy refilling capability;— space constraints (e.g. static and dynamic);
— availability of necessary supplies (e.g. electrical, air, hydraulic, etc...);
— options for system control and lubricant regulation;
— interface with other on-board systems (e.g. braking);
— the type of lubricant to be applied and its intended function;
— total life cycle cost and maintainability;
— length/ type of train;
— interface with infrastructure systems;
— intended design life and sustainability;
— safety and reliability requirements;
— compliance with vibration and shock loads requirements of EN 61373 and EN 13749 relevant
to the position on the vehicle;— protection of the equipment from flying objects eg track ballast;
— EMC standard (EN 50121-1);
— aerodynamic effects (e.g. Wind turbulence can affect the performance of a spray system which
may be optimized by use of a windbreak);— Electronic equipment used on rolling stock (EN 62621);
— EN 50238-1:2003 Compatibility between rolling stock and train detection systems – General;
— noise emissions.5.3 Installation of trainborne equipment
The supplier of the trainborne equipment shall produce instructions for the installation and use of
the equipment.Trainborne equipment shall be installed in accordance with the manufacturer’s instructions.
The installation shall be checked after a short period of service to ensure that the lubricant is being
applied correctly to the active interface, see Annex B.5.4 Operations, Inspection and maintenance
Maintenance instructions for the trainborne equipment shall be provided. These shall include a
method for fault diagnosis to check that the trainborne equipment is not partially or fully blocked
or misaligned and that all components are securely attached to their mountings (see Annex D for
some examples).---------------------- Page: 11 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
A train maintenance plan shall include a check of the trainborne equipment to be carried out at pre-
defined intervals taking into account the equipment supplier’s instructions. This maintenance plan
shall include monitoring of lubricant usage and application alignment as a method of checking
effective delivery.Before any lubricant is used, it shall be verified if it is compatible with the equipment, as specified
in prEN 15427-2-1:2020, Annex F.5.5 Application
The equipment shall be designed so that the rate of application of the lubricant is consistent during
the agreed service conditions.Where lubricants are manually applied by the driver, consideration shall be given to record this
action.Any trainborne equipment using a spray applicator shall have a low speed cut out.
High speed cut out should be considered for trainborne equipment design.The lubricant shall be applied to area “2, 3” or “6” as shown in Figure 1.
Migration of lubricant to other zones is not desirable.
Key
1 tread
2 flange root
3 flange face
4 flange toe
5 flange tip
6 back of wheel
Figure 1 — Areas of a wheel tread
5.6 Verification
Verification of the trainborne equipment shall be undertaken to establish effective application of
the lubricant. The method chosen shall depend on the type of equipment and shall be relevant to
the application.The method of verification shall be determined between the client and supplier, see Annex B.
---------------------- Page: 12 ----------------------oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
6 Requirements for trackside equipment
6.1 General
When applying to the active interface, the following shall be considered:
— length of site to be treated;
— the number of applicators to be installed;
— direction of travel (e.g bi-directional);
— application and position at switches and crossings;
— the frequency of traffic;
— speed of traffic;
— approach to signals;
— use in terminal stations.
The position of the trackside equipment shall take into account:
— the need to gain access for maintenance;
— any hazards associated with localized contamination, e.g. if equipment placed adjacent to
platforms, pedestrian/vehicle crossings, water courses, areas where local regulations prohibit
use of equipment.The trackside equipment shall be designed, installed and maintained to limit contamination of any
other part of the train or infrastructure. Build-up of excess lubricant on the equipment, trackbed or
trains shall be avoided.6.2 Design of trackside equipment
The trackside equipment shall meet the specified requirements for application over the full range
of operating conditions. These shall include local conditions relating to:— ambient temperature range and climatic conditions;
— equipment positioning for access and space constraints;
— availability of power supplies;
— options for system adjustment, control and lubricant regulation;
— the type of lubricant;
— total life cycle cost and maintainability;
— type of trains operating on the infrastructure, including on track machines;
— speed limit;
— train frequency;
---------------------- Page: 13 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
— track form and rail profile (e.g. EN 13674-1);
— installation of the equipment.
Electrically powered equipment shall not compromise with signalling and telecommunications
integrity.Trackside equipment shall be capable of being fitted without the need for welding to rails or drilling
of rails, unless defined in the technical specification.When selecting trackside equipment, the operation of on-track machines shall be considered.
The means of adjusting the height of the applicator shall be separate from the means of attaching
to the rail. The range of adjustment shall accommodate permitted rail wear, wheel profiles, axle
loads and speeds of all train types using the route.The trackside equipment shall not infringe the infrastructure gauge.
Where the location of application changes periodically, consideration shall be given to the type of
equipment being used.Metallic armoured pipes and cables may be prohibited, the infrastructure manager shall be
consulted.6.3 Installation of trackside equipment
The installation of the trackside equipment shall take in to account the intended length of the site
to which the lubricant should be applied.The supplier of the trackside equipment shall produce instructions for the installation of the
equipment.Trackside equipment shall be installed in accordance with the manufacturer’s instructions. The
installation shall be checked after a short period of service (typically after the passage of no more
than five trains) to ensure that the lubricant is being applied correctly.NOTE Further guidance on the positioning of trackside equipment is contained in Annex D.
6.4 Operations, Inspection and maintenanceThe maintenance instruction of the trackside equipment shall be provided. These shall include an
inspection and a method for fault diagnosis to check that the equipment is not partially or fully
blocked or misaligned and all components are securely attached to their mountings.
A maintenance plan shall be produced that includes a check of the trackside equipment to be
carried out at pre-defined intervals taking into account, the equipment supplier’s instructions. This
maintenance plan should include monitoring of lubricant usage.The condition of the rail served by the equipment shall be inspected to ensure effective application
is taking place.After refilling or adjustment, the trackside equipment shall be inspected for correct application of
the lubricant from the equipment.NOTE Annex D sets out recommendations for the inspection and maintenance arrangements.
6.5 ApplicationThe equipment shall be designed so that the rate of application of the lubricant is consistent during
the agreed service conditions.The lubricant shall be applied to area “4 and 5” as shown in Figure 2, or “9” as shown in Figure 3:
---------------------- Page: 14 ----------------------oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
Key
1 field shoulder
2 crown
3 gauge shoulder
4 gauge corner
5 gauge face
6 inside of running rail (gauge face)
7 outside of running rail (field side)
8 web
Figure 2 — Areas of a rail
Key
1 check rail interface
Figure 3 — Areas of a check rail
Migration of lubricant to other zones is not desirable.
6.6 Verification
Verification of the trackside equipment shall be undertaken to establish effective application of the
lubricant. The method chosen shall depend on the type of equipment and shall be relevant to the
application.Lubricant will take time to become established on new or clean rails or wheels and can require
more than one train passage. This should be taken into consideration.NOTE Annex B sets out typical methods for verification.
---------------------- Page: 15 ----------------------
oSIST prEN 15427-1-1:2020
prEN 15427-1-1:2020 (E)
Annex A
(informative)
Types of trainborne and trackside equipment
A.1 Introduction
This annex describes flange lubrication systems currently available for trainborne and trackside
equipment.A.2 Trainborne Equipment
A.2.1 Fluid lubricant application to the active interface
The fluid lubricant is applied on to the active interface either as an air/fluid mixture or as a fluid
only. Control of the duration and/or interval of the application can be either by a timer, location,
distance counter or curve sensing or a combination.A.2.2 Solid lubricant application to the wheel
The solid lubricant is pressed against the running wheel.
A.3 Trackside Equipment
A.3.1 Mechanically activated
Mechanical trackside equipment requires physical contact or pressure from the passage of trains
to directly activate a pump, which then applies the material, through the applicator to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.