SIST EN IEC 60335-2-75:2023

SLOVENSKI STANDARD
SIST EN IEC 60335-2-75:2023
01-julij-2023
Gospodinjski in podobni električni aparati - Varnost - 2-75. del: Posebne zahteve
za komercialne dozirne in prodajne avtomate (IEC 60335-2-75:2012)
Household and similar electrical appliances - Safety - Part 2-75: Particular requirements
for commercial dispensing appliances and vending machines (IEC 60335-2-75:2012)
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-75:
Besondere Anforderungen für Ausgabegeräte und Warenautomaten für den
gewerblichen Gebrauch (IEC 60335-2-75:2012)
Appareils électrodomestiques et analogues - Sécurité - Partie 2-75: Exigences
particulières pour les distributeurs commerciaux avec ou sans moyen de paiement (IEC
60335-2-75:2012)
Ta slovenski standard je istoveten z: EN IEC 60335-2-75:2023
ICS:
55.230 Razdelilni in prodajni Distribution and vending
avtomati machines
SIST EN IEC 60335-2-75:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60335-2-75:2023

---------------------- Page: 2 ----------------------
SIST EN IEC 60335-2-75:2023


EUROPEAN STANDARD
EN IEC 60335-2-75

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2023
ICS 55.230 Supersedes EN 60335-2-75:2004; EN 60335-2-
75:2004/A1:2005; EN 60335-2-75:2004/A11:2006; EN
60335-2-75:2004/A2:2008; EN 60335-2-
75:2004/A12:2010
English Version
Household and similar electrical appliances - Safety - Part 2-75:
Particular requirements for commercial dispensing appliances
and vending machines
(IEC 60335-2-75:2012)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-75: Exigences particulières pour les distributeurs ähnliche Zwecke - Teil 2-75: Besondere Anforderungen für
commerciaux avec ou sans moyen de paiement Ausgabegeräte und Warenautomaten für den gewerblichen
(IEC 60335-2-75:2012) Gebrauch
(IEC 60335-2-75:2012)
This European Standard was approved by CENELEC on 2020-11-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60335-2-75:2023 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60335-2-75:2023
EN IEC 60335-2-75:2023 (E)
European foreword
This document (EN IEC 60335-2-75:2023) consists of the text of document IEC 60335-2-75:2012 edition
3.0 prepared by IEC/TC 61 "Safety of household and similar electrical appliances".
The following dates are fixed:
• latest date by which this document has to be (dop) 2023-11-05
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) 2026-05-05
conflicting with this document have to be withdrawn
This document supersedes EN 60335-2-75:2004+A1:2005+A11:2006+A2:2008+A12:2010 when
EN IEC 60335-2-75/A11:2023 is published.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 60335-2-75:2023/A1:2023,
EN IEC 60335-2-75:2023/A2:2023 and EN IEC 60335-2-75:2023/A11:2023.
This document has been prepared under a Standardization Request given to CENELEC by the European
Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60335-2-75:2012 was approved by CENELEC as a European
Standard without any modification.









2

---------------------- Page: 4 ----------------------
SIST EN IEC 60335-2-75:2023



IEC 60335-2-75

®


Edition 3.0 2012-12




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Household and similar electrical appliances – Safety –

Part 2-75: Particular requirements for commercial dispensing appliances and

vending machines




Appareils électrodomestiques et analogues – Sécurité –

Partie 2-75: Exigences particulières pour les distributeurs commerciaux avec ou


sans moyen de paiement













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX V


ICS 55.230 ISBN 978-2-83220-513-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------
SIST EN IEC 60335-2-75:2023
– 2 – 60335-2-75 © IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 8
3 Terms and definitions . 8
4 General requirement . 10
5 General conditions for the tests . 10
6 Classification . 11
7 Marking and instructions . 12
8 Protection against access to live parts . 14
9 Starting of motor-operated appliances . 14
10 Power input and current. 14
11 Heating. 14
12 Void . 15
13 Leakage current and electric strength at operating temperature . 15
14 Transient overvoltages . 16
15 Moisture resistance . 16
16 Leakage current and electric strength . 19
17 Overload protection of transformers and associated circuits . 19
18 Endurance . 19
19 Abnormal operation . 19
20 Stability and mechanical hazards. 21
21 Mechanical strength . 21
22 Construction . 21
23 Internal wiring . 24
24 Components . 25
25 Supply connection and external flexible cords . 26
26 Terminals for external conductors . 26
27 Provision for earthing . 26
28 Screws and connections . 26
29 Clearances, creepage distances and solid insulation . 27
30 Resistance to heat and fire . 27
31 Resistance to rusting . 27
32 Radiation, toxicity and similar hazards . 27
Annexes . 29
Annex AA (normative) Aging test for elastomeric parts . 29
Bibliography . 31

Figure 101 – Splash apparatus . 28

---------------------- Page: 6 ----------------------
SIST EN IEC 60335-2-75:2023
60335-2-75 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-75: Particular requirements for commercial
dispensing appliances and vending machines


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This part of International Standard IEC 60335 has been prepared by IEC technical committee 61:
Safety of household and similar electrical appliances.
This third edition cancels and replaces the second edition published in 2002 including its
Amendment 1 (2004) and its Amendment 2 (2008). It constitutes a technical revision.
The principal changes in this edition as compared with the second edition of IEC 60335-2-75
are as follows (minor changes are not listed):
• some notes have been deleted or converted to normative text (5.2, 5.6, 5.104, 7.12.1,
7.12.101.1, 11.2, 11.8, 15.2.103, 15.2.104, 15.2.106, 15.2.109, 15.2.111, 19.102, 19.6, 19.13,
19.101, 22.6, 22.7, 22.112, 22.113, 22.114, 24.102, 27.2).
• added requirements for espresso coffee makers in 3.115, 22.114 and throughout standard;

---------------------- Page: 7 ----------------------
SIST EN IEC 60335-2-75:2023
– 4 – 60335-2-75 © IEC:2012
• modified 11.4 to address heating appliances with electronic process controls and 11.6 to
address combined appliances without electronic process controls;
• modified Clause 22 to indicate that pressure regulating devices are to be rendered
inoperable;
• deleted ISO 13732-1 from Bibliography.
The text of this standard is based on the following documents:
FDIS Report on voting
61/4458/FDIS 61/4512/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the fifth edition (2010) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Safety requirements for commercial dispensing
appliances and vending machines.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.

---------------------- Page: 8 ----------------------
SIST EN IEC 60335-2-75:2023
60335-2-75 © IEC:2012 – 5 –
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.
A list of all parts of the IEC 60335 series, under the general title: Household and similar
electrical appliances – Safety, can be found on the IEC website.
The following differences exist in the countries indicated below.
– 6.1: Class 0I is allowed for appliances used indoors having a rated voltage not exceeding
150 V (Japan).
– 13.2: The leakage current limits are different (Japan).
– 16.2: The leakage current limits are different (Japan).

---------------------- Page: 9 ----------------------
SIST EN IEC 60335-2-75:2023
– 6 – 60335-2-75 © IEC:2012
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions. It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of
the requirements and, if found to be substantially equivalent, may be considered to comply
with the standard.

---------------------- Page: 10 ----------------------
SIST EN IEC 60335-2-75:2023
60335-2-75 © IEC:2012 – 7 –
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-75: Particular requirements for commercial
dispensing appliances and vending machines



1 Scope
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of electric commercial dispensing
appliances and vending machines for preparation or delivery of food, drinks and consumer
products, their rated voltage being not more than 250 V for single-phase appliances and
480 V for other appliances.
NOTE 101 Examples of appliances that are within the scope of this standard are
– bulk tea or coffee brewing machines;
– cigarette vending machines;
– coffee grinders;
– commercial liquid heaters;
– coffee makers with or without integrated coffee grinder;
– coffee makers with cooling systems;
– hot and cold beverage vending machines;
– hot water dispensers;
– ice cream and whipped cream dispensers;
– ice dispensers;
– newspaper, audio or video tape or disc vending machines;
– packaged food and drink vending machines;
– refrigerated merchandisers.
Appliances can have more than one function.
NOTE 102 Other standards may be applicable for some functions such as
– refrigeration (IEC 60335-2-24);
– heating by microwaves (IEC 60335-2-25).
This standard also deals with the hygiene aspects of appliances.
As far as is practicable, this standard deals with the common hazards presented by
appliances that are encountered by users and maintenance persons. However, in general, it
does not take into account young children playing with the appliance.
NOTE 103 Attention is drawn to the fact that
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be
necessary;
– in many countries, additional requirements for appliances incorporating pressure vessels are specified;
– in many countries, additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
NOTE 104 This standard does not apply to
– appliances intended to be used exclusively for household purposes;
– appliances intended to be used exclusively for industrial purposes;

---------------------- Page: 11 ----------------------
SIST EN IEC 60335-2-75:2023
– 8 – 60335-2-75 © IEC:2012
– appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas);
– commercial electric boiling pans (IEC 60335-2-47);
– commercial electric bains-marie (IEC 60335-2-50);
– amusement machines and personal service machines (IEC 60335-2-82);
– appliances solely used for dispensing money;
– display cabinets;
– appliances incorporating electrode-type water heaters.
2 Normative references
This clause of Part 1 is applicable except as follows.
Addition:
IEC 60335-2-34, Household and similar electrical appliances – Safety – Part 2-34: Particular
requirements for motor-compressors
ISO 1817:2011, Rubber, vulcanized or thermoplastic – Determination of the effect of liquids
3 Terms and definitions
This clause of Part 1 is applicable except as follows.
3.1.9 Replacement:
normal operation
operation of the appliance under the following conditions:
The appliance is operated in the standby mode until steady conditions are established and
then under the most unfavourable dispensing procedure. The appliance is refilled when
necessary in accordance with the instructions for use, or the instructions for maintenance,
and the next operating period started as soon as possible.
Lids and covers of appliances of the professional type and of appliances of the
supervised type are placed in their intended positions.
Coffee makers are operated with their container filled with the rated capacity of water, or
connected to the water mains, if applicable. Coffee makers with a heated surface intended to
keep the liquid warm are operated with or without the container, whichever is the more
unfavourable.
3.6.2 Replacement:
detachable part
part that can be removed without the aid of a tool, a part that is removed in accordance with
the instructions for use or the instructions for maintenance, even if a tool or access key is
needed for removal, or a part that does not fulfill the test of 22.11
Note 1 to entry: If a part has to be removed for installation purposes, this part is not considered to be detachable
even if the instructions state that it is to be removed.
Note 2 to entry: A part that can be opened is considered to be a part that can be removed.
3.7.3 Replacement:
thermal cut-out
device that during abnormal operation limits the temperature of the controlled part by
automatically opening the circuit, or reducing the current, and is constructed so that its setting
cannot be altered by the user or the maintenance person

---------------------- Page: 12 ----------------------
SIST EN IEC 60335-2-75:2023
60335-2-75 © IEC:2012 – 9 –
3.8.5 Replacement:
maintenance operation
operation performed in the maintenance area or user area, such as preparing the appliance
for new products or new operating methods, cleaning, price changing, replenishing, coin
collecting and setting of controls or similar operations
Note 1 to entry: Maintenance operation does not include operations performed in the service area.
3.101
rated pressure
pressure assigned to the pressurized parts of the appliance by the manufacturer
3.102
standby mode
state of the appliance when filled as intended with ingredients or products, energized and
ready for use, cash boxes and overflow containers being empty
3.103
access key
key or other means that gives access to the maintenance area but does not give access to
the service area
Note 1 to entry: "Other means" includes a tool or operation by codes or signals produced by optical or electro-
magnetic sources.
3.104
override key
key or other means that is used to render an interlock inoperative
3.105
dispensing appliance
appliance intended to deliver or make available food, drinks or other consumer products
Note 1 to entry: The appliance may also prepare the products.
Note 2 to entry: The dispensing operation may be initiated manually or by means such as coins or credit cards.
3.106
vending machine
dispensing appliance that is operated by coins, credit cards or other means of payment
3.107
instructions for maintenance
instructions explaining how to carry out cleaning, replenishing, coin collecting, setting of
controls and similar operations
3.108
maintenance person
person who maintains the appliance in accordance with the instructions for maintenance
3.109
user area
area where access is gained without the use of an access key or a tool
Note 1 to entry: The user area of appliances of the supervised type is determined with detachable parts and
other movable parts, such as doors and lids, in position as in normal use.
Note 2 to entry: Appliances of the professional type have no user area.

---------------------- Page: 13 ----------------------
SIST EN IEC 60335-2-75:2023
– 10 – 60335-2-75 © IEC:2012
3.110
maintenance area
area where access can only be gained by the use of an access key
3.111
service area
area where access cannot be gained by the use of an access key alone
3.112
appliance of the professional type
dispensing appliance that is only intended to be used by trained personnel such as kitchen
or bar staff
3.113
appliance of the supervised type
dispensing appliance that is intended to be maintained by trained personnel but may be
used by other persons in a location where its use is overseen
Note 1 to entry: Dining rooms in restaurants
...