oSIST prEN 13035-1:2020

SLOVENSKI STANDARD
oSIST prEN 13035-1:2020
01-julij-2020
Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne
zahteve - 1. del: Oprema za skladiščenje, ravnanje in transport znotraj tovarne
Machines and plants for the manufacture, treatment and processing of flat glass - Safety
requirements - Part 1: Storage, handling and transportation equipment inside the factory
Maschinen und Anlagen für die Herstellung, Be- und Verarbeitung von Flachglas -
Sicherheitsanforderungen - Teil 1: Einrichtungen zum Lagern, Handhaben und
Transportieren innerhalb des Werks
Machines et installations pour la production, le façonnage et la transformation du verre
plat - Exigences de sécurité - Partie 1 : Stockage, manutention et transport à l'intérieur
de l'usine
Ta slovenski standard je istoveten z: prEN 13035-1
ICS:
81.100 Oprema za steklarsko in Equipment for the glass and
keramično industrijo ceramics industries
oSIST prEN 13035-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13035-1:2020

---------------------- Page: 2 ----------------------
oSIST prEN 13035-1:2020


DRAFT
EUROPEAN STANDARD
prEN 13035-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2020
ICS 81.100 Will supersede EN 13035-1:2008
English Version

Machines and plants for the manufacture, treatment and
processing of flat glass - Safety requirements - Part 1:
Storage, handling and transportation equipment inside the
factory
Machines et installations pour la production, le Maschinen und Anlagen für die Herstellung, Be- und
façonnage et la transformation du verre plat - Verarbeitung von Flachglas - Sicherheitsanforderungen
Exigences de sécurité - Partie 1 : Stockage, - Teil 1: Einrichtungen zum Lagern, Handhaben und
manutention et transport à l'intérieur de l'usine Transportieren innerhalb des Werks
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 151.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13035-1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 8
4 Safety requirements and/or protective measures . 12
4.1 General . 12
4.2 Mechanical strength . 12
4.3 Angle of lean . 12
4.3.1 Storage equipment and systems . 12
4.3.2 Handling equipment . 12
4.4 Cladding materials . 12
4.4.1 Cladding materials (see Figure E.2) . 12
4.4.2 Back bearers (see Figure E.2) . 12
4.4.3 Base bearers (see Figure E.2) . 13
4.5 Handling equipment . 13
4.5.1 Loading grabs . 13
4.5.2 Vacuum lifting devices . 14
4.5.3 Gripping devices (e.g. glass transport pincers (see Figure E.33)) . 15
4.5.4 Beam-strap sling . 15
4.5.5 Over-the-top grab . 15
4.6 Stationary equipment with mobile frame . 16
4.7 Other hazards . 16
5 Verification of compliance with safety requirements and/or protective measures . 16
6 Information for use . 17
6.1 General . 17
6.2 Signals and warning devices . 17
6.3 Accompanying documents . 17
6.4 Marking . 19
Annex A (normative) Requirements for stationary, movable and mobile storage equipment . 20
A.1 Mechanical strength . 20
A.2 Angle of lean . 20
A.3 Cladding materials . 20
A.3.1 Cladding materials (see Figure E.2) . 20
A.3.2 Back bearers (see Figure E.2) . 20
A.3.3 Base bearers (see Figure E.2) . 20
A.4 Stability of storage equipment . 20
A.4.1 Storage equipment . 20
A.4.2 Movable and mobile equipment . 21
A.5 Verification of compliance with safety requirements and/or protective measures . 25
2

---------------------- Page: 4 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
A.6 Information for use . 25
Annex B (informative) List of significant hazards . 26
Annex C (informative) Overview over the equipment for the storage, handling and
transportation of glass . 29
Annex D (informative) Minimum clearances for interfacing equipment . 30
D.1 Loading grab and vertical bearers . 30
D.2 Loading grab and horizontal base bearers . 30
D.3 Loading grab and horizontal back bearers . 31
D.4 Interfacing of structural (non-supporting) parts with fingers of lifting device . 33
D.5 Beam strap sling and over the top grab . 34
Annex E (informative) Terminology and figures . 35
E.1 Terms and definitions relating to the glass . 35
E.2 Terms and definitions relating to the storage equipment . 36
E.2.1 Orientation (positioning) of glass in any type of equipment . 36
E.2.2 Type of storage equipment . 38
E.2.2.1 Stationary equipment . 38
E.2.2.2 Stationary equipment with mobile supporting frame . 40
E.2.2.3 Movable equipment . 42
E.2.2.4 Mobile storage equipment . 47
E.2.3 Type of handling equipment . 49
E.2.3.1 Manual devices . 49
E.2.3.2 Mechanical devices . 50
E.2.3.3 Vacuum devices . 58
E.2.4 Type of transportation equipment . 60
E.2.4.1 Equipment by lifting prior to transportation . 60
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 64
Bibliography . 74

3

---------------------- Page: 5 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
European foreword
This document (prEN 13035-1:2020) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by
DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13035-1:2008.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
The main changes compared to the previous edition are as follows:
— Clarification of machine according to Directive 2006/42/EC or not;
— Controls, PL;
— Vacuum lifting devices have been added to the scope (also devices not used for crane operation).

4

---------------------- Page: 6 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
Introduction
This document is a type-C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
a) machine manufacturers (small, medium and large enterprises);
b) health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
a) machine users/employers (small, medium and large enterprises);
b) machine users/employees (e.g. trade unions, organizations for people with special needs);
c) service providers, e.g. for maintenance (small, medium and large enterprises);
d) consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events
are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
In this document it is assumed that:
— negotiation occurs between the manufacturer and the user/purchaser concerning particular
conditions of use not dealt with in this standard and specific interfaces consideration (e.g. Annex D -
Minimum clearances for interfacing equipment);
— the floors inside the factory, which are used for glass storage and withdrawal processes, are virtually
horizontal and free of significant irregularities.
5

---------------------- Page: 7 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
1 Scope
1.1 This document includes safety requirements for the design and installation of equipment that is
intended for storage, handling and transportation of flat glass inside the factory. It also applies to
equipment within the scope of EU Directives as well as to equipment that is covered by non-harmonized
documents. Annex E gives an overview of the differentiation.
1.2 This document specifies safety requirements for the following equipment:
— equipment for storage provided with elements that are propelled by a drive system other than
directly applied human or animal power (engine power) in order to store or retrieve glass in or from
storage shelves or frames (see 3.2.2);
— equipment for picking up single glass plates, firmly-attached glass plates or glass packs for
transportation between different locations where the retention force or lifting force is generated by
engine power (see 3.3.2, 3.3.3);
— equipment for transportation by special vehicles that are propelled by engine power.
1.3 This document specifies additional requirements for the following equipment that is not covered
by EU Directives:
— stationary, movable and mobile storage equipment (see 3.2.1, 3.2.3, 3.2.4, for requirements see
Annex A);
— storage equipment that is provided with manually propelled shelves or frames (see 3.2.2, for
requirements see Annex B);
— equipment for transportation by special vehicles that are not self-propelled (see 3.4.3, for
requirements see Annex C).
NOTE Additional requirements covering specific hazards that are resulting from the use outside the factory
are dealt with in EN 13035-2.
1.4 This document only deals with equipment which is in direct contact with the glass, with the
exception of wooden packaging. Tractors, cranes, hoists and forklift trucks as well as elements of self-
propelled vehicles, which are not in contact with the glass (see 3.4.1), are out of the scope. This document
does not apply to equipment for picking up single plates, such as manual vacuum lifting devices, lifting
straps or other manual devices. This document does not cover automatic loading or unloading of storage
and transportation equipment. This is covered in EN 13035-5.
1.5 This document deals with all significant hazards, hazardous situations and hazardous events, which
are relevant to equipment for storage, handling and transportation of flat glass, when they are used as
intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see
Annex D). This document specifies the appropriate technical measures to eliminate or reduce risks
arising from the significant hazards during commissioning, operation and maintenance. Noise hazards
have not been considered significant for any type of equipment within the scope of this document.
1.6 This document is not applicable to equipment for storage, handling and transportation of flat glass
inside the factory, which is manufactured before the date of publication of this document by CEN.
6

---------------------- Page: 8 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1757-3:2002, Safety of industrial trucks — Pedestrian controlled manual and semi-manual trucks —
Part 3: Platform trucks
1)
EN 1993-1-1:2005, Eurocode 3: Design of steel structures — Part 1-1: General rules and rules for
buildings
EN 13035-5:2006+A1:2009, Machines and plants for the manufacture, treatment and processing of flat
glass — Safety requirements — Part 5: Machines and installations for stacking and de-stacking
EN 13155:2020, Crane — Safety — Non-fixed load lifting attachments
EN 13557:2003+A2:2008, Cranes — Controls and control stations
EN 60204-1:2018, Safety of machinery — Electrical equipment of machines — Part 1: General
requirements (IEC 60204-1:2016, modified)
EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their
components (ISO 4414:2010)
EN ISO 11201:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission
sound pressure levels at a workstation and at other specified positions in an essentially free field over a
reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 11202:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission
sound pressure levels at a workstation and at other specified positions applying approximate environmental
corrections (ISO 11202:2010)
EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)
EN ISO 13849-1:2015, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design (ISO 13849-1:2015)
EN ISO 13850:2015, Safety of machinery — Emergency stop function — Principles for design
(ISO 13850:2015)
EN ISO 13854:2019, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
(ISO 13854:2017)
EN ISO 13855:2010, Safety of machinery — Positioning of safeguards with respect to the approach speeds
of parts of the human body (ISO 13855:2010)
EN ISO 13857:2019, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2019)

1)
As impacted by EN 1993-1-1:2005/A1:2014.
7

---------------------- Page: 9 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
EN ISO 14118:2018, Safety of machinery — Prevention of unexpected start-up (ISO 14118:2017)
EN ISO 14119:2013, Safety of machinery — Interlocking devices associated with guards — Principles for
design and selection (ISO 14119:2013)
EN ISO 14120:2015, Safety of machinery — Guards — General requirements for the design and
construction of fixed and movable guards (ISO 14120:2015)
EN ISO 14122-1:2016, Safety of machinery — Permanent means of access to machinery — Part 1: Choice
of fixed means and general requirements of access (ISO 14122-1:2016)
ISO 3864-1:2011, Graphical symbols — Safety colours and safety signs — Part 1: Design principles for
safety signs and safety markings
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
General terms and definitions

3.1.1
inside the factory
all areas inside of enclosed buildings and company premises for the manufacture, treatment and
processing of glass, where the glass is stored and transported, including storage facilities, with the
exception of building sites
3.1.2
floor structure
structure including the technical definition of the floor regarding:
— surface tolerance;
— inclination of the floor;
— strength, i.e. load capacity and flexural resistance
3.1.3
angle of lean
difference between the plane of the glass plate and the vertical axis (e.g. Figure E.2)
3.1.4
glass pack
assembly of two or more glass plates of usually the same size (e.g. Figures E.1 and E.16)
8

---------------------- Page: 10 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
3.1.5
bearer
structural member of a stillage that supports the load of the glass; there are two main types:
3.1.5.1
back bearer
fixed vertical construction against which the glass plate or glass pack is leant (e.g. Figure E.2)
3.1.5.2
base bearer
fixed horizontal construction on which the glass plate or glass pack stands (e.g. Figure E.2)
3.1.6
cladding
material used to prevent the glass plate or glass pack being damaged by the bearers (e.g. Figure E.2)
3.1.7
retention device
facility to secure the glass on movable or mobile stillages against falling over
3.1.8
clamp (top or side)
movable means on load lifting attachments, such as side-loading grabs, which retains the glass pack near
the outer edges (e.g. Figure E.25)
3.1.9
supporting foot (shoe for beam-strap sling)
device carrying the weight of the glass pack; it can be fixed, adjustable or removable depending on the
type of device used (e.g. Figures E.25, E.31 and E.45)
3.2
storage equipment
integral, movable or mobile equipment for storing glass packs, firmly-attached glass plates or single
plates. Certain equipment is also used for transportation
The different types are:
3.2.1
stationary equipment
racks, either fixed to the floor or stably freestanding, intended for single glass plates or glass packs; this
type of stillage shall not be moved in loaded condition (e.g. Figures E.1 to E.7)
3.2.2
stationary equipment with mobile frame
equipment designed to save space without loss of accessibility. The main types are:
3.2.2.1
drawer-type storage
equipment where all movable frames are placed directly side by side without any gaps in between; each
frame is pulled out longitudinally, either by hand or by engine power, to load or unload the glass (e.g.
Figure E.8)
9

---------------------- Page: 11 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
3.2.2.2
compact-type storage
equipment where all movable frames are placed directly side by side without any gaps in between; the
frames are moved transversely, either by hand or by engine power, to load or unload the glass (e.g.
Figures E.9 a) and E.9 b)
3.2.2.3
shuttle system
equipment for transportation of storage equipment carrying one or more single glass plates from line
transport into a parallel transport route by lateral movement (Figure E.10)
3.2.3
movable equipment
stable equipment that is usually used for temporary storage and for transportation, intended to be moved
when loaded with glass
The different types are:
3.2.3.1
pallet
device used both inside the factory and for transportation to the customer, characterised by its ability to
be stacked vertically, one upon the other, to form a stable free-standing unit, within the factory usually
transported by a mechanical device that lifts it off the ground prior to transportation (e.g. Figures E.11 to
E.13)
3.2.3.2
movable stillage
device normally used for storage and transportation of glass to the customer, within the factory, usually
transported by a mechanical device that lifts it off the ground prior to movement. Typically, it cannot be
stacked like a pallet without using special ancillary equipment (e.g. Figures E.14 and E.15)
3.2.3.3
thin-glass frame
device for storage and transportation of glass packs having a sheet thickness of less than 2,5 mm (e.g.
Figure E.24)
3.2.3.4
collier
metallic packaging used for storage and for transportation of the glass to the customer, which is
positioned vertically inside the colliers intended to be opened only in an inclined position, e.g. on a stillage
(e.g. Figure E.45)
3.2.4
mobile equipment
device usually used for temporary storage and for transportation normally only inside the factory, similar
to movable stillages, but characterised by having integral wheels and the ability to be propelled either
manually or powered (e.g. Figures E.17 to E.21)
3.3
handling equipment (load lifting attachment)
specifically, designed device to support and retain a single glass plate, firmly-attached glass plates or a
glass pack during transportation between different locations
10

---------------------- Page: 12 ----------------------
oSIST prEN 13035-1:2020
prEN 13035-1:2020 (E)
3.3.1
manual load lifting attachment
directly hand-held device for holding and directing the glass plate during transportation between
different locations, such as hand carrying straps, manual vacuum lifting devices, etc. (e.g. Figures E.22
and E.23)
3.3.2
mechanical equipment
device to retain and support the glass during transportation between different locations either manually
or powered, the equipment can include special devices that are required for handling single plates or (a)
pack(s) of thin glass and can also be part of the storage equipment
Note 1 to entry: Different types of (transportation) devices used are shown in Figures E.24 to E.32.
3.3.2.1
loading grab
mechanical device intended for transportation of gl
...