SIST ISO 2234:1996

SLOVENSKI STANDARD
SIST ISO 2234:1996
01-marec-1996
(PEDODåD&HORYLWDQDSROQMHQDWUDQVSRUWQDHPEDODåD3UHVNXVVNODGDQMDV
VWDWLþQRREUHPHQLWYLMR
Packaging -- Complete, filled transport packages -- Stacking tests using static load
Emballages -- Emballages d'expédition complets et pleins -- Essai de gerbage utilisant
une charge statique
Ta slovenski standard je istoveten z: ISO 2234:1985
ICS:
55.180.40 Celovita, napolnjena Complete, filled transport
transportna embalaža packages
SIST ISO 2234:1996 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 2234:1996

---------------------- Page: 2 ----------------------

SIST ISO 2234:1996
International Standard
INTERNATIONAL ORGANIZATION FOR STANDARDIZATIONoME~YHAPOAHAFl OPI-AHM3ALWlR fl0 CTAHAAPTbl3ALWl*ORGANISATION INTERNATIONALE DE NORMALISATION
Complete, filled transport packages -
Packaging -
Stacking tests using static load
Essai de gerbage utilisan t une Charge sta tique
Emballages - Emballages d’expedition comple ts et @eins -
Second edition - 1985-12-15
Ref. No. ISO 22344985 (E)
UDC 621.798.1 : 620.1657
w
-
complete-and filled packages, tests, stacking tests.
Descriptors : packing, transport packing,
Price based on 2 pages

---------------------- Page: 3 ----------------------

SIST ISO 2234:1996
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bodies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 2234 was prepared by Technical Committee ISO/TC 122,
Packaging.
This second edition cancels and replaces the first edition (ISO 2234~1972), which has
been technically revised as follows:
- two new, alternative methods for carrying out the stacking test have been
specif ied;
a new clause on “Package preparation” has been added.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless othetwise stated.
0 International Organkation for Standardkation, 1985
Printed in Switzerland

---------------------- Page: 4 ----------------------

SIST ISO 2234:1996
ISO 22344985 (El
INTERNATIONAL STANDARD
Packaging - Complete, filled transport packages -
Stacking tests using static load
4.2 Means of loading, which, according to the method
1 Scope and field of application
Chosen (1, 2 or 31, is as described in 4.2.1 to 4.2.3.
This International Standard specifies three methods for carry-
ing out a stacking test on a complete, filled transport package,
using a static load. Whichever method is employed, the test
4.2.1 Method 1: Stack of packages, each package being
may be used to assess the Performance of a package in terms
identical with the package under test. The number of packages
of its strength or the protection that it offers to its contents
is such that their total mass forms an appropriate load.
when it is subjected to stacking. lt may be performed either as a
Single test to investigate the effects (deformation, creep, col-
4.2.2 Method 2: loading platform, free to tilt to an
lapse or failure) of stacking or as part of a sequence of tests
equilibrium Position on the test package, together with an ap-
designed to measure the ability of a package to withstand a
propriate load. The load and loading platform may be integral.
distribution System that includes a stacking hazard.
The test may also be used to investigate performante under
The loading platform, when placed centrally on top of the test
particular conditions of loading, as, for example, when the bot-
package, shall be large enough to extend to at least 100 mm
tom package in a Stack rests on an open-decked pallet; or when
over all sides of the top surface of the package and rigid
the Profile of the superimposed load is eccentric, as when it is
enough to support the load completely without deformation.
supported on the bearers of a Single-decked pallet which rests
on a Container. For such purposes, one of the three methods of
- This type of load is sometimes referred to as “free load”.
NOTE
carrying out the test may be more suitable than the others.
NOTE - A method for carrying out a stacking test using a compres-
4.2.3 Method 3: loading platform, such that the lower sur-
sion tester is given in ISO 2874.
face of the platform is constrained to remain horizontal,
together with an appropriate load. The load and loading plat-
2 References form may be integral.
ISO 2206, Packaging - Complete, filled transport packages -
The loading platform, when placed centrally on top of the test
lden tifica tion o f Parts when testing.
package, shall be large enough to extend to at least 100 mm
over all sides of the top surface of th
...

Norme internationale @ 2234
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION*MEW(flYHAPO&HAR OPrAHHJAUHR no CTAHnAPTM3AUHH.ORGANlSATlON INTERNATIONALE DE NORMALISATION
Emballages - Emballages d'expédition complets et pleins -
L
Essai de gerbage utilisant une charge statique
Packaging - Complete, filled transporï packages - Stacking tests using static load
Deuxième édition - 1985-12-15
CDU 621.798.1 : 620.1.165.7 Réf. no : ISO2234-1985 (F)
- 5
Descripteurs : emballage, emballage d'expédition, emballage complet-et plein, essai, essai de gerbage.
M
s
Prix bas6 sur 2 pages

---------------------- Page: 1 ----------------------
~~~~~ ~
NORM E I NTE R NAT1 ON ALE
IS0 2234-1985 (F)
Emballages - Emballages d'expédition complets et pleins -
Essai de gerbage utilisant une charge statique
1 Objet et domaine d'application 4 Appareillage
La présente Norme internationale spécifie trois méthodes
4.1 Surface horizontale, plane (la différence de hauteur
d'essai de gerbage des emballages d'expédition complets et
entre le point le plus élevé et le point le plus bas ne devant pas
pleins, utilisant une charge statique. Quelle que soit la méthode
dépasser 2 mm) et rigide. Un plancher en béton d'une épaisseur
mise en œuvre, l'essai peut être utilisé pour évaluer les caracté-
d'au moins 150 mm convient.
ristiques d'un emballage en fonction de sa résistance ou de la
L.
protection qu'il offre à son contenu lors du gerbage. L'essai
Dispositifs de chargement qui, selon la méthode utili-
4.2
peut être effectué comme essai simple dans le but d'examiner
sée (1, 2 ou 3), sont tels que décrits en 4.2.1 à 4.2.3.
les effets (déformation, glissement, effondrement ou défail-
lance) de ce gerbage, ou il peut faire partie d'une série d'essais
4.2.1 Pour la méthode 1 : Pile d'emballages, chacun d'eux
destinés à mesurer la résistance d'un emballage dans un
étant identique à l'emballage soumis à l'essai. Le nombre
système de distribution qui comprend un risque au gerbage.
d'emballages doit être tel que leur masse totale constitue une
charge appropriée.
L'essai peut également être utilisé pour déterminer le comporte-
ment d'un emballage placé dans des conditions particulières de
mise en charge, comme lorsque l'emballage inférieur d'une
4.2.2 Pour la méthode 2: Plateau de chargement, non
gerbe repose sur une palette à tablier ouvert, ou lorsque le profil
guidé, placé en position d'équilibre au-dessus de l'emballage
de la charge superposée est excentrique dans le cas où elle est d'essai, avec une charge appropriée. La charge et le plateau de
supportée par les appuis d'une palette à simple tablier reposant
chargement peuvent c
...