SIST EN 1529:2022
(Main)Door leaves - Height, width, thickness and squareness - Tolerance classes
Door leaves - Height, width, thickness and squareness - Tolerance classes
This document gives the tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies to door leaves which are supplied without, and independent of, any frames. It does not apply to the leaves of doorsets.
NOTE Compliance with the tolerance limits given in this document does not imply that this would necessarily produce a perfect fit between door leaves and frames
Türblätter - Höhe, Breite, Dicke und Rechtwinkligkeit - Toleranzklassen
Dieses Dokument legt die Toleranzgrenzen zu den vereinbarten Abmessungen von Höhe, Breite und Dicke sowie zur Rechtwinkligkeit von Türblättern fest. Es gilt für Türblätter, die ohne bzw. unabhängig von den Zargen geliefert werden. Es gilt nicht für Türblätter von Türelementen.
ANMERKUNG Selbst wenn die Toleranzgrenzen dieses Dokuments eingehalten werden, bedeutet dies nicht, dass daraus zwangsläufig eine einwandfreie Passung zwischen Türblättern und Zargen resultiert.
Vantaux de portes - Hauteur, largeur, épaisseur et équerrage - Classes de tolérances
Le présent document donne les limites de tolérances des valeurs spécifiées de hauteur, largeur et épaisseur des vantaux de portes ainsi que de leur équerrage. Il s'applique aux vantaux livrés sans huisseries et indépendamment de ces dernières. Il ne s'applique pas aux vantaux des blocs portes.
NOTE La conformité aux limites de tolérances données dans le présent document n'implique pas nécessairement un ajustement parfait entre vantaux et huisseries.
Vratna krila - Višina, širina, debelina in pravokotnost - Tolerančni razredi
V tem dokumentu so podane mejne tolerance za določene višine, širine in debeline ter pravokotnost vratnih kril. Uporablja se za vratna krila, ki so dobavljena brez okvirjev in neodvisno od njih. Ne uporablja se za krila sestavljenih vrat.
OPOMBA: Skladnost z mejnimi tolerancami, podanimi v tem dokumentu, ne pomeni, da to zagotavlja popolno prileganje vratnih kril in okvirjev.
General Information
Relations
Overview
SIST EN 1529:2022 is a European standard established by CEN that defines tolerance classes for door leaves-specifically their height, width, thickness, and squareness. This standard applies exclusively to standalone door leaves supplied without any frames and excludes door leaves that are part of complete doorsets. The standard presents clear tolerance limits to ensure consistent manufacturing quality while acknowledging that compliance does not guarantee a perfect fit between door leaves and doorframes.
The standard supersedes EN 1529:1999 and introduces updates such as the removal of tolerance class 0 and various editorial improvements. It aligns with measurement methodologies found in EN 951 and supports manufacturers and quality inspectors in verifying dimensional accuracy for door leaves.
Key Topics
Tolerance Classes: SIST EN 1529:2022 specifies three tolerance categories based on permitted deviations in door leaf dimensions and squareness.
- Class 1: ±2.0 mm (height/width), ±1.5 mm (thickness), 1.5 mm (squareness)
- Class 2: ±1.5 mm (height/width), ±1.0 mm (thickness), 1.5 mm (squareness)
- Class 3: ±1.0 mm (height/width), ±0.5 mm (thickness), 1.0 mm (squareness)
Dimensional Scope: The standard focuses on four primary dimensions for door leaves:
- Height
- Width
- Thickness
- Squareness (right-angle precision)
Measurement Methodology: The tolerances are to be assessed following the measurement procedures defined in EN 951, ensuring consistency and accuracy in evaluation.
Limitations: This standard does not guarantee that compliant door leaves will perfectly fit door frames, as fitment also depends on frames and installation specifics. Also, any modifications such as rebating or finishing after production can affect dimensions and invalidate conformity.
Applications
SIST EN 1529:2022 is essential for:
- Manufacturers of Door Leaves: To maintain production quality control and ensure door leaves comply with defined dimensional tolerances.
- Quality Control and Inspection: For assessing door leaf dimensions during quality assurance processes.
- Architects and Builders: To specify and confirm acceptable tolerance limits for door leaves in construction projects.
- Regulatory Compliance: Ensures alignment with European standards for construction materials, facilitating market access across member countries.
This standard supports industries that require standardized door components, including residential, commercial, and industrial construction sectors seeking durable, dimensionally consistent door leaves.
Related Standards
EN 951 – Door Leaves: Method for Measurement of Height, Width, Thickness, and Squareness
EN 1529 relies on EN 951 for its detailed measurement methodology to ensure uniform testing procedures.EN 14351-1 – Windows and Doors: Product Standard, Performance Characteristics
Provides broader performance and safety requirements for door and window products.EN 16034 – Fire Resistant Doorsets and Elements of Building Hardware
Complementary standard for door leaves requiring fire resistance properties.ISO and IEC Terminology Databases
Provides official terminology related to door manufacturing and dimensions, supporting standardization efforts.
By adhering to SIST EN 1529:2022, stakeholders can ensure consistent quality and dimensional accuracy of door leaves across European markets, facilitating interoperability, safety, and customer satisfaction in door manufacturing and installation industries.
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2022
Nadomešča:
SIST EN 1529:2000
Vratna krila - Višina, širina, debelina in pravokotnost - Tolerančni razredi
Door leaves - Height, width, thickness and squareness - Tolerance classes
Türblätter - Höhe, Breite, Dicke und Rechtwinkligkeit - Toleranzklassen
Vantaux de portes - Hauteur, largeur, épaisseur et équerrage - Classes de tolérances
Ta slovenski standard je istoveten z: EN 1529:2021
ICS:
91.060.50 Vrata in okna Doors and windows
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 1529
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 91.060.50 Supersedes EN 1529:1999
English Version
Door leaves - Height, width, thickness and squareness -
Tolerance classes
Vantaux de portes - Hauteur, largeur, épaisseur et Türblätter - Höhe, Breite, Dicke und Rechtwinkligkeit -
équerrage - Classes de tolérances Toleranzklassen
This European Standard was approved by CEN on 22 September 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1529:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Classification . 4
European for
...
Frequently Asked Questions
SIST EN 1529:2022 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Door leaves - Height, width, thickness and squareness - Tolerance classes". This standard covers: This document gives the tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies to door leaves which are supplied without, and independent of, any frames. It does not apply to the leaves of doorsets. NOTE Compliance with the tolerance limits given in this document does not imply that this would necessarily produce a perfect fit between door leaves and frames
This document gives the tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies to door leaves which are supplied without, and independent of, any frames. It does not apply to the leaves of doorsets. NOTE Compliance with the tolerance limits given in this document does not imply that this would necessarily produce a perfect fit between door leaves and frames
SIST EN 1529:2022 is classified under the following ICS (International Classification for Standards) categories: 91.060.50 - Doors and windows. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 1529:2022 has the following relationships with other standards: It is inter standard links to SIST EN 1529:2000. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 1529:2022 is associated with the following European legislation: EU Directives/Regulations: 305/2011. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 1529:2022 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
記事要約: SIST EN 1529:2022 - ドアの横木 - 高さ、幅、厚さ、正方形 - 許容クラス 記事内容: この文書は、ドアの横木の高さ、幅、厚さ、および正方形の許容範囲を示しています。これはフレームなしで供給されるドアの横木に適用されます。ただし、ドアセットの葉には適用されません。 注意: この文書で示された許容範囲を満たすことが、ドアの横木とフレームの間で必ずしも完全な適合性を生じることを意味するものではありません。
기사 요약: SIST EN 1529:2022 - 도어 리브 - 높이, 너비, 두께 및 정사각형 - 허용 오차 등급 기사 내용: 이 문서는 도어 리브의 높이, 너비, 두께 및 정사각형에 대한 허용 오차 한계를 제공합니다. 이는 프레임 없이 공급되는 도어 리브에 적용됩니다. 이는 도어세트의 문 잎에는 적용되지 않습니다. 참고: 이 문서에서 제공된 허용 오차 한계를 준수한다고 해서 도어 리브와 프레임 사이에 완벽한 적합성이 항상 생기는 것은 아닙니다.
The article discusses the tolerances for the height, width, thickness, and squareness of door leaves. These tolerances apply to door leaves that are sold separately from frames and not to doorsets as a whole. It is important to note that meeting these tolerance limits does not guarantee a perfect fit between door leaves and frames.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...