iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 17821:2023/AC:2024

(Corrigendum)

Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification

Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification

This document specifies:
- general construction, performance and material requirements for Frost Resistant Taps for outdoor use (FRT), PN 10.
- the application in the potable water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
FRT valves shall consist of the 3 areas shown in Figure 1.
The conditions of use are according to the following Table 1.
The requirements with regard to the potable water quality are specified in national regulations.

Gebäudearmaturen - Frostbeständige Armaturen für den Außenbereich (FRT) - Allgemeine technische Spezifikation

Dieses Dokument legt Folgendes fest:
   allgemeine Konstruktions-, Betriebs- und Materialanforderungen für frostbeständige Armaturen für den Außenbereich (FRT, en: Frost Resistant Taps for outdoor use), PN 10.
   Die Anwendung in der Trinkwasser-Installation mit einem statischen Druck von maximal 1,0 MPa (10 bar) und einer Trinkwassertemperatur von maximal 25 °C (PWC).
FRT-Ventile müssen aus den 3 Bereichen bestehen, die in Bild 1 dargestellt sind.
Die Einsatzbedingungen sind in der folgenden Tabelle 1 aufgeführt.
[Bild 1]
[Tabelle 1]
[…]

Robinetterie de bâtiment - Robinets résistant au gel pour une utilisation en extérieur (FRT) - Spécifications techniques générales

Le présent document spécifie :
 les exigences générales relatives à la conception, à la performance et aux matériaux pour les robinets
résistant au gel pour une utilisation en extérieur (FRT), PN 10.
 l’application dans l’installation d’eau potable avec une pression statique de 1,0 MPa (10 bar)
maximum et une température de distribution de 25 °C (EPF) maximum.
Les robinets FRT doivent comprendre les trois zones indiquées à la Figure 1.
Les conditions d’utilisation sont conformes au Tableau 1 suivant.
[Figure 1]
[Tableau 1]
Les exigences applicables à la qualité de l’eau potable sont spécifiées dans les réglementations nationales.

Ventili v stavbah - Proti zmrzali odporne pipe za zunanjo uporabo (FRT) - Splošna tehnična specifikacija - Popravek AC

General Information

Status
Published
Publication Date
23-May-2024
ICS
23.060.01 - Valves in general
91.140.60 - Water supply systems
Technical Committee
IOVO - Water supply and waste water engineering
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
23-May-2024
Due Date
28-Jul-2024
Completion Date
24-May-2024
Ref Project
EN 17821:2023/AC:2024 - Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification

Relations

Corrects
SIST EN 17821:2023 - Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
Effective Date
13-Mar-2024

Buy Standard

EN 17821:2023/AC:2024EN 17821:2023/AC:2024
PreviousNext
Corrigendum
EN 17821:2023/AC:2024
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17821:2023/AC:2024
01-julij-2024
Ventili v stavbah - Proti zmrzali odporne pipe za zunanjo uporabo (FRT) - Splošna
tehnična specifikacija - Popravek AC
Building valves - Frost resistant taps for outdoor use (FRT) - General technical
specification
Gebäudearmaturen - Frostbeständige Armaturen für den Außenbereich (FRT) -
Allgemeine technische Spezifikation
Robinetterie de bâtiment - Robinets résistant au gel pour une utilisation en extérieur
(FRT) - Spécifications techniques générales
Ta slovenski standard je istoveten z: EN 17821:2023/AC:2024
ICS:
23.060.01 Ventili na splošno Valves in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN 17821:2023/AC:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17821:2023/AC:2024

---------------------- Page: 2 ----------------------
SIST EN 17821:2023/AC:2024


EUROPEAN STANDARD EN 17821:2023/AC

NORME EUROPÉENNE
May 2024


EUROPÄISCHE NORM
ICS 23.060.01; 91.140.60
English version

Building valves - Frost resistant taps for outdoor use (FRT) - General technical
specification
Robinetterie de bâtiment - Robinets résista
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 17821:2023(Main)
Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
EN 17821:2023

This document specifies general construction, performance and material requirements for the tapware FRT, PN 10. The application in the drinking water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
The conditions of use are according to the following Table 1:
[Table 1 - Conditions of use]
[Figure 1 - The different areas of FRT]

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1491:2022(Main)
Building valves - Expansion valves - Tests and requirements
EN 1491:2022

This document specifies dimensions, materials and performance requirements (including methods of test) for expansion valves, of nominal sizes from DN 15 to DN 32, having working pressures ) from 0,1 MPa (l bar) to 1,0 MPa (10 bar).
Expansion valves are intended for fitting to the cold potable water supply of storage water heaters, having a maximum distribution temperature of 95 °C, for all energy sources.
Expansion valves do not control the temperature and alone do not constitute the protection required for storage water heaters. Expansion valves limit pressure, in the water heaters to what they are fitted, that is produced by thermal expansion of the water.
NOTE   The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1488:2021(Main)
Building valves - Expansion groups - Tests and requirements
EN 1488:2021

The document specifies, dimensions, materials and performance requirements (including methods of test) for expansion groups, of nominal sizes from DN 15 to DN 25, having working pressures ) from 0,1 MPa (1 bar) to 1,0 MPa (10 bar).
Expansion groups shall be fitted to the cold potable water supply only for expansion purposes, e.g. of storage water heaters, having a maximum distribution temperature of 95 °C.
Expansion groups limit pressure in the water heater to which they are fitted, that is produced by thermal expansion of the water, prevent the backflow of water into the supply pipe and prevent the discharged water to get into contact with the water in the water heater.
Expansion groups do not control temperature and alone do not constitute the protection required for storage water heaters.
NOTE   The use of the device specified in this Standard does not override the need to use controls (e.g. thermostats and thermal cut-outs) which act directly on the power sources of water heaters.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15096:2020(Main)
Devices to prevent pollution by backflow of potable water - Hose Union anti-vacuum valves - DN 15 to DN 25 inclusive Family H, type B and type D - General technical specification
EN 15096:2020

This European Standard specifies:
a)   the field of application;
b)   the requirements of hose union anti vacuum valves;
c)   dimensional and physio-chemical properties, and properties of general hydraulic, mechanical and acous-tic design of hose union anti-vacuum valves of nominal sizes DN 15 up to and including DN 25;
d)   marking and technical product information.
This standard specifies the characteristics of hose union anti-vacuum valves of nominal size DN 15 up to and including DN 25 that are suitable for use in drinking water systems at pressures up to and including 1 MPa (10 bar) and temperatures up to and including 65 °C and for 1 h at 90 °C.
HB protects against back siphonage only and should be installed in vertical downward flowposition.
HB and HD anti-vacuum valves are for installation exclusively at the connecting point between stop valve and hose in vertical downward flow position.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1487:2014(Main)
Building valves - Hydraulic safety groups - Tests and requirements
EN 1487:2014

EN 1487 specifies dimensions, materials and performance requirements (including methods of test) for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures1) from 0,1 MPa (1 bar) to 0,7 MPa (7 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95°C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this European Standard does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15092:2009(Main)
Building valves - Inline hot water supply tempering valves - Tests and requirements
EN 15092:2008

This European Standard specifies, dimensions, materials and performance requirements (including methods of test) for in line, hot water supply tempering valves for potable hot water systems, of nominal sizes from DN 15 to DN 50, having working pressures from 0,02 MPa (0,2 bar) to 1,0 MPa (10 bar). Tempering valves reduce the temperature of domestic hot water for distribution throughout the hot water system. The valves are designed for use with hot water up to 90 °C and cold water of less than 25 °C, for use in water supply systems in buildings.
The valves are typically intended to be used with storage water heaters to provide tempered hot water to the terminal fitting. They are not intended to control the comfort temperature at the point of use.
Tempering valves control the distribution temperature from a water heater to a present value or an adjustable range, both between 45 °C and 65 °C.
The essential characteristics according to the mandate which will be dealt with in this standard will be:
a)   Dimensional tolerances
b)   Internal pressure; tightness
c)   Mechanical strength (Torsional strength, bending strength)
d)   Resistance to high and low temperatures
e)   Fitness for contact with drinking water; release of dangerous substances
f)   Protection against backflow
g)   Durability against corrosion and mechanical stress
h)   Noise level
i)   Effectiveness of the device

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14454:2005(Main)
Devices to prevent pollution by backflow of potable water - Hose union backflow preventer DN 15 to DN 32 - Family H, type A
EN 14454:2005

This document specifies:
a)   field of application;
b)   requirements for hose union backflow preventer;
c)   dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical and acoustic design of hose union backflow preventers DN 15  to DN 32;
d)   test method and requirements for verifying these properties;
e)   marking and presentation;
f)   acoustics.
This document specifies the characteristics of hose union backflow preventers DN 15 to DN 32 that are suit-able for use in drinking water systems at pressures up to 1 MPa (10 bar) and temperatures up to 65 °C and for 1 h at 90 °C.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14455:2005(Main)
Devices to prevent pollution by backflow of potable water - Presssurised air inlet valves DN 15 to DN 50 - Family L, type A and type B
EN 14455:2005

This document specifies:
a)   field of application;
b)   requirements for pressurised air inlet valves;
c)   dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical and acoustic design of pressurised air inlet valves DN 15 to DN 50;
d)   test procedure and requirements for verifying these properties;
e)   marking and presentation;
f)   acoustics.
This document specifies the characteristics of pressurised air inlet valves DN 15 to DN 50 that are suitable for use in drinking water systems at pressures up to 1 MPa (10 bar) and temperatures up to 65 °C and for 1 h at 90 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13076:2003(Main)
Devices to prevent pollution by backflow of potable water - Unrestricted air gap-Family A - Type A
EN 13076:2003

This CEN standard specifies the characteristics of type AA air gaps for inlet or feed pipes. Air gaps that comply with the requirements of this standard are devices for protection of drinking water installations from pollution. In addition to factory assembled products this standard includes requirements for site constructed air gaps. This is a performance standard for "AA" air gaps. Materials of construction must be fit for the purpose and application to ensure compliance with this standard during normal working use.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 1717:2023(Main)
Protection against pollution of water intended for human consumption in potable water installations and general requirements for devices to prevent pollution by backflow
prEN 1717

This document specifies a methodology for protecting potable water in potable water installations within and outside buildings but within premises from the risk of pollution by backflow of non-potable water and gives recommendations on the design, risk analysis, backflow prevention devices and their installation methods.
This methodology is also intended to be used outside premises for all potable water systems connected to a potable water distribution system up to and including the point of use.
The product standards for the specific backflow prevention devices or arrangements are intended to be used in conjunction with this document. In the absence of a product standard, this document is intended to be used as a reference to draw up a specification for the development of new devices or arrangements.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day